owner’s manual
200 Watt Stereo Receiver
with Remote Control
INTRODUCTION
Your RCA 200 Watt Stereo Receiver operates as the perfect control
center for your audio system. It combines 100 watts-per-channel of
clean power with modern styling. It provides connections for one
tape deck, a turntable, a CD player, and one other audio source, such
as audio from a digital video disk (DVD) player. You can also connect
up to two pairs of speakers (not supplied) to your receiver.
THE FCC WANTS YOU TO KNOW
Your receiver might cause radio or TV interference even when it is
operating properly. To determine whether your receiver is causing
the interference, turn off your receiver. If the interference goes away,
your receiver is causing it. Try to eliminate the interference by:
Additional benefits include:
• Moving your radio or TV away from the receiver
• Connecting your receiver to an outlet that is on a different
electrical circuit from the radio or TV
Digital-Synthesized Tuner — Precisely tunes to AM and FM
stations.
• Contacting your local RadioShack store for help
60 Memory Locations — Let you store and recall the frequencies
If you cannot eliminate the interference, the FCC requires that you
stop using your receiver.
for up to 30 AM and 30 FM stations.
Automatic Tuning — Searches for the next available AM/FM
station.
This system complies with the limits for a Class B digital device as
specified in Part 15 of FCC Rules. These limits provide reasonable
protection against radio and TV interference in a residential area.
However, your equipment might cause TV or radio interference even
when it is operating properly. To eliminate interference, you can try
one or more of the following corrective measures:
Remote Control — Lets you use a single remote control for the
receiver and other compatible components connected to the receiver.
Tape Monitoring — Lets you listen to the actual recording as you
record, if your tape deck has a tape-monitoring feature.
• Reorient or relocate the receiving antenna.
Built-In Protection Circuits — Automatically turn off the receiver
to help avoid power surges or short circuit damage.
• Increase the distance between the equipment and the radio or
TV.
• Use outlets on different electrical circuits for the equipment and
the radio or TV.
Note: The remote control requires two AA batteries (not supplied).
WARNING: To reduce the risk of fire or shock hazard, do not
expose this product to rain or moisture.
Consult your local RadioShack store if the problem still exists.
Warning: Changes or modifications to this unit not expressly
approved by RadioShack could void the user’s authority to operate
the equipment.
CAUTION
RISK OF ELECTRIC SHOCK. DO
!
NOT OPEN.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER OR BACK. NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED PERSONNEL.
IMPORTANT SAFETY
INSTRUCTIONS
This symbol is intended to alert you to the
presence of uninsulated dangerous voltage
within the product’s enclosure that might be
of sufficient magnitude to constitute a risk of
electric shock. Do not open the product’s
case.
Careful attention is devoted to quality standards in the manufacture
of your receiver, and safety is a major factor in its design. However,
safety is also your responsibility.
This section lists important information that will help you properly
use and enjoy your receiver.
This symbol is intended to inform you that
important operating and maintenance
instructions are included in the literature
Heed Warnings — Follow all warnings on the product and in the
operating instructions.
!
accompanying this product.
Cleaning — Unplug this product from the wall outlet before
cleaning. Use only a damp cloth for cleaning. Do not use liquid or
aerosol cleaners.
Caution: Unplug the cassette deck's power cord when you will not
use the cassette deck for extended periods.
Attachments — Do not use attachments/accessories not
recommended by the product manufacturer, as they might create a
hazard.
3
Water and Moisture — Do not use this product near water (for
example, near a bathtub, washbowl, kitchen sink, or laundry tub; in
a wet basement; or near a swimming pool).
Damage Requiring Service — Unplug this product from the wall
outlet and refer servicing to qualified service personnel under the
following conditions:
• When the power-supply cord or plug is damaged.
• If liquid has been spilled or objects have fallen into the product.
• If the product has been exposed to rain or water.
Accessories — Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury
to a child or adult, and serious damage to the product. Use only with
a cart, stand, tripod, bracket, or table recommended by the
manufacturer or sold with the product.
