900MHz Hands-free Phone
with Caller ID/Call Waiting
43-3906
Lapel Clip — lets you securely anchor the
headset’s cord to your clothing to prevent the
headset cord from pulling on the headset, and
to keep the cord out of the way.
10-Number Memory Dialing — lets you
store up to 10 numbers in memory for easy
dialing.
30-Record CID Capacity — stores up to 30
call records in Caller ID.
Ample Talk and Standby Time — the
supplied battery (when fully charged)
provides about 7 hours of talk time or 14 days
of standby time.
Auto Talk — lets you set the phone to
answer a call by simply lifting the handset
from the base.
IMPORTANT
!
!
If an icon appears at the end of a paragraph, go to the box on that page
with the corresponding icon for pertinent information.
— Important !— Caution Ó — Hint Ô — Note
o— Warning
!
OWNER’S MANUAL
Please read before using this equipment.
© 2003 RadioShack Corporation.
All Rights Reserved.
RadioShack and RadioShack.com are trademarks
used by RadioShack Corporation.
ENERGYSTAR and the ENERGYSTAR certification
mark are registered US marks
must provide the phone’s FCC
registration number and REN to your
phone company. These numbers are
on the base unit.
CONTENTS
(Continued)
Selecting the
Channel ............... 23
Adjusting the
Headset’s
Volume ................ 23
Using Redial ........ 23
Using Flash ......... 24
Muting the
Ringer .................. 24
Using Tone Services
on a Pulse Line ... 24
Paging ................. 25
Memory Dialing ... 25
Speed Dialing ...... 32
Caller ID Operation . 33
Important Caller ID
Information .......... 34
Reviewing Caller ID
Records ............... 35
Adding/Deleting the
Area Code ........... 36
Dialing Numbers
Your phone is not intended to be used
with party-line systems. Connection to
party line service is subject to state
tariffs. Contact the state public utility
commission, public service
commission, or corporation
commission for information.
We have designed your phone to
conform to federal regulations, and you
can connect it to most telephone lines.
However, each phone (and each
device, such as a telephone or
answering machine) that you connect
to the telephone line draws power from
the telephone line. We refer to this
power draw as the device’s ringer
equivalence number, or REN on the
back of your phone.
from a Caller ID
If you use more than one phone or
other device on the line, add up all of
the RENs. If the total is more than five
(three in rural areas), your telephones
might not ring. If ringer operation is
impaired, remove a device from the
line.
Record ................. 37
Storing a Caller ID
Record in
Memory ............... 37
Deleting Caller ID
Records ............... 38
Troubleshooting ...... 40
Care ........................ 43
Service and Repair . 43
In the unlikely event that your phone
causes problems on the phone line, the
3
phone company can temporarily
discontinue your service. If this
happens, the phone company attempts
to notify you in advance. If advance
notice is not practical, the phone
company notifies you as soon as
possible and advises you of your right
to file a complaint with the FCC.
Ô NOTE Ô
You must not connect
your phone to:
•
coin-operated
systems
•
most electronic key
telephone systems
Also, the phone company can make
changes to its lines, equipment,
operations, or procedures that could
affect the operation of this phone. The
telephone company notifies you of these
changes in advance, so you can take
the necessary steps to prevent
interruption of your telephone service.Ô
SURGE PROTECTION
Your phone has built-in protection
circuits to reduce the risk of damage
from surges in telephone line and
power line current. These protection
circuits meet or exceed the FCC
requirements. However, lightning
striking the phone or power lines can
damage your phone.
Lightning damage is not common.
Nevertheless, if you live in an area that
has severe electrical storms, we
suggest that you unplug your phone
when storms approach to reduce the
possibility of damage.
4
IMPORTANT SAFETY
INSTRUCTIONS
When using your telephone equipment,
basic safety precautions should always
be followed to reduce the risk of fire,
electric shock and injury to persons,
including the following:
1. Read and understand all
instructions.
2. Follow all warnings and
instructions marked on the
product.
3. Never install telephone wiring
during a lightning storm.
4. Never install telephone jacks in
wet locations unless the jack is
specifically designed for wet
locations.
5. Never touch uninstalled telephone
wires or terminals unless the
telephone line has been
disconnected at the network
interface.
6. Use caution when installing or
modifying telephone lines.
7. Do not fix the AC power supply
cord to building surfaces with
metal fittings (if the product has an
AC power cord).
5
8. Unplug this product from the wall
outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
9. Do not use this product near water,
for example, near a bathtub, wash
bowl, kitchen sink, or laundry tub,
in a wet basement, or near a
swimming pool.
10. Do not place this product on an
unstable cart, stand, or table. The
product may fall, causing serious
damage to the product.
