Radio Shack Music Mixer 32 2056 User Guide

Thank you for purchasing your Stereo 4-Channel  
Microphone Mixer from RadioShack. It enables you  
to mix and add sound from up to four microphones or  
two audio input sources, such as a CD player, tuner,  
or cassette player. Please read this users guide before  
installing, setting up and using your new product.  
32-2056  
Stereo • 4-Channel  
Microphone Mixer  
What’s Included  
Mixer  
User’s Guide  
Specifications  
Connections  
AUX2 L and R AUX1 L and R  
Input Sensitivity:  
Mic ...................................................................................... 1.5 mV/600 ohm  
Line ..................................................................................... 150 mV/27k ohm  
Output Level at 10k Ohm Load............................................................. 1.2V  
Input Overload:  
Mic ....................................................................................more than 250 mV  
Line ...........................................................................................more than 6V  
Distortion.................................................................................less than 0.2%  
Signal-to-Noise Radio......................................................better than 60 dB  
Frequency Response.................................................. 10~35,000 Hz 3 dB  
Power Requirements:  
DC..........................................................................................One 9V battery  
AC Adapter .............................................................Output: 9VDC, 100 mA  
.....................................................................................Input: 120V AC, 60 Hz  
Dimensions (H×W×D) ................................... 2 3/16 × 10 5/8 × 6 5/16 inches  
.......................................................................................... (5.5 × 27 × 16 cm)  
Weight ........................................................................... 1 lb 10.5 oz. (850 g)  
BATTERY LOW  
Indicator  
OUTPUT L and R  
POWER Switch  
MONO/STEREO  
Use shielded audio cables (not supplied) for all input  
connections. The connected input sources signals are  
routed to the corresponding channel on the mixer.  
Two stereo inputs  
Connect the line level outputs from one device to the  
mixers AUX 1 INPUT R and L jacks. Connect the line level  
outputs from the second device to the mixers AUX 2  
INPUT R and L jacks.  
Specifications are subject to change and improvement without notice.  
Actual product may vary from the images found in this document.  
Recycle Rechargeable Batteries  
Placing rechargeable batteries in the trash can be harmful to the  
environment. Instead, recycle old rechargeable batteries at your  
local RadioShack store free of charge. RadioShack participates  
in the RBRC© battery recycling program, and is committed to  
preserving the environment and conserving natural resources. Call  
1-800-THE-SHACK (1-800-843-7422) for more information.  
Four stereo sources as monaural inputs  
Use shielded Y-adapters (not supplied) at each sources left  
and right outputs, and connect a separate stereo source to  
each input jack (AUX 1 R, AUX 1 L, AUX 2 R, or AUX 2 L)  
on the mixer.  
Limited Warranty  
CHANNEL 1-4  
Four monaural inputs  
This product is warranted by RadioShack against manufacturing defects in  
material and workmanship under normal use for one (1) year from the date of  
purchase from RadioShack company-owned stores and authorized RadioShack  
franchisees and dealers. EXCEPT AS PROVIDED HEREIN, RadioShack MAKES  
NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING  
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,  
ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED  
WARRANTIES CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN,  
Connect each monaural device to each input jack (AUX 1 R,  
AUX 1 L, AUX 2 R, or AUX 2 L) on the mixer.  
Setting Up Your Mixer  
Installing Batteries  
1. Remove the battery cover.  
2. Insert one 9V battery (not  
supplied) in the battery  
Two monaural sources as stereo inputs  
Notes:  
Use shielded Y-adapters (not supplied) at each sources  
monaural outputs, and connect one source to AUX 1 R and L.  
Connect the other source to AUX 2 R and L.  
Always connect the AC adapter to the mixer before you  
connect it to AC power. When you finish, disconnect the  
adapter from AC power before you disconnect it from the  
mixer.  
RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER  
OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS  
OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE  
OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY,  
INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM  
INCONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR  
ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN  
IF RadioShack HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.  
