R
PLCD41MP
CD/MP3PLAYER......
WNER'S MANUAL
C
a
r
A
u
d
i
o
H
i
f
i
S
y
s
t
e
m
A M / F M R E C E I V E R
To prevent injury or fire,take the
following precautions:
To prevent damage to the machine,
take the following precautions:
Attaching panel
Attach the front panel by fixing
the left side of it into this unit as1
showing.Then push the right side
of panel towards into connecting
plug as 2 showing.
Insert the unit until it is firmly locked to the
main unit, otherwise it may
Be sure the unit is connected to a 12V
DC power with a Negative Ground
fall out of place when jolted
The unit is only designed for use with 4
speakers. Do not combine output for use
with 2 speakers. Do not ground negative
speaker leads to the chassis ground
Do not open the top cover and do not install
the unit in
When extending the ignition, memory
back up or ground cable, use diameter of
0.75mm(AWG18) or
more automotive grade cable to avoid wire
deterioration or damage
to the wire coating.
place where it is exposed to direct sunlight
(including the faceplate),in order to avoid high
heat or humidity, water splash over it or dust.
Do not touch the terminals of the units.
Attaching panel
To prevent short circuit, never put or leave
any metallic object into the unit.
If you smell or see smoke, turn off the
power immediately and consult your dealer.
Be careful not to drop or shock the unit
strongly, it may break or crack because it
contain glass parts.
If you have difficulty in installing this unit
in your vehicle. Please contact your dealer.
If the unit seems not work in properly press
the reset buttonto reset the memory of the
unit.
2
Follow this easy wiring diagram in order to enable you to install
the new or existing RADIO and SPEAKER wring system.
SPEAKER WIRING
The unit is only designed for the use with 4 speakers system, it can
only be connected with speakers rated in the load impedance range
from 4 to 8 ohms. Load impedance less than 4 ohms could damage
the unit.
Be sure the unit is connected to a 12 volts battery with negative ground.
Good ground connections eliminate most electrical noise problem and
require tight with the metal vehicle chassis. remove plastic, paint or dust
for good electrical contact.
Never combine (BRIDGE) the outputs for use with 2 speakers, and
Never ground any Negative speaker to the chassis ground.
Subwoof
CAR ANTENNA
RED RCH
CAR ANTENNA
RED RCH
LCH RCA line out
RED RCH
WHITE
Auxin
WHITE LCH
RCA line out
WHITE LCH
Connect to control for antenna
or remote control for amplifier.
Orange
Memory+
YELLOW
Grey
Green
Connect to battery or +12 volts of
power source that is always live.
Green
/white
Grey
/white
Black
Red
Ground-
Right Front
Left Front
Brown
Blue
12V+
Brown
/white
Blue
/white
Connect to lgnition key switch.
Right Rear
Left Rear
3
Before installing the receiver permanently, fit it in the approximate place in your car Connect the
equipment according to the speakers and electrical connections. When
your system is operated properly,(preferably with the
car engine running), follow the instructions
for permanent installation
of your system.
3)Support strap
(supplied)
INSTALL THE UNIT
1)Install half sleeve, can be with or
without adapter. It will fit better
with adapter.
2)Bend over some tabs where possible
2)Bend over tabs
of half sleeve
(supplied)
tosecure the half sleeve inside of dash.
3) Support strap to bestrutted under
dash, secure this strip to avoid skipp
ing of disc.
1) Adapter
(not supplied)
Half sleeve
(supplied)
REMOVING THE UNIT
Insert removal wrench into the small
gap on the right side of the unit and pull
the unit slightly out on the same side,
then release the wrench. Repeat the
same action for the left side. By now,
you can remove the unit and unplug
the wires connector.
4) Two wrenches for release
the unit (supplied)
4
Volume
POWER ON
/OFF
EJECT
Increasing volume
VOLUME
Rotate the [VOL+]button
PWR
VOL
Decreasing
VOL
SEL
Rotate the [VOL-]button
SEL
SEEK
SCN
2
RPT
3
SHF
4
BAND CLOCK MODE
DSP
1
5
6
SELECT
DSP
CLOCK
RELEASE
MODE
Eject
ST
LOUD
LOC
Out
CH
Press the [ ]button to eject the disc out of the unit .
LCD display
In
Power
Press the [ ]button again,
to load the disc in.
Turning ON the power
Press the [PWR]button.
EJECT
Press to turn on the unit power,Press the button to turn off
the unit.
5
Hour
MODE
Press [
Minute
] button to set the hour.
Selecting radio and play
Press the [MODE]key.
Press [ ] button to set the minute.
Each time you press the key, it`ll switch between radio
and CD position.
Quit clock set mode
It will quit clock set mode If there is no operation
in 5 seconds.
