Built-under Freezer
User Guide
&
Installation & Service Instructions
Please keeP for fUtUre reference
U110120 - 01A
1. Before You Start
Thank you for buying a Rangemaster appliance. We hope
that it provides a stylish yet practical solution to your cooling
needs. We hope that this handbook supplies you with all the
information you require. If there is anything you are not sure
of please contact us (see Warranty section for the Customer
Service details).
•
•
When replacing old appliances, make sure that you
have disabled any locking mechanisms before disposal:
it may even be best to remove the appliance door
completely to prevent children from becoming trapped
inside the appliance.
The appliance must be connected to the power supply
safely. Loose connections, broken plugs and bare
wires are a safety hazard. Make sure that all electrical
connections are sound.
WarnInG: this appliance must be earthed.
Please leave the appliance to stand for at least eight
hours. this will allow the cooling system to settle
•
•
•
•
Before undertaking any routine maintenance or minor
repairs, disconnect the appliance from the electrical
supply: this includes cleaning.
following transportation.
always make sure a qualified person installs this
appliance.
DO NOT touch cold surfaces of the appliance while it is
in use as this will cause hands to stick to them leading
to freezer burns.
the freezer compartment is rated at 4 stars.
this appliance is designed for domestic use only.
Using it for any other purpose could invalidate any
When moving the appliance take care not to damage
the leads, pipes or condenser unit. Should these parts
become damaged, contact a qualified service engineer.
warranty or liability claim.
•
•
Before you plug the appliance into the mains, clean
the inside of the appliance using warm water and
bicarbonate of soda, then dry thoroughly.
Effervescent liquids (fizzy drinks) should never be
frozen. These liquids expand during freezing and
this may lead to the bottles/containers shattering or
exploding.
Check that no parts of the appliance are damaged,
especially parts of the cooling system, pipes or leads. If
damage has occurred DO NOT install the appliance. You
should contact a qualified service engineer or return the
appliance to its place of purchase.
•
•
Foods that are intended to be defrosted or cooked first,
such as breads or meats, must not be eaten in their
frozen state.
Never use sharp, metal implements to scrape ice off the
surface of this appliance. Only use implements, which
are fit for this purpose (such as plastic scrapers) and use
carefully to avoid damaging the lining of the appliance.
•
•
If the accessories inside the appliance have been
disturbed during transit, reposition them in accordance
with the instructions.
Make sure that the electrical supply to your plug socket
is correct for this appliance: the required information is
on the data badge of the appliance.
•
The cooling system contains refrigerant and oils, all of
which are harmful to health if leaked. Should leakage
occur, disconnect the appliance and ventilate the room
it is installed in. Take care to make sure that you do not
get any coolant near to, or in, your eyes.
Contact a service engineer or arrange to have the
appliance removed.
•
•
•
Once the appliance is installed, cleaned and dry, it is
ready to be plugged in and switched on.
Never allow the back coils of the appliance to come into
contact with the wall surface.
DO NOT use the appliance under any circumstances.
Never block the ventilation openings of the appliance.
It is vital to keep your appliance well ventilated, so that
there is proper airflow between the bottom of the unit
and the plinth/kickplate which it is sitting on.
Electrical safety
•
Connections to the mains supply should be in
accordance with local regulations.
•
•
The appliance must be plugged into an earthed socket.
Safety
The plug MUST be accessible after the appliance has
been positioned.
the data badge is located inside the appliance (left-
front edge of the freezer compartment).
•
The appliance is supplied with a standard three-pin
plug, of which the one for grounding should never be
removed.
WarnInG: keep this appliance clear of any
obstruction.
Do not damage the refrigerant circuit. If it does
become damaged, do not use the appliance. In case
of damage, contact customer service, ventilate
the room where the appliance is located and avoid
flames.
•
•
Hold the plug, not the electrical cable, when
unplugging the appliance.
Make sure that the appliance does not trap the electric
cable.
•
•
Do not step on the cable.
WarnInG: Do not use mechanical devices (such as
hair dryers) to defrost this appliance.
