12 Memory Fashion
Desktop Phone
If you use more than one phone or other de-
vice on the line, add up all of the RENs. If the
total is more than five (or three in rural ar-
eas), your telephones might not ring. If ringer
operation is impaired, remove a device from
the line.
your phone company. These numbers are
shown on the bottom of the base.
Note:
You must not connect your phone to
any of the following:
• coin-operated systems
• party-line systems
FCC STATEMENT
This telephone complies with Part 68 of FCC
Rules. You must, upon request, provide the
FCC Registration Number and the REN to
• most electronic key phone systems
Your phone is ETL listed to UL standards
and meets all applicable FCC requirements.
ˆ Preparation
2. Plug the other end of the modular cord
into a modular phone jack.
MOUNTING THE PHONE
You can mount your telephone on a desktop,
on a standard wall plate, or directly on a wall.
3. Place the phone on a flat surface such
as a desk, shelf, or table.
Choose a location for the phone that is:
• not in the way of normal activities
• near a modular telephone line jack
On a Wall Plate or Wall
Follow these steps to mount the phone on a
standard wall plate or wall.
Your telephone connects directly to a modu-
lar telephone line jack. If your telephone wir-
ing does not have a modular jack, you can
update the wiring yourself using jacks and
adapters (available at your local RadioShack
store), or have the telephone company up-
date the wiring for you. You must use com-
patible modular jacks that are compliant with
Part 68 of FCC Rules.
1. Plug one end of the supplied modular
TEL LINE
cord into the
jack on the back
of the telephone.
2. Insert the mounting bracket’s tabs into
the slots on the bottom of the telephone.
Then route the modular cord through the
bracket and push the bracket up until it
snaps into place.
Note:
The USOC number of the jack to be
installed is RJ11C (or RJ11W for a wall plate
jack).
On a Desktop
1. Plug one end of the supplied modular
TEL LINE
cord into the
of the phone.
jack on the back
3
Preparation
3. Plug the other end of the modular cord
into the wall plate’s modular jack.
SETTING THE RINGER
VOLUME AND RING TYPE
4. Align the bracket’s keyhole slots with the
wall plate studs and slide the base
downward to secure it on the wall plate.
Your phone comes with a preset ringer.
However, you can choose from three differ-
ent types of ring signal and set the ringer vol-
ume to high, middle, low, or off. Follow these
steps to set the ringer type and volume level:
Note
: To mount the phone directly on a wall,
you need two screws (not supplied) with
heads that fit into the keyhole slots on the
bottom of the phone and bracket.
1. Pick up the handset.
STORE/MUTE
2. Press
.
#
3. Press .
Select and press a number 0–9 (see table
below) to set the ringer type and volume.
Digit
Ringer Type
Ringer Volume
Low
1
2
3
4
5
6
7
8
9
0
Music
Follow the steps under “On a Wall Plate or
Wall” on Page 3, then follow these additional
instructions for placement on a wall.
Music
Middle
High
Low
Music
Standard
Standard
Standard
Quick
1. Drill two holes 315/16 inches (100 mm)
apart. Then thread a screw into each
Middle
High
Low
3
hole, letting the head extend about /16
inches (5 mm) from the wall.
Quick
Middle
High
Off
2. Align the bracket’s keyhole slots with the
mounting screws and slide the bracket
down to secure it.
Quick
No ring
CONNECTING THE
HANDSET CORD
STORE/MUTE.
4. Press
5. Return the handset to the cradle.
1. Plug one end of the supplied coiled cord
into the handset’s modular jack.
Note:
If you choose to turn the ringer off by
selecting digit 0, the next time you pick up
the receiver, the ringer will reset to the previ-
ous setting.
2. Plug the other end of the coiled cord into
the handset jack on the left side of the
phone nearest the handset cradle.
SETTING THE DIALING
MODE
3. Place the handset on the cradle.
Note:
Your local RadioShack store carries
TONE/PULSE
Set
for the type of service you
several different lengths and colors of phone
cords that are especially useful when wall-
mounting the phone.
have. If you are not sure which type you
have, do this test.
4
Preparation
TONE/PULSE
TONE
Note:
If you have pulse service and
1. Set
to
.
want to use a special service that
requires tone signals (such as bank by
phone), see “Using Tone Services on a
Pulse Line” on Page 6.
ADJUSTING THE RECEIVER
VOLUME
TONE/PULSE
Set the receiver volume as follows:
2. Pick up the handset. When you hear the
dial tone, press any number other than
1. Pick up the handset.
0
.
VOLUME UP
2. Press
3. Press
to increase the
to decrease the
Note:
If your phone system requires that
receiver volume.
9
you dial an access code ( , for example)
before you dial an outside number, do
not press the access code number.
VOLUME DOWN
receiver volume.
3. If the dial tone stops, you have touch-
4. Return the handset to the cradle.
TONE/PULSE
tone service. Leave
set to
Note:
You can also adjust the volume during
TONE
.
a telephone conversation.
If the dial tone continues, you have
TONE/PULSE
pulse service. Set
to
PULSE
.
ˆ Operation
STORE/MUTE
Press
again to resume your
PLACING A CALL
phone conversation.