• If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions, as an improper
adjustment of other controls may result in damage and will often
require extensive work by a qualified technician to restore the
product to normal operation.
Follow the manufacturer's instructions for mounting, and use a
recommended mounting accessory.
Carts — Move the product on a cart carefully. Quick stops,
excessive force, and uneven surfaces may cause the product/cart to
overturn.
• If the product has been dropped or damaged in any way.
• When the product exhibits a distinct change in performance.
Ventilation — Slots and openings in the cabinet provide ventilation,
ensure reliable operation, and protect from overheating. Do not
block or cover these openings, and do not place the product on a
bed, sofa, rug, or other similar surface. Do not place the product in a
built-in installation such as a bookcase or rack unless it provides
proper ventilation as specified by the manufacturer.
Replacement Parts — When replacement parts are required, be
sure the service technician uses replacement parts specified by the
manufacturer or having the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other
hazards.
Safety Check — Upon completion of service or repairs to this
product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
Power Sources — Operate this product using only the power
source indicated on its marking label. If you are not sure of your
home's power type, consult your product dealer or local power
company.
Wall or Ceiling Mount — The product should be mounted to a
wall or ceiling only as recommended by the manufacturer.
Polarization — This product is equipped with a polarized AC line
plug (a plug having one blade wider than the other). This plug will
fit in the power outlet only one way. This is a safety feature. If you
cannot insert the plug fully into the outlet, try reversing the plug. If
the plug still doesn't fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of the polarized
plug. If you need an extension, use a polarized cord.
Heat — The product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
Non-use Periods — Unplug the receiver’s power cord when you
will not use it for extended periods.
Power-Cord Protection — Route power-supply cords so they are
not likely to be walked on or pinched by items placed on or against
them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
Power Lines — Locate an outdoor antenna away from power lines.
Outdoor Antenna Grounding — If an outside antenna or cable
system is connected to the receiver, ground the antenna or cable
system so as to provide some protection against voltage surges and
built-up static charges. Article 810 of the National Electrical Code,
ANSI/NFPA 80, provides information about proper grounding of the
mast and supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors, location of
antenna-discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode. See the example below.
Lightning — For added protection for this product during a
lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent damage to the product
due to lightning and power-line surges.
Overloading — Do not overload wall outlets, extension cords, or
integral convenience receptacles, as this can result in a risk of fire or
electric shock.
Antenna
Lead-In
Wire
Objects and Liquids — Never push objects of any kind into this
product through openings, as they may touch dangerous voltage
points or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
Ground Clamp
Antenna
Discharge Unit
(NEC Section 810-20)
Electric
Service
Grounding Conductors
(NEC Section 810-21)
Equipment
Grounding Clamps
Servicing — Do not attempt to service this product yourself, as
opening or removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service personnel.
Power Service Grounding
Electrode System
(NEC Article 250, Part H)
NEC -- National Electrical Code
4
PREPARATION
Caution: Make all the necessary connections before you plug in or
turn on the receiver.
Use 16-gauge (or larger) speaker wire for all speaker connections,
and consider possible speaker locations before you decide how much
speaker wire you need.
POSITIONING SPEAKERS
Preparing the Speaker Wires
Speaker wire consists of two conductors (individual wires) encased
in insulation and is usually color-coded or marked with a ridge along
one side so you can identify each conductor. Use these markings as a
guide to help you properly connect the speakers to your receiver.
Follow these steps to prepare the speaker wires.
1. Cut the speaker wires to the necessary length.
2. Separate the wires about 4 inches on each end.
3. Using a wire stripper, carefully strip about 3/4 inch of insulation
from the end of each conductor.
4. Twist the end of each conductor to secure any loose wire
strands.
Speaker (not supplied) placement can make a noticeable difference
in your system’s sound. The guidelines in this section will help you
choose the best locations. After you use your receiver for a while, you
might want to try different locations for your speakers.