(If mode with AUX IN,the function is below:
press MD(MODE)to select:
1
If with DISC,press MD that is:
AUX IN
RADIO
DISC
AUX IN
Dsp
2
If without DISC,press MD that is:
Short press this button to DSP
AUX IN
RADIO
AUX IN
Press LOUD button once, ROCK will bicker on display.
Press LOUD button twice, POP will bicker on display.
Press LOUD button third, CLASS will bicker on display.
Band(Loud)
DSP
LOUD
Release
Long press the [BD/LD]button to emphasize the bass output,
Long press it again to resume the normal listening.
press the "
" button to release faceplate.
Clock
Short press CLK can display time even power off .
Long Press CLK for 3 seconds will enter set mode.
6
SELECT
Speaker mode
PWR
VOLUME
TREBLE
BASS
VOL
SEL
SEEK
SCN
2
RPT
3
SHF
4
BAND CLOCK MODE
DSP
1
5
6
FADER
BALANCE
SHF
DSP
SCAN
PLAY/PAUSE
VOLUME
REPEAT
In press mode, VOL is sel function
Treble set mode
Volume set mode
Press SEL button third,
display shows TRE ,then
rotate the volume
level up. Rotate the volume
treble level down.
TRE
5
Press SEL button once,display shows VOL
then rotate the volume button
to adjust volume level up.rotate
the volume button to
,
+
+
button to adjust treble
-
button to adjust
-
VOL
adjust volume
level down.
SEL
Balance set mode
Press SEL button fourth
display shows BAL ,then
PRESS
VOL 10
rotate the volume
to adjust right speaks level .
Rotate the volume button
to adjust left speaks level .
+
button
BAL
4
Bass set mode
-
Press SEL button twice,display shows BAS
then rotate the volume button to adjust bass
button to adjust
,
+
level up. rotate the volume
bass level down.
-
Fader set mode
Press SEL button fifth,display shows FAD ,then
rotate the volume button to adjust rear speaks
+
BAS -6
level. Rotate the volume
speaks level.
-
buttonto adjust front
FAD -3
7
Play/pause
Shf
Pause
Press [SHF]button
If with DISC in unit,Press the [
]to pause music.
Press [SHUF] button to play all the track in random order.
SHF and playing song number will appear on the LCD.
Press [SHUF]again will stop random playing.
Play
Press the [
DISC playing.
]button again ,then come back to
Scan
Press [SCN]button
Press this button once for TRACK INTRODUCTION.
The first 10 seconds of each track on the disc will play. And the
track number shows on LCD.
To select a desired song, press [SCN]button while it is playing.
Repeat
Press [RPT]button
REPEAT
Press [REPEAT] button to repeat the track continuously.
RPT and the playing song number will appear on the LCD.
Press [REPEAT] again will be back to normal playing.
8
Tuner
In radio mode:
PWR
manual tuning:
VOL
SEEK-
short press
Short press
button it can select higher frequency station.
can select lower frequency station.
SEL
SEEK
SEEK+
SCN
2
RPT
3
SHF
4
BAND CLOCK MODE
DSP
1
5
6
Auto loading tuning:
the long press
button it can automatically select higher
PRESET MEMORY 1-6
BAND
frequency station. And the long press
select lower frequency station.
it can automatically
Band
Selecting band
Preset memory
Press BAND button to select among three FM or two AM bands.
(FM1-FM2-FM3-AM)
Manual Preset Station
Please keep pressing any of the No.1-6 button to store when you
hear the favorite broadcasting station.
FM1
AM
FM2
FM3
Automatic Preset Station
In any band play, keep pressing AS/PS on the remote control into
automatic storage. And 6 powerful stations in this band will be stored
into NO.1-6 respectively.
There are 6 bands for selection:FM1,FM2,FM3,AM.Make selection
by pressing BAND Button.
If with DISC in unit, press [MODE] switch to radio MODE first.
Selecting and pressing the buttons stored,you can play the station
you want then.
9
Loading and replacing the battery
MODE
MUTE
Use one lithium battery(CR2025)
insert the batteries with the +and - poles aligned properly.
Following the illustration inside the case.
PWR
MODE
BAND
POWER
SCAN
MUTE
BAND/LOUD
REPEAT
STU7
ENTER
-,_,+,0
LOUD
AS/PS
1
2
3
PAUSE
AS/PS
ABC
DEF
GHI
ID3
PAUSE
RPT
SCAN
4
5
6
LOC
LOCAL
MONO
SHUF
DSP
JKL
MNO
PQR
SHF
DISC DN
DISC UP
+
DSP
RO/SN
MONO
CHAR.SEL
VOL+/CHAR.SEL
SEL
SHIFT
VWX8
YZ9
Pull out
SPACE
SELECT
CLK
CHAR.SEL
Store unused batteries out of the reach of children. Contact a
doctor immediately if the battery is accidentally swallowed.