11. Slots and openings in the cabinet
and the back or bottom are
provided for ventilation. To protect
it from overheating, these
openings must not be blocked or
covered. The openings should
never be blocked by placing the
product on a bed, sofa, rug, or
other similar surface. This product
should never be placed near or
over a radiator or heat register.
This product should not be placed
in a built-in installation unless
proper ventilation is provided.
12. This product should be operated
only from the type of power source
indicated on the marking label. If
you are not sure of the type of
6
power supply to your home,
consult your local power company.
13. Do not allow anything to rest on the
power cord. Do not locate this
product where the cord will be
stepped on.
14. Do not overload wall outlets and
extension cords as this can result
in a risk of fire or electric shock.
15. Never push objects of any kind into
this product through cabinet slots
as they may touch dangerous
voltage points or short out parts
that could result in a risk of fire or
electric shock. Never spill liquid of
any kind on the product.
16. To reduce the risk of electric shock,
do not disassemble this product.
Take it to a qualified service
technician when service or repair
work is required. Opening or
removing covers may expose you
to dangerous voltage or other
risks. Incorrect reassembly can
cause electric shock when the
product is subsequently used.
17. Unplug this product from the wall
outlet and refer servicing to
qualified service personnel under
the following conditions:
7
• When the power cord plug is
damaged or frayed.
• If liquid has been spilled, into
the product.
• If the product has been exposed
to rain or water.
• If the product does not operate
normally by following the
operating instructions. Adjust
only those controls that are
covered by the operating
instructions because improper
adjustment of other controls
may result in damage and will
often require extensive work by
a qualified technician to restore
the product to normal operation.
• If the product has been dropped
or the cabinet has been
damaged.
• If the product exhibits a distinct
change in performance.
18. Avoid using a telephone (other
than a cordless type) during an
electrical storm. There may be a
remote risk of electric shock from
lightning.
19. Do not use the telephone to report
a gas leak if the phone is in the
vicinity of the leak.
8
BATTERY SAFETY INSTRUCTIONS!
!
CAUTION
!
1. Use only the appropriate type and
To reduce the risk of fire
or injury, read and follow
these instructions.
size battery pack specified in the
instruction manual provided for this
product.
2. Do not dispose of the battery pack
in a fire. The cell may explode.
Check with local codes for possible
special disposal instructions.
3. Do not open or mutilate the battery
pack. Released electrolytes is
corrosive and may cause damage
to the eyes or skin. It may be toxic
if swallowed.
4. Exercise care in handling the
battery pack in order not to short it
with conducting materials such as
rings, bracelets, and keys. The
battery or conductor may overheat
and cause burns.
5. Charge the battery pack provided
or identified for use with this
product only in accordance with
the instructions and limitations
specified in the instruction manual
provided for this product.
6. Observe proper polarity orientation
between the battery pack and
battery charger.
9
SAVE THESE
INSTRUCTIONS
IMPORTANT
!
!
•
Cordless phones such
as this one require AC
power to operate.
When the power is off,
you cannot make or
receive calls using your
phone. To be safe, you
should also have a
phone that does not
need AC power to
operate (not a cordless
phone), so you can still
make and receive calls
if there is an AC power
failure.
INTRODUCTION
Thank you for purchasing RadioShack
Handsfree Phone. It combines the
clarity of 900 MHz communication with
portability and convenience. The
cordless handset clips to your belt or
clothing so you can make and answer
calls away from the base. The headset
allows you to use your hands while you
talk. The phone’s Caller ID unit records
each caller’s telephone number (and
name, if available in your area) and the
date and time of the call, as provided by
your local phone company to Caller ID
service subscribers. If you subscribe to
Call Waiting with Caller ID, the phone
shows you the incoming caller
•
When AC power is lost,
the phone loses the
security access-
protection code
connection between
the base and the
handset. When power
is restored, put the
handset on the base
briefly to restore this
connection so you can
use the handset.
•
Your phone operates
on standard radio
frequencies as
information, even when you are already
talking on the phone.
!
allocated by the FCC.
It is possible for other
radio units operating
nearby on similar
INSTALLATION
frequencies to
unintentionallyintercept
your conversation or
cause interference.
This possible lack of
privacy can occur with
any cordless phone.
SELECTING A LOCATION
You can place the phone’s base on a
desk or table. Select a locations that is:
Ô
10
• near an accessible AC outlet
• near a telephone line jack
Ô NOTE Ô
If your home has
• out of the way of normal activities
specially wired alarm
equipment connected to
the telephone line, be
sure that installing the
system does not disable
your alarm equipment.
• away from electrical machinery,
electrical appliances, metal walls
or filing cabinets, wireless
intercoms, alarms, and room
monitors
If you have questions
about what will disable
alarm equipment,
contact your telephone
company or a qualified
installer.
• away from other cordless phones
The base’s location affects the hand-
set’s range. If you have a choice of
several locations, try each to see which
provides the best performance.!