Caution: Twisting the end of each conductor helps prevent a short
circuit because stray speaker wire strands do not touch other speaker
terminals or any other receiver terminals.
Bass response depends largely on speaker location. For strong bass,
place the speakers in the corners of the room. If you want even
stronger bass, place the speakers directly on the floor. If the bass is
too strong, move the speakers slightly away from the corners of the
room, or raise them 6 to 18 inches off the floor. You can buy speaker
stands at your local RadioShack store.
Connecting Speakers to the A and B Terminals
Notes:
• Be sure you connect the receiver’s right and left positive (+) and
negative (–) terminals to the speaker’s corresponding right and
left positive (+) and negative (–) terminals.
The distance between the speakers should be about the same as the
distance between the normal listening point and the point halfway
between the speakers. If you place the speakers too close together,
you reduce the stereo separation. If you place them too far apart, you
reduce the bass effect and create a hole in the middle of the sound.
• Fully insert the speaker wires to ensure a good connection.
Leave extra wire at the back of the receiver so you do not
disconnect the wires when you move the receiver.
Follow these steps to connect each speaker (A right or left or B right
or left).
Most speakers have a tweeter dispersion angle of about 60 degrees.
Ideally, your listening position should be just inside the overlap area
of the tweeter dispersion. You can angle the speakers toward you for
better stereo effect.
1. Press open the receiver’s positive (+) red lever for the speaker
you want to connect and insert the ridged or color-coded
conductor’s end into the small hole. Release the lever to secure
the conductor.
CONNECTING SPEAKERS
Follow these guidelines when you select and connect speakers.
• Only connect speakers that are rated at between 8 and 16 ohms.
• Be sure you properly connect all speakers.
• Do not connect two pairs of speakers to a single set of terminals
(A or B) at the same time. When you use two pairs of speakers,
connect one pair to the A SPEAKERS terminals and the other
pair to the B SPEAKERS terminals.
2. Press open the receiver’s negative (–) black lever for the same
speaker and insert the other conductor’s end into the small hole.
Release the lever to secure the conductor.
• RCA and other high-quality speakers have color-coded speaker
terminals (red for positive polarity and black for negative
polarity). Use these color-coded terminals as a guide to help you
properly connect the speakers to the receiver.
5
3. Connect the ridged or color-coded conductor’s loose end to the
speaker’s positive (+) terminal.
CONNECTING THE ANTENNAS
In many areas, the supplied indoor AM loop and FM antennas
provide satisfactory reception.
4. Connect the remaining loose conductor to the speaker’s negative
(–) terminal.
AM Antennas
CONNECTING PROGRAM SOURCES
Assemble the supplied AM antenna’s base by swinging the base in the
direction of the arrow and inserting the antenna’s bottom tabs into
the base’s slot. If the receiver is in a rack or on a shelf and there is no
room for the AM loop antenna, use two screws (not supplied) to
mount the base on the wall or another location as shown.
Note: Use shielded audio cables with phono connectors for all audio
connections.
You can connect up to four external program sources to your
receiver.
Connecting a Turntable
Connect a turntable with a magnetic cartridge only. Some older
turntables use a ceramic-type cartridge that does not work with this
system.
Attach the antenna wires from the AM loop antenna to the AM and
GND (ground) ANTENNA terminals.
Connect the turntable’s left and right cables to the receiver’s L (left)
and R (right) PHONO IN jacks. Then connect the turntable’s ground
wire to the receiver’s GND screw terminal.
Connecting a CD Player
To connect a CD player to the receiver, connect the CD player’s left
and right output jacks to the receiver’s L and R CD IN jacks.
Place the antenna on a flat surface and rotate it for the best AM
reception.
Connecting a Cassette Deck
Notes:
You can connect a cassette deck to the TAPE MONITOR jacks.
Connect the cassette deck’s output jacks to the PLAY jacks, and
connect the cassette deck’s input jacks to the REC jacks.
• Keep the AM loop antenna connected even when you use
another indoor antenna or an outdoor AM antenna.
