SuperLoader 3A Series
SuperLoader™ 3A Series
Quick Start Guide
Contents
0
Choosing a Location.......................... 1
Preparing for the Installation........... 2
Providing Necessary Tools ............. 2
Taking ESD Precautions ................. 3
Preparing for Rack Mounting ........ 3
Unpacking the Autoloader................ 4
Checking Accessories ..................... 5
Rack Mounting the Autoloader........ 6
Autoloader Panel Overviews........... 12
Connecting Ethernet
and Power Cables......................... 13
®
The Quantum SuperLoader™ 3A Series autoloader is an automated
storage and retrieval device with an integrated A-Series tape drive and up
to two tape magazines holding up to eight cartridges each. It has a built-in
FTP server and Web interface.
After the Installation....................... 14
For more information, see the SuperLoader 3A Series User’s Guide
(PN 81-81643) and the A-Series FTP File Server User’s Guide (PN 81-81800) on
the documentation CD provided with your autoloader.
This quick start guide uses the following conventions:
Note: Notes emphasize important information related to the main
topic.
Caution: Cautions indicate potential hazards to equipment and are
included to prevent damage to equipment.
Warning: Warnings indicate potential hazards to personal safety and
are included to prevent injury.
This document explains how to unpack the SuperLoader 3A Series
autoloader and install it in a standard 19-inch rack.
Choosing a Location
The autoloader is designed to fit in a standard 19-inch rack using either the
long or short brackets (depending on the depth of the rack). The autoloader
uses standard rack mounting hardware.
Note: It is recommended that you review this entire document prior to
beginning the installation.
SuperLoader 3A Series
Some components within the autoloader contain static-sensitive parts. To avoid damaging
these parts while performing installation procedures, always observe the following
precautions:
Taking ESD Precautions
0
•
Ensure that the work area is free from conditions that could cause electrostatic
discharge (ESD).
•
Discharge static electricity from your body by touching a known grounded surface,
such as your computer's metal chassis.
•
•
•
Keep the autoloader turned off during all installation procedures.
Use an antistatic wrist strap.
Keep static-sensitive parts in their original shipping containers until ready for
installation. Look for the ESD sticker to identify static sensitive parts.
•
Avoid touching connectors and other components.
Note: Dry climates and cold-weather heating environments have lower relative
humidity and are more likely to produce static electricity.
Preparing for Rack
Mounting
The autoloader can be rack mounted by attaching it directly to stationary cabinet rails.
Take the following general safety steps before beginning the rack-mount installation.
1 Lower the cabinet feet.
0
2 Extend the cabinet anti-tip device, if available.
Note: An anti-tip device may be extendable legs or similar equipment used to
stabilize the cabinet. This anti-tip equipment is to help avoid over-
balancing the cabinet when installing or removing equipment.
3 Ensure that the cabinet and all rack mounted equipment have a reliable ground
connection.
4 Verify that the total current of all rack mounted components (including the
autoloader) will not exceed the current rating of the power distribution unit or outlet
receptacles.
5 Secure the help of at least one other person. At least two people are required to safely
install the autoloader into a rack cabinet.
Warning: Failure to take these safety steps may result in personal injury or
equipment damage.
Preparing for the Installation
3
SuperLoader™ 3A Series Quick Start Guide
Caution: Do not remove the top cover of the autoloader during the installation
process. Removing the top cover could result in damage to the
autoloader.
Unpacking the Autoloader
Before you begin, clear a desk or table so that you can unpack the autoloader.
The SuperLoader 3A Series Quick Start Guide has all the necessary information to unpack
and inspect your autoloader correctly.
You also need to select an open 2U computer rack location near the server that will host
the autoloader.
Caution: If the room in which you are working differs from the temperature in
which the autoloader was shipped or stored by 15° C (30° F) or more, let
the autoloader acclimate to the surrounding environment for at least 12
hours before removing it from the shipping carton.
Caution: If your unit was ordered as a one-magazine autoloader, be sure to remove
the plastic shipping insert from the magazine bay before connecting or
operating your autoloader. Insert either a magazine or a magazine blank
into the bay. The autoloader will not function without both magazine bays
equipped with either a magazine or a magazine blank.
Carefully unpack and inspect your new SuperLoader 3A Series autoloader by doing the
following:
1 Inspect the shipping box for damage. If you notice any damage, report it to the
shipping company immediately.
2 Open the shipping box and remove the accessories package. Set the accessories
package aside for now.
3 Lift the autoloader and padding out of the box and place it on the work surface, top
facing up. Do not set the autoloader on either end or sides.