Your telephone connects directly to a
modular telephone line jack. If your
telephone wiring does not have a
modular jack, you can update the wiring
yourself using jacks and adapters
(available at your local RadioShack
store), or have the telephone company
update the wiring for you. You must use
compatible modular jacks that are
compliant with Part 68 of FCC Rules
and the requirements adapted by the
ACTA. The telephone cord and
!
CAUTION
!
You must use
a Class 2
power
!
source that supplies
9V DC and delivers at
least 210 mA. Its
center tip must be set
to positive and its plug
must fit the phone's
DC IN 9V jack. The
supplied adapter
modular plug provided is Part 68
compliant for connecting to the
telephone company network.
meets these specifi-
cations.
(continued)
11
1. Plug one end of the supplied long
modular cord into the TEL LINE
jack on the bottom of the base.Ô
!CAUTION
(continued)
!
Using an adapter that
does not meet these
specifications could
damage thephone or the
adapter.
2. Plug the modular cord’s other end
into a modular phone line jack.
3. Insert the supplied AC adapter’s
barrel plug into the DC IN 9V jack
on the bottom of the base.
•
Always connect the
AC adapter to the
phone before you
connect it to AC
power. When you
finish, disconnect the
adapter from AC
power before you
disconnect it from the
phone.
4. Route the
adapter’s
cord
through
the strain
relief slot
on the
back of
the base, then plug the adapter
into a standard AC outlet.
CONNECTING/CHARGING
THE BATTERY PACK
The phone comes with a rechargeable
nickel metal hydride (Ni-MH) battery
pack in the handset, but not connected.
Before using your phone, you must
connect the battery pack, then charge it
for about 15–20 hours.
Ô NOTE Ô
The USOC number of
the jack to be installed is
RJ11C (or RJ11W for a
wall plate jack).
1. Remove the belt clip.
12
2. Press down and slide off the
battery compartment cover.
3. Lift the battery pack out of the
compartment.
4. Plug the battery pack’s connector
into the socket in the compartment
(the connector fits only one way),
then place the battery pack in the
compartment.
5. Replace the cover.
To charge the battery pack, place the
handset on the base. The CHARGE/IN
USE indicator on the base lights and
Total:00appears on the handset
display.
Recharge the battery pack when Low
Batteryflashes on the display.
If you have trouble replacing the battery
pack, take the phone to your local
RadioShack for assistance.
RECHARGING THE BATTERY
PACK
• When you first use the phone after
charging or recharging the battery
pack, the phone might not work
and you might hear an error tone
when you press TALK.
13
While holding PAGE, return the
handset to the base for about 3
seconds to reset the security
access-protection code. o !
• If the base loses power for about
an hour while the handset is away
from it, the security access
protection code might be lost.
Place the handset on the base to
reset the code.
WARNING
o
o
Dispose of the old
battery pack promptly
and properly. Do not
burn or bury it. See
“Battery Safety
Instructions” on Page 9
for additional information
on proper battery
handling.
• If the battery pack becomes weak
during a call, the handset beeps
every 3 seconds and Low Battery
flashes. When this happens, you
cannot make a call until you
recharge the battery pack.
• If the display is blank and the
phone does not work, recharge the
battery pack. (The battery power
might be too low to light the
display.)
• About once a month, fully
discharge the battery by keeping
the handset off the base until Low
Batteryflashes on the display.
Otherwise, the battery pack loses
its ability to fully recharge.
IMPORTANT
!
!
Be sure the battery pack
is properly connected
before you try to charge
it. The CHARGE/IN USE
indicator lights when the
handset is on the base,
even if the battery pack
is not connected.
• The handset loses its security
access-protection code if the
battery pack is completely
discharged. Place the handset on
14
the base to recharge the battery
pack and reset the code.
• Using a dry cloth, clean the
charging contacts on the handset
and base about once a month.
• If you are not going to use your
phone for an extended period,
disconnect the battery pack. This
increases the battery pack’s
usable life.
• The supplied battery pack should
last for about a year. If the battery
pack does not hold a charge for
more than 2 hours after an
overnight charge, replace it with a
new 3.6-volt, 600 mAh battery
pack with a connector that fits the
socket in the battery compartment.
You can order a replacement
battery pack through your local
RadioShack store. Install the new
battery pack and charge it for
about 15–20 hours.
CONNECTING AND
ADJUSTING THE HEADSET
1. Insert the headset’s plug into the
jack on the side of the handset.
15
2. Place the headset on your head
with the earpiece over either ear.
!
CAUTION
!
The microphone boom
swivels on the headset.
Do not bend the
microphone boom while
you adjust it.
3. Adjust the headset band until it
rests with almost no pressure on
your ear and the top of your head.