Avoid damage to the electric cable when moving the
appliance.
1
Damaged electrical cable
If the electrical cable is damaged or worn, turn off the
appliance and consult an authorised agent for replacement.
Caring for the Environment
Disposing of your packaging
Your new freezer was protected by suitable packaging
while on its way to you. All of the materials used are
environmentally friendly for disposal and can be recycled.
Please make a contribution to protecting the environment by
disposing of the packaging appropriately.
Refrigerant Gas Information
IMPortant: This appliance is provided with refrigerant
gas, ISOBUTHANE (R600a). When moving the appliance
take care to ensure that it is not excessively struck or
shaken. Failure to do so could damage the appliance.
Disposing of your old freezer
Damage to the refrigerating circuit, with possible leaking of
refrigerating gas, could create a risk of explosion caused by
external sparks or flames.
This symbol on the product or its packaging
indicates that the product may not be treated as
household waste. Instead it should be handed
ArtNo.000-019
over your local community waste collection/
recycling centre.
Do not bin logo
In the event of accidental leakage
Allow the material to evaporate if there is adequate
ventilation.
Old appliances still have some residual value. An
environmentally friendly method of disposal will make sure
that valuable raw materials can be recovered and used again.
Behaviour of the gas
When an appliance has reached the end of its working life
unplug it from the mains. Cut off the mains cable and dispose
of it together with the plug.
This refrigerant gas is highly flammable so do not allow the
gas to come into contact with hot surfaces or naked flames.
Gas R600a is heavier than air: if released it forms a high
concentration at floor level where ventilation is poor.
Make the door unfit for use (by removing the seals) or remove
the door so that children cannot accidentally lock themselves
in.
First aid
Inhalation
Cycloisopenthane, a flammable substance not harmful to
ozone, is used as an expander for the insulating foam.
Take the exposed person from the polluted area and carry
them to a warm, well ventilated place.
When transporting the appliance, take care not to damage
the cooling circuit.
Long exposure can cause the onset of asphyxia and
possible loss of consciousness. If necessary, practice artificial
respiration, and in the most serious cases, administer oxygen
under close medical supervision.
By making sure this product is disposed of correctly, you
will help prevent potential negative consequences for the
environment and human health, which could otherwise be
caused.
Skin contact
It is unlikely that occasional contact with the skin is
dangerous. If this should happen, thoroughly wash the
affected zone.
For more detailed information about recycling of this
product, please contact your local council, your household
waste disposal service or the shop where you purchased the
product.
Liquid splashes and atomised liquid can cause freezing burns.
Wash the affected part with plenty of water and call a doctor
to treat any burns.
Eye contact
Wash with plenty of water, with eyelids well open, and call a
specialist doctor as soon as possible.
In any event, should you inhale or come into contact with
r600a gas, we advise you to consult your own doctor.
2
2. About Your Freezer
fig.2-1
Control panel
1
2
3
0
4
Freezer drawers
Ventilation grills
Levelling feet
The freezer is shown in fig.2-1 and has the following features: Ice creams and water ices are best stored towards the rear of
the appliance where it is coldest.
•
•
•
•
•
•
•
•
•
Manual defrost
Large/heavier portions of food, such as meats joints for
roasting are best stored in the drawer at the bottom of the
appliance, while less weighty items should be stored in the
upper drawers: this is to prevent damage to the appliance.
Adjustable thermostat
LED controls
Temperature rise warning indicator
Fast freeze function
3 wire drawers
Always make sure that food stored is suitable for freezing, and
that you have stored it securely inside the appliance.
Reversible door
Defrosting Food for Cooking
Should food become partially thawed, or defrosted it should
be consumed as soon as possible as the quality will be
affected by defrosting.
Door-on-door fittings
Adjustable feet
About the Freezer Compartment
The freezer compartment consists of 3 wire drawers and an
ice tray.
always make sure that food is thoroughly defrosted
before cooking and no ice crystals remain. this
is especially important for poultry, as this can be
extremely harmful to health.