Do not set the remote on hot places such as above the dashboard.
_,-,+,0,PWR
Mode select
LOC
MUTE
Basic operation
DSP
S,T,U, ,MODE
Enter,BAND
Char.sel(A,B~8,9,0),+/-
RADIO.SCAN
MONO
Turning ON the power
A,B,C,1,PAUSE
D,E,F,2,SCAN
Press the [PWR]button.
G,H,I,3,REPEAT
J,K,L,4,SHUF
Y,Z, ,space,
V,W,X,
Press to turn on the unit power,Press the button to turn off
the unit.
M.N,O,5,DISC DN
P,Q,R,6,DISC UP
Char.shift,SEL
CLK
10
External view
........ Number of items
External view
........ Number of items
ID3
MUTE
MODE
BAND
LOUD
AS/PS
Press ID3 on remote or Panel enter ID3 selection.
one press ID3 enter ID3 file selection mode, F will be indicated on
LCD.
P
AUSE
SCAN
RPT
LOC
SHF
DSP
DISC DN
DISC UP
RO/SN
MONO
............1
............1
............1
1
2
5
6
7
SEL
CLK
To read in your desired song name by pressing remote ABC
BAND
-
buttons,
YZ9
ENTER
then press confirmed the song playing.
EXAMPLE: to read in " I LOVE YOU"
In the read in mode: press
............1
............1
............2
YZ9
button three times read I, press turn
GHI
to next word,press
O and so on...
Two press ID3 enter ID3 directory mode,D will be indicated on LCD.
three times read L,press three times read
MNO
JKL
BAND
ENTER
select desired directory,then press confirmed playing.
Press
/
YZ9
VWX8
3
4
............1
In read in song name mode, press
press
YZ9
clear wrong written words.
SPACE
turn to next word.
ID3 only value as MP3 disc in.
The use of any accessories except of those provided
might result in damage to the unit .make sure only to
use the accessories shipped with the unit ,as shown
above.
Other function
Please refer to panel.
Remote operation the same
of mainframe.
11
Specifications subject to change without notice.
CD PLAYER
GENERAL
Signal/Noise radio......................................................70dB
Frequency response..............................20Hz-20KHz(+3dB)
Channel separation..................................................>45dB
Dual D/A converter.......................................................16Bit
Operating power.....................................12 Volts DC,negative
ground
%10THD output wiring.........................Designed for using four
speakers only front and rear
channels cannot be combined
in use with 2speakers.
FM Tuner
Load impedance..................................compatible 4 to 8 ohm
speakers
Tuning range............................................USA:87.5-108MHz
(100KHz step)
Fuses........................................................1amp and 10 amp
Dimensions...........................................178mm(L)x50mm(W)
x150mm(H)
EUROPE:87.5-108.0MHz
(50KHz step)
FM usable sensitivity(S/N=30dB)..............................<12dB
Stereo separation.....................................................>45dB
Weight......................................................................2.5Kgs
AM Tuner
Tuning range...........................................USA:520-1620KHz
(10KHz step)
EUROPE:522-1620KHz
(9KHz step)
AM sensitivity..............................................................28dB
12
What might seem to be a malfunction in your unit may
just be the result of slight misoperation or miswiring.
Before calling service, first check the following table
for possible problems.
?No/Poor sound on one or more speakers
Speakers or speaker wiring or volume, Balance and
Fader setting
Check the speaker wiring and test the speakers all in good condition
check the setting of volume, Balance and Fader controls.
?The power does not turn ON.
The fuse has blown.
Install half sleeve, can be with or
?CD sound skips
Installation the unit angle is greater than 45 ,or
mounting is not fixed and the back strap is not secure.
?NO Sound.
The cable connect incorrectness.
Adjust the unit with mounting angle less than 45 and make sure the
unit is mounted securely and tighten with the back strap(supplied)
Exactitude connect of the cable.
?Noise on Radiopoor recepiton
?Unit completely inoperative, no Light and Sound
Antenna and Antenna Cable.
Incorrect wire connection, Power RED/YELLOW or
Ground wire or Blown fuse
Check antenna and antenna cable, the antenna base must be
grounded and connected with good condition, repace
antenna or antenna cable if needed.
Check the Red wire to +12 Volts with key lgnition witch, yellow wire to
+12 Volts battery and black wire to ground. Check Fuse with red/yellow
wire, or check the fuse block on your car.
?Noise on both Radio and CD
Poor ground,dirty or corroded at the car Battery posts
Check the black wire for proper grounding clean and tighten ground
connection.
13
A M / F M R E C E I V E R
W I T H E S P F O R C D 4 0 S , M P 3 7 0 - 1 2 0 S
C
a
r
A
u
d
i
o
H
i
f
i
S
y
s
t
e
m
|