If the headset is loose, press in
slightly to tighten it. If it is tight,
gently pull the headset band out to
loosen it.
4. Hold the headset in place and
adjust the microphone boom until it
is about even with (but not in front
of) your mouth. Experiment until
you find the most comfortable posi-
tion.!Ô
Ô NOTE Ô
When you are not using
the headset, place it on
the headset hanger.
Otherwise (if you set it
on a flat surface, for
example), you might
have to repeat these
adjustments.
If desired, use the lapel clip on the
headset cord to attach the cord to your
clothing. Leave enough slack in the
cord so you can move your head
without pulling the headset.
16
ATTACHING THE HEADSET
HOLDER
Insert the tabs on the
headset holder into
the slots on the back
of the base and snap
the holder into place.
USING THE BELT CLIP
Use the belt clip to hang the handset on
your belt or waistband for handsfree
carrying.
SETTING THE RINGER
TONE AND VOLUME
You can select one of five different
ringer tone/volume settings on the
handset. Lift the handset and
repeatedly press "or #to select the
desired ringer setting. Each time you
press the button, the phone rings at the
selected setting and the display shows
Ring Type A High, Ring Type A Low,
Ring Type B High, Ring Type B Low, or
Ringer Off.
17
TURNING AUTO TALK
ON/OFF
Your phone is preset so you must press
TALK when you lift the handset from the
base to answer a call. With Auto Talk
turned on, you can answer a call by just
lifting the handset from the base. If the
handset is away from the base, you can
answer by pressing TALK, any number,
∗/TONE/$, or #/%.
1. Lift the handset and hold down
CID/MENU until the menu appears
with AutoTalkselected.
2. Press SELECT to change the Auto
Talk setting. Onor Offappears
indicating the selected setting.
3. Return the handset to the base (or
press END) to store the new
setting.
TURNING CALLER ID/CALL
WAITING ON/OFF
If you subscribe to Call Waiting with
Caller ID service, you can set the
phone to show Caller ID information for
an incoming call even while you are
using the phone.
18
1. Lift the handset and hold down
CID/MENU until the menu appears
with AutoTalkselected.
2. Press 2 or #to move the cursor to
CIDCW(Caller ID/Call Waiting).
3. Press SELECT to change the Caller
ID/Call Waiting setting. Onor Off
appears indicating the selected
setting.
4. Press END and return the handset
to the base to store the new
setting.
STORING YOUR AREA
CODE
Ô NOTE Ô
If an area code is
You can store your local area code in
the phone’s memory so it will not show
the area code if you receive a local call.
If you need to add or store the area
code for a local number, you can add it
afterwards (see “Adding/Deleting the
Area Code” on Page 36).Ô
already stored, it
appears on the display
after you hold down
CID/MENU. Press
DELETE/CHANNEL
three times to delete the
area code. Then enter
your area code.
1. Lift the handset and hold down
CID/MENU until the menu appears
with AutoTalkselected.
2. Press 3 or #to move the cursor to
Area Code.
19
3. Press SELECT, then enter your
three-digit area code. If you make
a mistake, repeatedly press
∗/TONE/$or #/%to move the
cursor over the incorrect digit, then
enter the correct number.
IMPORTANT
!
!
In some areas, the area
code is necessary even
for a local call. If you live
in such an area, do not
store the area code.
4. Press SELECT to store the area
code, then press END or return the
handset to the base.
!
SETTING THE DIALING
MODE
Your phone is set for tone dialing. If you
have pulse service, change the dialing
mode. If you are not sure which type of
service you have, do this test.
Ô NOTE Ô
If your phone system
requires that you dial an
access code (9, for
example) before you
dial an outside number,
do not dial the access
code either.
1. Lift the handset, press TALK, and
listen for a dial tone.
2. Press any number other than 0. Ô
If the dial tone stops, you have
touch-tone service. If the dial tone
continues, you have pulse service.
3. Press END.
Follow these steps to set the dialing
mode.
20
1. Lift the handset then hold down
CID/MENU until the menu appears
with AutoTalkselected.
2. Press 4 or#to move the cursor to
Dial, then press SELECT to
change the dialing mode setting.
Toneor Pulseappears, indicating
the selected setting.
3. Return the handset to the base (or
press END) to store the new
setting.
SELECTING THE LANGUAGE
You can select the language on the
display, either English or French.
1. Lift the handset and hold down
CID/MENU until the menu appears
with AutoTalkselected.
2. Press 5 or#to move the cursor to
Language.
3. Press SELECT to select Eng
(English) or Fr. (French).
4. Return the handset to the base or
press END to store the new setting.
21
OPERATION
The handset window has plastic film on
it to protect it during shipment. Carefully
peel off the film before using your
phone.