Lift the handset and dial the number.
Note:
You can reactivate the microphone by
M1
pressing any functional button, except
,
USING REDIAL
M2
#
, and . You will hear three beeps through
the handset’s receiver to indicate that the mi-
crophone is working.
To redial the last number dialed (up to 31
REDI-
digits), pick up the handset and press
AL
.
USING FLASH
USING MUTE
FLASH
Use
to perform the switchhook oper-
ation for special services, such as Call Wait-
ing.
To talk to someone in the room without the
person on the other end of the phone line
STORE/
hearing your conversation, press
MUTE
For example, if you subscribe to Call Wait-
ing, you can put your current call on hold and
answer another call on hold. You can also
. The STORE/MUTE indicator flashes.
5
Operation
STORE/MUTE
. The STORE/MUTE
answer another call on the same line by
2. Press
FLASH
FLASH
again to alter-
pressing
, press
indicator flashes.
nate between the two calls.
3. Press the direct memory location key
Note:
M1
M2
or ).
If you do not have Call Waiting, press-
(
FLASH
ing
might disconnect current call.
4. Dial the number you want to store in
memory (up to 21 digits).
USING TONE SERVICES ON
A PULSE LINE
STORE/MUTE
5. Press
. The STORE/MUTE
indicator turns off. Return the handset to
the cradle.
Some special services, such as bank by
phone, require tone signals. If you have
pulse service, you can still use these special
tone services by following these steps.
Storing a Phone Number Into an
Indirect Memory
TONE/PULSE
PULSE
,
1. Set
on the back to
1. Pick up the handset.
then call the special service.
STORE/MUTE
2. Press
so the STORE/
2. When the service answers, press *.
MUTE indicator flashes.
3. Any additional numbers you dial are
sent as tone signals.
MEMORY,
3. Press
then enter the desired
0 9
memory location ( – ).
4. Follow the normal procedures for the
special service you are using.
4. Dial the number you want to store in
memory (up to 21 digits).
5. When you complete the call, place the
handset on the base to disconnect the
call. The phone automatically resets to
the pulse mode.
STORE/MUTE
5. Press
so the STORE/
MUTE indicator turns off. Return the
handset to the cradle.
Dialing a Memory Number
1. Pick up the handset.
MEMORY DIALING
M1
M2
)
There are two direct memories (
and
0 9
and ten indirect memory locations ( – ) for
storing frequently used phone numbers.
2. To dial a number from a direct memory,
M1
M2
.
press
or
The phone does not need batteries for back-
up memory. If the telephone line is discon-
nected, the phone retains numbers in
memory for up to 2 minutes.
To dial a number from an indirect mem-
ory, press MEMORY then 0–9.
Using The Memory Card
Storing Numbers Into Direct
Memories
To keep a record of numbers you have
stored in the phone’s direct and indirect
memories, lift off the clear plastic cover over
the memory card, then write the person’s or
company’s name next to that number on the
memory card. There is also a quick refer-
Follow these steps to store numbers into the
two direct memory locations:
1. Pick up the handset.
6
Operation
ence list that offers brief phone operating in-
structions on the back cover of the memory
card. To view it, lift off the memory card.
When you have finished using the memory
card, replace it and then replace the clear
plastic cover.
LIGHTNING
Your telephone has built-in protection circuits
to reduce the risk of damage from surges in
telephone line current. However, lightning
striking the telephone line can damage your
telephone.
CARE
Lightning damage is not common. However,
if you live in an area that has severe electri-
cal storms, we suggest you unplug your
phone when storms approach to reduce the
possibility of damage.
To enjoy your phone for a long time, keep it
dry. If it gets wet, wipe it dry immediately.
Use and store the phone only in normal tem-
perature environments. Handle the phone
gently and carefully; do not drop it. Keep the
phone away from dust and dirt. Wipe the
phone with a damp cloth occasionally to
keep it looking new.
Modifying or tampering with the phone’s in-
ternal components can cause a malfunction
and might invalidate its warranty and void
your FCC authorization to operate it. If your
phone is not working properly, take it to your
RadioShack store for assistance. If the trou-
ble is affecting the telephone lines, the
phone company can ask you to disconnect
your phone until the problem is resolved.
THE FCC WANTS YOU TO
KNOW
In the unlikely event that your phone causes
problems on the phone line, the phone com-
pany can temporarily discontinue your ser-
vice.
If this happens, the phone company attempts
to notify you in advance. If advance notice is
not practical, the phone company notifies
you as soon as possible and advises you of
your right to file a complaint with the
FCC. Also, the phone company can make
changes to its lines, equipment, operations,
or procedures that could affect the operation
of this telephone. The telephone company
notifies you of these changes in advance, so
you can take the necessary steps to prevent
interruption of your telephone service.
7
Operation
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limita-
tion of incidental or consequential damages, so the above limitations or exclusions may not apply to
you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the property
of RadioShack. New or reconditioned parts and products may be used in the performance of war-
ranty service. Repaired or replaced parts and products are warranted for the remainder of the origi-
nal warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
12/99
12A00
43-3205/3230/3231
Printed in China
|