• Ensure that the antenna does not touch the receiver or any other
metal object.
Connecting Another Audio Source
Connect the audio outputs of another audio source, such as the
audio from a laser disc player, TV, or VCR to the AUX jacks.
• Do not place the antenna near a CD player, a personal computer,
or a TV set.
• If the wire between the AM loop antenna and your receiver is
too short, you can add extra wire, available at your local
RadioShack store.
6
You can also use an optional RadioShack shortwave antenna kit,
which makes an excellent outdoor AM antenna. Connect the outdoor
AM antenna wire to the receiver’s AM ANTENNA terminal as shown.
3. Fold back the shielding from the inner insulation.
4. Remove about 1 inch of the inner insulation from around the
center wire.
5. Pull the shielding to one side. Connect the center wire to the
receiver’s FM 75Ω ANTENNA terminal. Twist the shielding to
secure any loose wire strands, and connect it to the GND
ANTENNA terminal.
FM Antennas
Connect the supplied FM antenna to the FM 300Ω ANTENNA
terminal as shown then extend it.
Caution: The cable’s shielding should only touch the GND
ANTENNA terminal.
Note: Grounding is not necessary for reception, but we recommend
it for better FM reception and to avoid damage from lightning when
you use an outdoor FM antenna. Use a separate piece of thick
polyvinyl insulated wire to connect the GND ANTENNA terminal to
an earth ground, such as a metal cold-water pipe.
For better FM reception, you can also use a rabbit-ear TV antenna
(for indoor use only) or an outdoor VHF TV antenna. To connect the
TV antenna to the receiver, you need a VHF/ UHF/FM splitter (not
included). RadioShack stores carry a full line of quality antennas and
antenna connection accessories.
Warning: Never connect a wire to a gas pipe for grounding since
sparks might ignite the gas.
Warning: To prevent injury, read and follow all cautions and
warnings that accompany the outdoor antenna. Use 75-ohm coaxial
cable to connect an outdoor antenna to the receiver.
For the best radio reception, use an outdoor antenna. Follow these
steps to connect an outdoor FM antenna to the receiver using 75Ω
coaxial cable.
Note: If your antenna has 300Ω twin-lead cable, connect it to the FM
300Ω ANTENNA terminals.
1. Disconnect the supplied FM antenna from the receiver’s FM
300Ω ANTENNA terminal.
2. With a stripping tool, remove about 11/2 inches of the 75Ω
cable’s outer insulation to expose the cable’s shielding.
7
INSTALLING BATTERIES
CONNECTING TO AC POWER
Cautions:
Warning: To prevent electric shock, do not use this polarized plug
with an extension cord, receptacle, or other outlet unless you can
fully insert the blades to prevent blade exposure.
• Use only fresh batteries of the required size and recommended
type.
Before you plug in the receiver’s power cord, double check all other
connections.
• Do not mix old and new batteries, different types of batteries
(standard, alkaline, or rechargeable), or rechargeable batteries of
different capacities. Your remote control requires two AA
batteries (not included) for power. For the best operation and
longest life, we recommend alkaline batteries, available at your
local RadioShack store.
To power the receiver, plug the supplied power cord into a standard
AC outlet. The power cord’s plug is polarized and fits only one way.
The STAND BY indicator lights when the receiver is plugged in but
turned off.
1. To remove the battery compartment cover, push the
compartment’s tab in the direction of the arrow, then lift off the
cover.
Note: The receiver has a built-in circuit to protect it against
overheating or short circuits. If your receiver automatically turns off
(stand by mode), let it cool for several minutes. If the receiver
overheated, it should play normally when you turn it back on. If
there is a short circuit in your receiver, it will turn off again when you
turn on the receiver. If this happens, check with your local
RadioShack store for service.
2. Place two fresh AA batteries in the compartment as indicated by
the polarity symbols (+ and –) marked inside.
3. Replace the battery compartment cover.
When the range is reduced or the remote stops operating properly,
replace the batteries.