MAKING AND RECEIVING
CALLS
To make a call, lift the handset and
press TALK. Talkand the current
volume setting appear on the handset’s
display, and the CHARGE/IN USE
indicator on the base lights. Dial the
number. The number appears on the
handset as you dial, then the call’s
elapsed time appears. To end a call,
place the handset on the base or press
END.
You can also dial the number before
you press TALK. If you make a mistake,
press DELETE/CHANNEL until the
incorrect entry is erased, then enter the
correct number. To delete the entire
number, hold down DELETE/CHANNEL.
When you receive a call, IncomingCall
appears. To answer the call, lift the
handset and press TALK. If Auto Talk is
on, just lift the handset. If the handset is
away from the base, press TALK, any
22
number, ∗/TONE/$
, or #/%
. T
a
l
k
appears on the handset’s display. To
end a call, place the handset on the
base or press END.
SELECTING THE CHANNEL
The phone has 20 channels. If the call
disconnects or you experience difficulty
hearing the conversation, press
DELETE/CHANNEL on the handset to
select a different channel during a call.
Scanningappears as your phone
searches for a clear channel.
ADJUSTING THE HEADSET’S
VOLUME
To adjust the volume of the sound you
hear through the handset during a call,
press "or #on the handset until you
obtain the desired volume level. Volume
Maximum, VolumeHigh, VolumeMedium, or
VolumeLowappears on the handset
display. Once you set the volume level,
the setting is maintained even after you
hang up the phone. Ô
Ô NOTE Ô
When you press "
while the volume is
maximum or #while
the volume is low, the
setting does not change.
The phone sounds three
short beeps.
USING REDIAL
You can quickly dial the last number
you dialed. Lift the handset and press
23
REDIAL/PAUSE, then TALK. The phone
dials the number. Ô
Ô NOTE Ô
•
•
You can also press
REDIAL/PAUSE
after pressing TALK.
USING FLASH
TALK performs the electronic
The redial memory
holds up to 32 digits,
so you can redial
long-distance as well
as local numbers.
equivalent of a switchhook operation
for special services, such as Call
Waiting. For example, if you have Call
Waiting, press TALK to answer an
incoming call without disconnecting the
current call. Press TALK again to return
to the first call.
•
The redial memory
also holds pause
entries (see
“Entering a Pause”
on Page 28).
If you do not have any special phone
services, pressing TALK might
disconnect the current call.
MUTING THE RINGER
To temporarily mute the ringer’s tone
when you receive a call with the
handset off the base, press END.
Ringer mute automatically turns off
when you receive another call.
USING TONE SERVICES ON
A PULSE LINE
Some special services require tone
signals (such as bank-by-phone). If you
have pulse dialing, you can still use
these special tone services.
24
Dial the service’s main number. When
the service answers, press ∗/TONE/$.
Any additional numbers you dial are
sent as tone signals. The phone’s dial
mode resets to pulse when you make
or receive a call.
PAGING
To send a page from the base to the
handset or to locate the handset when
the phone is not in use, press PAGE on
the base. The handset beeps for about
1 minute. Pagingappears on the
handset while the page sounds.
To stop the page, press any key on the
handset, place the handset on the
base, or press PAGE on the base again.
The phone rings when a call comes in
while you are using the page feature.
MEMORY DIALING
You can store up to 10 phone numbers
and names in memory, then dial a
stored number by entering its memory
location number. Each number can be
up to 20 digits, and each name can be
up to 14 characters.
25
STORING A NUMBER AND
NAME IN MEMORY
1. Lift the handset.
2. Hold down MEMORY until Memory
Storeand a list of memory location
numbers appears.
3. Select an empty memory location
(or the one you want to replace) by
entering the location number (1–0)
or using "or #to scroll through
the list.
4. Press SELECT. StoreName
appears. If you do not want to
enter a name, skip to Step 6.
5. To enter a name, use the number
keys.
Refer to the letters on the number
keys to select the desired letter.
Press the key once for the first
letter in the upper case, press
twice for second letter in the upper
case, and so on. To enter the lower
case letter, press four times (or five
times) to display the first letter in
lower case, five or six times for
second letter, and so on.
For example, to enter John: press
5 once; upper case Jappears.
26
Then press 6 six times; lower case
oappears. Press 4 five times;
lower case happears. Finally,
press 6 five times; lower case n
appears.
To enter two letters from the same
key in a row, press #/%to move
the cursor to the next position. For
example to enter AB, press 2 once;
Aappears. Then press #/%, the
cursor moves to next position, then
press 2 twice so Bappears.
To enter a space, press #/%twice
without entering any character.
To enter a number, repeatedly
press the corresponding number
key until the number appears.