4 Carefully remove the shipping padding from the left and right sides of the
autoloader. Then remove the bag from the autoloader.
5 Remove the foam insert from the magazine bay of the autoloader. Save the packing
materials in case you need to move or ship the autoloader in the future.
Note: If the cover must be taken off, there are 26 screws that need to be removed.
4
Unpacking the Autoloader
SuperLoader 3A Series
The following accessories are shipped with the SuperLoader 3A Series autoloader:
0
Checking Accessories
•
SuperLoader 3A Series Quick Start Guide
Ethernet cable
•
•
•
Four autoloader brackets (two long and two short to accommodate different rack
depths)
•
•
Two support brackets
Two sets (decimal and metric) of four support bracket 10-32 x 1/4 inch button
head screws (two per support bracket)
®
•
•
•
TORX L-Key drivers (T8 and T10)
Power cable
®
Documentation CD containing all of the documentation in Adobe Portable
Document Format (PDF)
•
Bar code labels
You will also need the following parts that were shipped with your rack:
•
•
Eight clip nuts
Eight rack screws
Figure 1 Rack Mount
Hardware
Support brackets
(74-60605-01)
Short autoloader
brackets (72-A225-A)
Long autoloader
brackets (72-A226-A)
Support bracket screws
72-A348-A (4) or 90-60227-50 (4)
Unpacking the Autoloader
5
SuperLoader™ 3A Series Quick Start Guide
Rack Mounting the Autoloader
This section provides the steps for attaching the autoloader directly to the stationary rails
of a rack. Refer to table 1 for information on common rack hole types.
Table 1 Rack Hole Types
Figure
Description
Square rack holes are the most
common type of rack holes.
They can accept either cage
nuts which mount from the back
of the rail or clip nuts which clip
on from the side of the rack rail.
Cage nut
Clip nut
Through holes require clip nuts
to accept mounting hardware.
Clip nut
Threaded holes require neither
cage or clip nuts to accept
mounting hardware.
Note: The rails within the rack have a hole pattern that repeats throughout the rail.
1 Install two clip nuts, 1.75 in. (44.45 mm) apart, onto each of the four rails of the rack,
making sure that you install each pair of clip nuts at exactly the same level (see
figure 2).
6
Rack Mounting the Autoloader
SuperLoader 3A Series
Figure 2 Installing Two Clip
Nuts
Rail
Rail
Clip nut
Outer covers
of the rack
1.75 in
(44.45 mm)
Rail
Clip nut
2 Select the long or short autoloader brackets (depending on the depth of the rack), and
then attach them to the rear of the autoloader (see figure 3). Use the long autoloader
brackets (72-A226-A) when the distance from the front mounting rail to the rear
mounting rail is less than 30.25 in. (76.84 cm). Otherwise, use the short autoloader
brackets (72-A225-A).
Rack Mounting the Autoloader
7
SuperLoader™ 3A Series Quick Start Guide
Figure 3 Attaching Autoloader
Brackets
Autoloader
Screws (10-32 x 1/4 only)
Autoloader bracket
3 Using rack screws, attach a support bracket to the clip nuts on each rear rail (see
figure 4.)
Note: Be sure to attach the support brackets correctly; the side of the bracket with
only two holes should be secured to the rail.
Tighten the screws just enough to hold the support brackets firmly against the rail
while still allowing the support bracket to be slightly shifted by hand. This shifting
will help facilitate the engagement of autoloader brackets as the autoloader is
installed in the rack. You will fully tighten the screws in step 8.
8
Rack Mounting the Autoloader
SuperLoader 3A Series
Figure 4 Attaching Support
Brackets
Clip nuts
Support bracket
Rack screws
Rear rail in rack
Outer cover of rack
4 With the help of a second installer, insert the autoloader into the rack so that the
autoloader brackets slide into corresponding support brackets on the rear rails and
the tabs at the front of the autoloader align flush with the clip nuts on the front rails
(see figure 5).
Caution: Do not release the front end of the autoloader until it can be secured to
the rack.
Rack Mounting the Autoloader
9
SuperLoader™ 3A Series Quick Start Guide
Figure 5 Sliding Autoloader
into Rack
Autoloader bracket
Support bracket
5 While the other installer holds the front end of the autoloader, secure the front end of
the autoloader to the rack using four rack screws (two per tab) as shown in figure 6.
Tighten the screws just enough to secure the autoloader to the front rails.
Figure 6 Front Alignment
Front rail
Autoloader
(front)
Rack screws
Tab (one per side)
6 Install four screws (two per side) to secure the support brackets to the autoloader
brackets (see figure 7).