Warning: Dispose of old batteries promptly and properly. Do not
burn or bury them.
Caution: If you do not plan to use the remote with batteries for a
month, remove the batteries. Batteries can leak chemicals that can
destroy electronic parts.
8
OPERATION
AM
TUNING DOWN
TUNING UP
PHONO
CD
FM
TUNING
MODE
TAPE
MONITOR
AUX
VOLUME
LOUDNESS
BALANCE
TREBLE
PRESET
SCAN
POWER
SPEAKERS
A/B
FM MODE
PHONES
BASS
MEMORY
Warning: To prevent possible hearing loss, turn VOLUME to MIN
before you turn on the receiver or change the program source. After
you turn on the receiver or change the program source, adjust
VOLUME to a comfortable listening level.
To listen to a source other than the one connected to the TAPE
MONITOR jacks, press TAPE MONITOR so TAPE MON
disappears. Then press CD, PHONO, or AUX (CD, PHONO, or
AUX appears).
4. Turn VOLUME clockwise to increase the volume or
counterclockwise to decrease it. Or, you can use VOLUME 9
and 8on the remote control.
You can use the supplied remote control by pointing it at the
receiver’s front panel and pressing the desired button(s). Many
buttons on the remote control work the same as buttons on the
receiver’s front panel. Use these buttons exactly as you would use the
corresponding buttons on the receiver.
5. To adjust the tone, turn BASS and TREBLE toward + or –. To
increase the high and low ranges of sound at low volume, press
LOUDNESS. (To turn off this feature, press LOUDNESS again.)
1. Press POWER to turn on the receiver. It takes about 5
6. To adjust the balance of sound between the left and right
speakers, see “Adjusting Balance” on Page 11.
seconds to hear sound.
2. Select the speakers. An indicator lights next to the A and/or B to
7. When you finish using the receiver, press POWER to turn it off.
show which speakers are on.
If you connected speakers only to the A (or B) SPEAKERS
terminals, press SPEAKERS A (or B) to turn on only those
speakers. Do not press both SPEAKERS A and B because doing
so turns off all speakers even though both indicators are on.
USING THE SLEEP TIMER
The sleep timer lets you set the receiver to play for up to 90 minutes,
then automatically turns off.
If you connected speakers to both the A and B SPEAKERS
terminals, you can:
1. To set the timer, turn on the receiver then press SLEEP on the
remote control. The display dims and SLEEP 90 SLEEP
appears.
• Press SPEAKERS A or B to turn on either pair of speakers
for a two-speaker effect.
• Press SPEAKERS A and B to turn on both pairs of speakers
2. To set the sleep timer for less than 90 minutes, repeatedly press
SLEEP to decrease the time by 10 minutes for each press of the
button. Once you select the time, the receiver displays the
program source. (SLEEP stays on the display in small letters
until automatic shut-off.)
for a four-speaker effect.
Press SPEAKERS A and/or B to turn off all speakers so you can
listen privately with headphones (see “Using Headphones” on
Page 11).
3. To briefly see the time remaining, press SLEEP once.
3. Select a program source.
To tune to a radio station, see “Direct Tuning (Remote Control
Only)” on Page 10.
To listen to signals from the component connected to the TAPE
MONITOR jacks, press TAPE MONITOR so TAPE MON appears.
9
Memory Tuning
TUNING THE RADIO
Memory tuning lets you instantly tune to a stored frequency. You can
store up to 30 AM and 30 FM frequencies in the receiver’s memory.
The receiver automatically stores the first 30 stations found in the
selected band into the memory. You can also manually store a station
into memory.
Your receiver has four types of electronic tuning — manual,
automatic, direct, and memory.
Note: To listen to stations with weak signals, we recommend manual
tuning.
Automatically Storing Stations
Manual and Automatic Tuning
1. Press FM or AM on the front panel (or on the remote control) to
select the desired band. The receiver tunes to that band and the
last selected frequency appears.
1. Press FM or AM on the front panel (or on the remote control) to
select the desired band. The receiver tunes to that band and
displays the frequency last selected.