To enter a special character, press
0. Each time you press 0, the
following characters appear in this
order:
∗ # –& ( )(space) 0
If you make a mistake, use
∗/TONE/$or #/%to move the
cursor over the error, and press
DELETE/CHANNEL to delete a
character, then enter the correct
character. To delete all characters,
27
hold down DELETE/CHANNEL for at
least 1 second.
6. Press SELECT. StoreNumber
appears.
Ô NOTE Ô
Each tone or pause
entry uses one digit of
memory.
7. Enter the number and any tone
and pause entries (see “Using
Tone Services on a Pulse Line” on
Page 24 and “Entering a Pause”
on Page 28). Ô
8. Press SELECT. The phone beeps
and MemorynStoredappears (n=
number). After a few seconds,
MemoryStoreappears, and you can
repeat Steps 3–8 to store more
numbers.
To replace a stored number, simply
store a new one in its place.
ENTERING A PAUSE
In some telephone systems, you must
dial an access code (9, for example)
and wait for a second dial tone before
you can dial an outside number. You
can store the access code with the
phone number; however, you should
also store a pause after the access
code to allow the outside line time to
connect.
28
To enter a 2-second pause, press
REDIAL/PAUSE. Adding more pause
entries results in a longer pause.
EDITING OR DELETING A
NUMBER IN MEMORY
1. Lift the handset.
2. Hold down MEMORY until Memory
Storeand a list of memory location
numbers appear on the handset
display.
3. Choose a memory location (1–0)
by pressing a number or by
repeatedly pressing "or #.
4. Press SELECT. Three options (Edit
Memoryn, DeleteMemorynand Go
Back) appear. Press "or #to
choose the option, then press
SELECT to choose it.
EditMemoryn— edit the record as
described in Steps 5 through 8 of
“Storing a Number and Name in
Memory” on Page 26.
DeleteMemoryn — the display
prompts you to confirm the
deletion. Press "to move the
cursor to Yes, then press SELECT
or DELETE/CHANNEL. The phone
29
beeps, and M
e
m
or
y
n
D
el
e
te
d
appears.
GoBack— returns you to the list of
memory numbers.
REVIEWING MEMORY NUMBERS
To review your memory numbers,
press MEMORY. The list of memory
location numbers (1–0) appears with
the name stored with each number (or
<Memoryn>if you did not store a name).
Ô NOTE Ô
To see the stored phone numbers,
press #/%. Only the first 13 characters/
numbers appear for number. To see
the rest of the number, press #/%
when the number is on the display.
Press ∗/TONE/$to return to the name
display.
To view the name and
number at the same
time, press SELECT
when the cursor is by a
memory location
number. To exit this
display, hold down
DELETE/CHANNEL
until the display clears,
or press END.
To exit the memory number list, press
END. Ô
DIALING A MEMORY NUMBER
To dial a number stored in memory, lift
the handset and press MEMORY. The
list of memory location numbers
appears. Choose a memory location
(1–0) by pressing a number or by
repeatedly pressing "or #, then
press TALK.
30
You can also dial a memory number
after pressing TALK. Press MEMORY
(the display does not change but the
phone’s memory recall activates), then
press the desired memory location
number.
CHAIN-DIALING SERVICE
NUMBERS
For quick recall of numbers for special
services (such as bank-by-phone),
store each group of numbers in its own
memory location.
Dial the service’s main number first.
Then, at the appropriate place in the
call, press MEMORY and enter the
number for the location where the
additional information is stored.
TESTING STORED EMERGENCY
NUMBERS
If you store an emergency service’s
number (police department, fire
department, ambulance) and you
choose to test the stored number, make
the test call during the late evening or
early morning hours to avoid peak
demand periods. Also, remain on the
line to explain the reason for your call.
31
SPEED DIALING
Ô NOTE Ô
The memory location
used by the phone to
store a speed dial
number is separate from
the ones used to store a
name and number.
You can store one number you dial
often in the phone’s speed dial
memory. Speed dial lets you dial a
number by pressing a single button. Ô
STORING A NUMBER IN SPEED
DIAL
1. Lift the handset.
2. Hold down SPEED DIAL until Store
Numberappears.
3. Follow the steps under “Storing a
Number and Name in Memory” on
Page 26 to store a number.
4. Press SELECT. The phone beeps
and Number Storedappears.
DIALING THE SPEED DIAL
NUMBER
Simply press SPEED DIAL to dial the
stored speed dial number. You do not
have to press TALK.
EDITING THE SPEED DIAL
NUMBER
1. Lift the handset.
2. Hold down SPEED DIAL until the
speed dial menu appears.
32
3. When the cursor is at E
d
i
t
N
um
b
e
r,
press SELECT.
4. To edit the number, repeatedly
press DELETE/CHANNEL to erase
up to the incorrect entry, enter the
correct number, then press
SELECT.
DELETING THE SPEED DIAL
NUMBER
1. Lift the handset.
2. Hold down SPEED DIAL until the
speed dial menu appears.