10
Rack Mounting the Autoloader
SuperLoader 3A Series
Figure 7 Connecting Support
Brackets
Support bracket
Autoloader bracket
Screws
7 Verify that the autoloader is level. Adjust as needed.
8 When the autoloader is level, tighten all screws securing the autoloader to the rack.
This includes the following:
•
•
•
Four screws securing the autoloader tabs to the front rails.
Four screws securing the support brackets to the rear rails.
Four screws securing the autoloader brackets to the support brackets.
Rack Mounting the Autoloader
11
SuperLoader™ 3A Series Quick Start Guide
Autoloader Panel Overviews
The front panel allows you to configure the autoloader, enter commands, and obtain
status information.
Figure 8 Front Panel Overview
1
2
3
4
5
6
7
Power switch
Mailslot
Front panel LEDs
Front panel LCD screen
Function keys
Left magazine (or blank)
Right magazine (or blank)
The Ethernet ports on the back panel allow you to connect to the A-Series tape drive FTP
file server and to the autoloader remote management interface.
Figure 9 Back Panel Overview
1
2
3
4
5
A-Series tape drive FTP file server Ethernet port
Fan vent
Power connector
Autoloader remote management Ethernet port
Power switch
12
Autoloader Panel Overviews
SuperLoader 3A Series
Connecting Ethernet and Power Cables
To connect the Ethernet and power cables to the autoloader, follow these steps:
1 Attach one end of the Ethernet cable (included in the accessory kit) to the tape drive
Ethernet port on the back panel of the autoloader.
2 Attach the other end of the Ethernet cable to your host network port or router.
3 Attach the female connector of the power cable to the power connector on the back
panel of the autoloader.
4 Plug in the power cable to the nearest properly grounded power outlet, then turn on
the power switch on the back panel of the autoloader.
Caution: Whenever you power cycle the autoloader, allow 10 seconds before
turning the power back on. The power supply requires at least two to
three seconds for the capacitors to discharge. This ensures a complete
system reset on power down and may avoid system errors.
5 Turn on the autoloader by setting the power switch on the back panel to the ON
position and pressing the power switch on the front panel. Check the LCD screen to
make sure the autoloader is receiving power. If it is not, check the power connections
and your power source.
During the Power-on Self Test (POST), both LEDs are illuminated briefly, followed by
only the Ready/Activity LED flashing. When the initialization sequence is complete,
the LCD screen displays the Home screen.
Note: The autoloader will not complete the initialization sequence unless both
tape magazine openings are properly closed. You can use two magazines
or one magazine and one magazine blank.
Note: When the SuperLoader 3A Series is powered up, it undergoes a media
inventory. Each tape cartridge in the autoloader is inserted into the
A-Series tape drive and inventoried. Depending upon the number of
cartridges in each magazine and the amount of content or data on each
cartridge, the media cartridge inventory may take up to forty minutes.
Connecting Ethernet and Power Cables
13
SuperLoader™ 3A Series Quick Start Guide
After the Installation
From the front panel of the autoloader, use the menus to set the IP address (DHCP or
Static), Subnet Mask (if required), Gateway (if required), SNMP Server (optional), and
Time Server (optional).
The default IP address is 192.168.20.128.
The default login and password for the On-board Remote Manager is guest and guest.
For detailed information on the setup, operation, and administration of your system
(including accessing and using the FTP file server), see the SuperLoader 3A Series User’s
Guide (PN 81-81643) and the A-Series FTP File Server User’s Guide (PN 81-81800) on the
documentation CD provided with your autoloader.
*81-81667-02 A01*
81-81667-02 A01
Quantum Corp. (NYSE: QTM) is the leading global storage company
For assistance contact Quantum Technical Assistance center:
specializing in backup, recovery and archive. Combining focused
expertise, customer-driven innovation, and platform independence,
Quantum provides a comprehensive range of disk, tape, media, and
software solutions supported by a world-class sales and service
organization. As a long-standing and trusted partner, the company works
closely with a broad network of resellers, OEMs, and other suppliers to
meet customer’s evolving data protection needs.
North America
UK, France, and Germany
EMEA
+1-800-284-5101
00800 4 QUANTUM
+44 1256 848 766
For worldwide support: www.quantum.com/contactsupport
Backup. Recovery. Archive. It’s What We Do.
©2007 Quantum Corporation. All rights reserved. Quantum, the Quantum logo, and all other
logos are registered trademarks of Quantum Corporation or their respective owners.
81-81667-02 A01 August 2007
|