2. Hold down MEMORY for more than 2 seconds. MEMORY and
CH appear and the receiver scans through the frequencies,
beginning with the low end (87.5 MHz for FM or 530 kHz for
AM).
Note: If CH appears on the right side of the display, press
TUNING MODE to switch from preset to manual-tuning mode.
MANUAL briefly appears.
2. To manually select the next higher or lower frequency, press
TUNING UP or DOWN. Hold down UP or DOWN to rapidly
scan up or down through the frequencies. Release the button to
stop scanning.
3. When the receiver finds a station, it stores it in the first memory
channel, the selected CH number appears, and the receiver looks
for the next station. When the receiver finds the thirtieth station
or when it reaches the high end of the frequency range, MEMORY
disappears and the receiver tunes to the lowest frequency station
in the band.
To automatically search for the next higher or lower frequency with a
strong signal, briefly hold down TUNING UP or DOWN. The
receiver searches up or down the band, stopping on the next
frequency with a strong signal.
Repeat these steps to automatically store stations in the other band.
Notes:
Manually Storing a Station
• TUNED appears when the received signal is strong.
Follow these steps to manually store a station, or to replace a station
already stored in memory.
• STEREO appears when the received FM broadcasts are in
stereo.
1. Press FM or AM on the front panel (or on the remote control) to
select the desired band. The receiver tunes to and displays the
frequency last selected in that band.
• If you press TUNING UP at the top of the frequency range or
TUNING DOWN at the bottom of the frequency range, the
frequency at the opposite end of the range appears.
Note: If CH appears on the right side of the display, press
TUNING MODE to switch to manual-tuning mode. MANUAL
briefly appears.
Direct Tuning (Remote Control Only)
1. Press FM or AM on the front panel (or on the remote control) to
select the desired band. The receiver tunes to and displays the
frequency last selected in that band.
2. Tune to the desired station (see “Manual and Automatic Tuning”
on Page 10).
3. Press MEMORY. MEMORY flashes on the display.
2. Press DIRECT TUNING on the remote control. DIRECT IN
scrolls by, followed by AM – – – – kHz for AM or FM – – – . – –
MHz for FM. The first – flashes.
4. While MEMORY flashes, press TUNING UP or DOWN until the
desired memory channel number appears.
3. Enter the desired frequency using the remote control’s number
buttons.
5. Press MEMORY again to store the station immediately. Or, wait
about 5 seconds and the station is automatically stored in the
selected channel.
Notes:
• If you press 1 to enter a FM frequency, such as 103.5, 10
automatically appears. If you also press the zero, the
frequency that appears would be 100.30.
Notes:
• If you store a frequency in a memory channel that already
contains a frequency, you replace the previous frequency.
• The last zero always appears automatically in both FM and
AM frequencies.
• If your receiver is disconnected from AC power for several days,
it loses all the stored frequencies.
• If you do not press a key within 5 seconds, the receiver exits
direct tuning. Start over at Step 2.
10
• Set the volume to its lowest setting before you begin listening.
After you begin listening, adjust the volume to a comfortable
level.
Tuning to a Station in Memory
1. Press FM or AM on the front panel (or on the remote control) to
select the desired band. The receiver tunes to that band and the
last selected frequency appears.
• Do not listen at extremely high volume levels. Extended high-
volume listening can lead to permanent hearing loss.
Note: If CH does not appear on the right side of the display,
press TUNING MODE to switch to memory-tuning mode.
PRESET briefly appears.
• Once you set the volume, do not increase it. Over time, your
ears adapt to the volume level, so a volume level that does not
cause discomfort might still damage your hearing.
2. Press TUNING UP or DOWN (or PRESET CALL 9 and 8 on
the remote control) to tune to the next higher or lower station
stored in memory.
CASSETTE DECK FEATURES
Or, press PRESET SCAN to scan through the stations in
memory. The receiver tunes to each station for about 5 seconds.
When you hear the station you want to listen to, press PRESET
SCAN again.