3. Press # to choose Delete
Number, then press SELECT.
4. Press " to move the cursor to
Yes, then press SELECT or
DELETE/CHANNEL. The phone
beeps once and Number Deleted
appears.
CALLER ID
OPERATION
If you subscribe to Caller ID service
from your phone company, the phone
company sends information about the
call, as well as the time and date,
between the first and second rings of
33
every call you receive. The phone
displays this information after the
second ring, and it stores up to 30
Caller ID records for later review. It also
shows if the caller information is
unavailable or if the name and number
were blocked by the caller (see “Caller
ID Messages” on Page 35).
If you subscribe to Call Waiting with
Caller ID, you hear a tone through the
handset when a call comes in, then the
Caller ID record appears. If the Caller
ID memory becomes full, any new call
replaces the oldest call’s record.
IMPORTANT CALLER ID
INFORMATION
To use the phone’s Caller ID and Caller
ID with Call Waiting features, you must
be in an area where those services are
available and you must subscribe to
those services through your local
phone company.
Where Caller ID is offered, one or more
options are generally available:
• caller’s number only
• caller’s name only
• caller’s name and number
34
REVIEWING CALLER ID
RECORDS
To review the Caller ID records, lift the
handset and press CID/MENU. The
number of new Caller ID records, if any,
and the total number of records
appears. Repeatedly press #to scroll
through the Caller ID records from the
newest to the oldest, or "to scroll
back through the records. To scroll
quickly through the records, hold down
"or #.
The top line of each record shows the
date, time and the number of calls from
that number. The second line shows
the caller’s name (if available), and the
third line shows the caller’s phone
number.
CALLER ID MESSAGES
Display
New: XX
Total: XX
Description
Shows the number of
new Caller ID records
(records you have not
reviewed) and the total
number of records.
PrivateName or The caller has blocked
PrivateNumber the caller ID informa-
tion.
35
Display
Description
UnknownName or The caller is not within
UnknownNumber a Caller ID service
area.
IncompleteData Appears if there was
an error during the
transmission of Caller
ID information. Occa-
sional errors are nor-
mal. If the phone
frequently displays
Incomplete Data,
contact your local tele-
phone company or
your local RadioShack
store.
ADDING/DELETING THE
AREA CODE
The display shows the area code of an
incoming call, unless the call comes
from the area code you stored (see
“Storing Your Area Code” on Page 19).
You can add the area code to the
display or delete it. With the record
displayed, press 3 to add or delete the
area code.
Numbers are stored in memory as they
appear on the display, with or without
the area code. Numbers in Caller ID
36
records remain the same, even if you
add or delete the area code.
DIALING NUMBERS FROM
A CALLER ID RECORD
To dial a local number stored in a Caller
ID record, recall the record, then press
TALK.
Ô NOTE Ô
If a Caller ID record
does not contain a
To add or delete the area code, press 3
before you press TALK.
phone number (if it was
blocked by the caller, for
example), you cannot
dial from that record.
If the call is long distance, press 1
(1appears before the displayed
number) before you press TALK. Ô
STORING A CALLER ID
RECORD IN MEMORY
Follow these steps to store the name
and number from a Caller ID record into
a memory location.
1. Press CID/MENU then #to recall
the record you want to store. To
add or delete the area code, press
3. If it is a long distance number,
press 1.
2. Press MEMORY. SelectLocation
appears.
37
3. Choose a memory location (1–0)
by pressing a number or by
repeatedly pressing "or #, then
press SELECT.
If the selected location is empty,
the phone beeps to confirm that it
stored the number, then the Caller
ID record appears.
If a record exists in the selected
location, ReplaceMemory?appears,
prompting you to confirm the
replacement. Press "or #to
move the cursor to Yesor No, then
press SELECT.
DELETING CALLER ID
RECORDS
You can delete Caller ID records indi-
vidually or all at once.
DELETING A SINGLE CALLER ID
RECORD
1. Press CID/MENU then #to recall
the record you want to delete.
2. Press DELETE/CHANNEL. Delete
Message?appears, prompting you
to confirm the deletion.
3. When the cursor is at Yes, press
SELECT or DELETE/CHANNEL. The
38
phone beeps once, indicating that
the record was deleted.
DELETING ALL CALLER ID
RECORDS
1. Press CID/MENU so the record
totals appear.
2. Press DELETE/CHANNEL. Delete
All?appears, prompting you to
confirm the deletion.
3. Press "to move the cursor to
Yes, then press SELECT or
DELETE/CHANNEL. The phone
beeps once and TOTAL:00appears,
indicating that all Caller ID records
were deleted.
39
TROUBLESHOOTING
We do not expect you to have any
problems with your phone, but if you
do, these suggestions might help.