Using an adapter that does not meet the specifications could  
damage the mixer or adapter.  
compartment matching  
the polarity symbols (+ and  
–) marked on the back of the  
battery cover.  
Some states do not allow limitations on how long an implied warranty lasts or  
the exclusion or limitation of incidental or consequential damages, so the above  
limitations or exclusions may not apply to you.  
Presetting the Mixer  
In the event of a product defect during the warranty period, take the product  
and the RadioShack sales receipt as proof of purchase date to any RadioShack  
store. RadioShack will, at its option, unless otherwise provided by law: (a) correct  
the defect by product repair without charge for parts and labor; (b) replace the  
product with one of the same or similar design; or (c) refund the purchase price.  
All replaced parts and products, and products on which a refund is made, become  
the property of RadioShack. New or reconditioned parts and products may be  
used in the performance of warranty service. Repaired or replaced parts and  
products are warranted for the remainder of the original warranty period. You will  
be charged for repair or replacement of the product made after the expiration of  
the warranty period.  
This warranty does not cover: (a) damage or failure caused by or attributable to  
acts of God, abuse, accident, misuse, improper or abnormal usage, failure to  
follow instructions, improper installation or maintenance, alteration, lightning  
or other incidence of excess voltage or current; (b) any repairs other than those  
provided by a RadioShack Authorized Service Facility; (c) consumables such as  
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance  
costs; or (f) costs of product removal, installation, set-up service adjustment or  
reinstallation.  
To prevent accidental audio mixing or channel overdrive,  
set MONO/STEREO to MONO, set POWER ON/OFF to  
OFF, and slide Channel 1–4 to 0 (minimum) before you  
connect to your power supply.  
3. Replace the battery cover.  
MIC jacks  
Four microphones  
Replace the battery when BATTERY LOW indicator lights.  
Connect up to four microphones to the mixers MIC jacks  
(14). Each microphone signal is routed to the mixers  
corresponding channel.  
Battery Notes  
Dispose of old batteries promptly and properly.  
Do not burn or bury batteries.  
A sudden high output from the mixer could damage audio  
devices connected to the mixer and could damage your  
hearing, especially if you use headphones.  
If you connect an audio device and a microphone so they  
are output to the same channel, the signals from both  
devices are mixed and controlled by the mixer.  
Use only a fresh battery of the required size and recommended  
type.  
If you do not plan to use the mixer for more than a week,  
remove the battery. It can leak chemicals that can damage  
electronic parts.  
Presetting Audio Devices  
Make sure you power off the devices before you connect  
them to the mixer.  
Output  
To play the mixers output through your speaker system (at  
parties, dances, conferences, etc.), use an audio patch cord  
(not supplied) to connect the mixers OUTPUT L and R jacks  
to your receiver or amplifiers line input jacks.  
To record the mixers output, use an audio patch cord (not  
supplied) to connect the mixers OUTPUT L and R jacks to  
your recording devices line input jacks.  
This warranty gives you specific legal rights, and you may also have other rights  
which vary from state to state.  
RadioShack Customer Relations  
300 RadioShack Circle, Fort Worth, TX 76102  
Using AC Power  
Connect a 9V AC adapter (not  
supplied) to the DC 9V jack.  
Connect the other end to the  
power source.  
12/99  
To avoid sudden sound outputs from connected audio  
devices, adjust the volume of the connected audio device  
to its lowest level.  
Protect the environment by recycling used electronics. Go to  
DC 9V  
©2008. RadioShack Corporation.  
08A08  
All rights reserved. RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.  
32-2056  
Printed in China  
 

Quantum Barcode Reader 6 01658 01 User Guide
Rowenta Iron DX1900 User Guide
Ryobi Router RE601 User Guide
Ryobi Trimmer 225RD User Guide
Saint Gobain Vidros Water Pump PFD4 User Guide
Samson DJ Equipment XP510I User Guide
Samson Musical Instrument PL1602 User Guide
Samsung Computer Hardware 35 hard disk drives User Guide
Samsung Network Router SWL 2200U User Guide
Sears Sewing Machine 385 1884180 User Guide