You can connect a cassette deck to the receiver. Selecting TAPE
MONITOR lets you hear the playback from the cassette deck you
connected to the receiver’s TAPE MONITOR jacks.
You can also tune to a station in memory by using the remote
control’s number buttons to enter the channel number. For
single-digit channels, enter 0 first (for example, enter 06 for
Channel 6).
Using the Tape Monitor Button
Press TAPE MONITOR. TAPE MON appears, along with the last
program source you selected. You can hear the playback or monitor
a recording from the cassette deck you connected to the receiver’s
TAPE MONITOR jacks.
Notes:
• To improve the reception of weak FM stations, press FM MODE.
This reduces signal noise, but you hear monaural instead of
stereo sound.
The TAPE MONITOR REC jacks continue to output the previously
selected sound source after you press TAPE MONITOR.
• For stations with a weak signal, we recommend manual tuning.
To return to the previous source, press TAPE MONITOR again so
TAPE MON disappears.
ADJUSTING BALANCE
Note: If you press TAPE MONITOR when that cassette deck is
neither playing nor recording, the receiver mutes the current audio
source. To hear the audio source, press TAPE MONITOR so TAPE
MON disappears.
The BALANCE control lets you adjust the sound balance between
the left and right speakers. If you properly position the speakers and
your listening area is centered between them, the center control
setting is usually best (see “Positioning Speakers” on Page 5).
Recording a Program Source
For an unusual speaker placement, press AM to select the AM band
or select any source and play a monaural audio source. Turn
BALANCE until you hear the sound coming equally from each
speaker when you are in the listening area.
The receiver sends the audio of the program source you select—
TAPE MONITOR, AUX, CD, FM/AM (tuner), or PHONO—to the
TAPE MONITOR REC jacks. The VOLUME control does not affect
the level of the signal going to the tape decks.
MUTING THE RECEIVER
When you record a program source using the cassette deck, you hear
the program source’s signal immediately after you record it onto the
tape, if the cassette deck you connected has a three-head monitor
function. (Be sure to read the owner’s manual for your cassette deck.)
To temporarily mute the sound, press MUTING on the remote
control. The MUTE indicator on the receiver flashes. Press MUTING
again to restore the audio level. The MUTE indicator turns off.
USING THE RESET BUTTON
USING HEADPHONES
If the receiver is subjected to a strong magnetic field or an electric
shock, it might operate erratically. If this happens, turn off the
receiver and press the rear panel RESET button with a straightened
paperclip or other pointed object.
To listen with headphones (not supplied), insert the headphones’ 1/4-
inch plug into the receiver’s front panel PHONES jack. To silence the
speakers and listen with headphones without disturbing others,
press SPEAKERS A and/or B so both indicators are off.
Caution: Pressing RESET clears everything stored in the receiver’s
memory.
Listening Safely
To protect your hearing, note the following when using headphones.
11
TROUBLESHOOTING
If the receiver is not working as it should, the following suggestions might help. If you follow the suggestions in this chart and the receiver still
does not work properly, contact your local RadioShack store for assistance.
Problem
Cause
Power cord is disconnected.
Suggestion
Plug in the power cord.
Power does not turn on.
No sound.
Incorrect connections.
Check and correct the connections.
Press MUTING.
The mute function is activated.
The volume is turned down.
Speaker wires are disconnected.
Neither set of speakers is selected.
Turn up the volume.
Connect the speaker wires.
Press SPEAKER A or B.
Both SPEAKER A and B are selected when only one set Press SPEAKERS A or B to turn off the speakers
of speakers is connected. that are not connected.
TAPE MONITOR TAPE MONITOR
is selected.
Press
Check all connections.
so TAPE MON turns off.
Sound from only one speaker.
High noise level.
One of the speaker wires or the input cord is
disconnected.
BALANCE is set too far to one side.
Station not correctly tuned.
Antenna not connected.
Set BALANCE to the center position.
Adjust tuning.
Connect antenna.