Problem
Suggestions
Be sure the base’s phone
line cord and AC adapter
are correctly and securely
connected.
The phone
does not work
properly.
Be sure the battery pack
in the handset is
connected and charged.
Return the handset to the
base for about 3 seconds
to reset the security
access-protection code.
The display
Be sure the battery pack
flashes slowly in the handset is
when the
handset is
faceup on the
base.
connected and charged.
The handset
Move the handset closer
stops working to the base.
or works poorly
Be sure the handset’s
during a call.
battery pack is charged.
(If the battery pack power
is too low, the handset
cannot display Low
Battery.)
40
Problem
Suggestions
Low volume or Make sure the headset’s
unusual
sounds.
plug is properly con-
nected to the jack.
Someone has picked up
another phone on the
same line. Hang up the
other phone.
Your conversa- Keep the handset away
tion is difficult from computers, remote
to hear due to control toys, wireless
dropout or mut- microphones, alarm sys-
ing.
tems, intercoms, room
monitors, fluorescent
lights, and electrical
appliances.
Move to another location
or turn off the source of
interference.
Press DELETE/CHAN-
NEL to change the chan-
nel.
Hang up and redial the
number.
The phone
Return the handset to the
base and recharge the
battery pack.
cannot be
operated at a
useful dis-
tance from the
base because
the signal
becomes weak
or noisy (hand-
set’s range has
decreased).
Be sure the base’s
antenna is not touching a
metal surface.
41
Problem
Suggestions
The handset
battery pack
does not
Check the charging con-
tacts on the handset and
base. If they are dirty,
clean them with a dry
cloth.
charge.
Be sure the battery pack
is connected correctly.
Be sure the handset is
properly seated on the
base.
Replace the battery pack.
The handset
does not ring
or receive a
page.
Move the handset closer
to the base.
Be sure the battery pack
in the handset is con-
nected and charged.
Move the base away from
other electrical devices.
You have an
incoming call,
but do not
receive any
Caller ID
Let the phone ring twice
before you answer so the
system has time to record
the Caller ID information.
Check that the system is
correctly and securely
connected.
information.
Check with your phone
company to verify that
your Caller ID service is
active.
42
If you still have problems, disconnect
the phone. If other phones on the same
line work properly, the fault is in this
phone or its installation. If you cannot
find the problem, take the phone to
your local RadioShack store for
assistance.
CARE
Keep the phone dry; if it gets wet, wipe
it dry immediately. Use and store the
phone only in normal temperature
environments. Handle the phone
carefully; do not drop it. Keep the
phone away from dust and dirt, and
wipe it with a damp cloth occasionally
to keep it looking new.
SERVICE AND
REPAIR
If your phone is not performing as it
should, take it to your local RadioShack
store for assistance. Modifying or
tampering with the phone’s internal
components can cause a malfunction
and might invalidate its warranty and
void your FCC authorization to operate
it.
43
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing de-
fects in material and workmanship under normal use for one (1) year
from the date of purchase from RadioShack company-owned stores
and authorized RadioShack franchisees and dealers. EXCEPT AS
PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WAR-
RANTIES AND ANY IMPLIED WARRANTIES, INCLUDING THOSE
OF MERCHANTABILITY AND FITNESS FOR
A
PARTICULAR
PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF
THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN.
EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO
LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY
OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABIL-
ITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY
USE OR PERFORMANCE OF THE PRODUCT OR ARISING OUT
OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT
LIMITED TO, ANY DAMAGES RESULTING FROM INCONVE-
NIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR
PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSE-
QUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN AD-
VISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied war-
ranty lasts or the exclusion or limitation of incidental or consequen-
tial damages, so the above limitations or exclusions may not apply
to you.
In the event of a product defect during the warranty period, take the
product and the RadioShack sales receipt as proof of purchase date
to any RadioShack store. RadioShack will, at its option, unless oth-
erwise provided by law: (a) correct the defect by product repair with-
out charge for parts and labor; (b) replace the product with one of
the same or similar design; or (c) refund the purchase price. All re-
placed parts and products, and products on which a refund is made,
become the property of RadioShack. New or reconditioned parts
and products may be used in the performance of warranty service.
Repaired or replaced parts and products are warranted for the re-
mainder of the original warranty period. You will be charged for re-
pair or replacement of the product made after the expiration of the
warranty period.
This warranty does not cover: (a) damage or failure caused by or at-
tributable to acts of God, abuse, accident, misuse, improper or ab-
normal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess volt-
age or current; (b) any repairs other than those provided by a Ra-
dioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping
or insurance costs; or (f) costs of product removal, installation, set-
up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor,
Fort Worth, TX 76102
12/99
43-3906
UCZZ01387BA
03A03
RadioShack Corporation
Fort Worth, Texas 76102
Printed in China
|