FM antenna still coiled or is not pointing in the correct
direction.
Stretch both ends of the antenna taut and reposition
the antenna.
AM loop antenna not pointing in the correct direction.
Noise is coming from another electrical appliance.
Stations are too weak.
Adjust the AM loop antenna.
Try using an AC line noise filter to reduce the noise.
Use a better antenna.
Automatic tuning does not stop when
searching for stations.
Remote control does not work.
Batteries are weak or missing.
Install fresh batteries.
Poor angle or too great a distance from the remote sensor Use the remote within the effective range.
window.
There is an obstacle between you and the remote sensor Change your position or remove the obstacle.
window.
A fluorescent light is shining on the remote sensor
window.
Turn off the light.
12
CARE
Keep the receiver dry; if it gets wet, wipe it dry immediately. Use and
store the receiver only in normal temperature environments. Handle
the receiver carefully; do not drop it. Keep the receiver away from
dust and dirt, and wipe it with a damp cloth occasionally to keep it
looking new.
Modifying or tampering with the receiver’s internal components can
cause a malfunction and might invalidate its warranty and void your
FCC authorization to operate it.
This receiver has been manufactured to the specifications of
RadioShack and is covered by a limited warranty from RadioShack. If
your receiver is not operating as it should, take it to your local
RadioShack store or call 1-800-THE-SHACK for assistance.
13
SPECIFICATIONS
Amplifier
Power Output ................................................................................................................................................. 100 Watts per Channel into 8 Ohms
From 40 to 20,000 Hz,
With No More than 0.5% Total Harmonic Distortion
Measured Pursuant to the Federal Trade Commission’s
Trade Regulation Rule on Amplifier Output Power Claims
Input Sensitivity/Impedance:
Phono .......................................................................................................................................................................................... 2.5 mV/47 kohms
CD, AUX, TAPE MONITOR .................................................................................................................................................... 200 mV/47 kohms
Signal-to-Noise Ratio (IHF, Short-Circuited, A Network):
Phono ............................................................................................................................................................................................................. 72 dB
CD, AUX, TAPE MONITOR ........................................................................................................................................................................ 95 dB
FM Tuner
Frequency Range ............................................................................................................................................................................ 87.5–108 MHz
Usable Sensitivity Mono ................................................................................................................................................................. 15 µV/m, EMF
Signal-to-Noise Ratio:
Mono ...............................................................................................................................................................................................................68 dB
Stereo ............................................................................................................................................................................................................. 63 dB
Distortion Stereo................................................................................................................................................................................. 0.5% (1 kHz)
Alternate Channel Selectivity ........................................................................................................................................................................ 45 dB
Stereo Separation .............................................................................................................................................................................. 35 dB (1 kHz)
AM Tuner
Frequency Range ............................................................................................................................................................................. 530–1720 kHz
Sensitivity (IHF, Loop Antenna) ............................................................................................................................................................. 500 µV/m
Selectivity ...................................................................................................................................................................................................... 25 dB
Signal-to-Noise Ratio .................................................................................................................................................................................... 35 dB
General
Power Requirements .............................................................................................................................................................. 120 Volts AC, 60 Hz
Power Consumption ................................................................................................................................................................................ 190 Watts
Dimensions (HWD) ............................................................................................................. 511/16 × 169/16 ×137/16 Inches (144 × 420 × 321 mm)
Weight ............................................................................................................................................................................................... 14 lb (6.3 kg)
Specifications are typical; individual units might vary. Specifications are subject to change and improvement without notice.
14
NOTES
15
Limited Two-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for two (2) years from the date of purchase from RadioShack company-
owned stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED
HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES,
INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES
CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABIL-
ITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RE-
SPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE
OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WAR-
RANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVE-
NIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT,
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN AD-
VISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limita-
tion of incidental or consequential damages, so the above limitations or exclusions may not apply to
you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
12/99
RadioShack Corporation
Fort Worth, Texas 76102
31-5006
01A02
Printed in China
|