The freezer compartment temperature must have already
reached –18 °C (or lower) before you attempt to store food
that is already frozen or freezing fresh food.
Always follow the defrosting instructions on packaging when
defrosting ready meals. Manufacturers’guidelines are always
best, as some frozen foods should be cooked from frozen.
Certain areas of the freezer are better for storage of certain
foods.
3
Freezer Controls
The freezer control panel is at the top of the freezer (fig.2-2).
fig.2-2
B
C
D
A. Fast freeze switch.
1
2
3
B. Fast freeze light (Orange): this will light up when the fast
0
freeze switch has been activated.
C. Temperature rise warning light (Red): this will light up
when the appliance detects a rise in temperature that
could affect the contents of your freezer.
4
D. Power light (Green): this will light up as soon as the
A
E
appliance is connected to the mains supply.
Setting the thermostat
The thermostat control knob is located on the control panel
at the top of the freezer (fig.2-3).
A – Fast Freeze switch, B – Fast freeze light,
C – Temperature rise warning light, D – Power light neon,
E – Thermostat dial
The thermostat automatically regulates the temperature
inside of the freezer, depending on what number you have
turned the thermostat control knob to:
fig.2-3
1
2
3
•
•
•
•
•
Position [0] means that the freezer will not cool.
However, the power light will still function.
0
Position [1] will give you a higher temperature inside of
the freezer.
Position [4] will give you a lower temperature inside of
the freezer.
4
Ideally the thermostat should be set to a position of
between [2] to [3].
The freezer can cool to –18 °C and lower.
IMPortant: The ambient temperature of the room, the
temperature of the food and the amount of food that has
been placed in the appliance and how often the door is
opened, will all affect the temperature being maintained by
the appliance.
on the maximum setting (position [4]), the freezer will
work harder to maintain a lower temperature. there is no
need to run the appliance on this setting for long periods
and you should return the thermostat knob to between
[2] and [3].
During First Use
Switch on the appliance for the first time, and set the
thermostat dial to maximum for 24 hours.
When you first switch on the appliance, the compressor will
run continuously for approximately 24 hours or until the
freezer reaches a cool enough temperature.
note: During this time, try not to open the door frequently or
place a large amount of food within the appliance.
You should then adjust the thermostat dial down to its
normal operating position.
If the unit is switched off or unplugged, allow at least 5
minutes before restarting the appliance on the thermostat or
connecting it to your mains supply.
4
Freezing Fresh Food
To freeze the maximum quantity of fresh food specified
above, turn the thermostat knob to position [4] 24 hours
before attempting freezing (fig.2-4).
fig.2-4
1
2
3
0
For smaller quantities of fresh food, turn the thermostat knob
to position [4] approximately 6 hours before attempting
freezing.
Alternatively, you can use the Fast Freeze option (see the
‘Freezing with fast freeze’ section).
4
Fresh food should be packed into airtight containers or
packaging. This will help to make sure that the food does not
dry out or lose its flavour. It will also make sure that flavour
does not transfer from other foods.
1
2
3
fig.2-5
0
4
DO NOT allow fresh food to touch items that are already
frozen.
After 24 hours check that the fresh food is satisfactorily
frozen. If it is, then turn down the thermostat to its normal
setting (between [2] and [3]).
Freezing with Fast Freeze
Press the Fast Freeze switch (fig.2-5) and the freezer will start
to run continuously at its maximum setting. The orange Fast
Freeze light will come on.
There is no need to adjust the thermostat knob.
The freezer temperature will decrease and the appliance will
get to its lowest temperature.
Place the food that is to be frozen inside the freezer.
Once the food is frozen, switch off the fast freeze setting.
Do not switch off the fast freeze setting until the
food is fully frozen.
The orange fast freeze light will go out and your appliance
will return to normal operation.
Do not leave the appliance running in fast freeze
mode for longer than 24-hours at a time.
5
3. Food Storage Tips
Tips on Freezing Food
•
•
When storing commercially frozen foods, please follow
these guidelines:
•
As with storing fresh foods, suitable packaging, correct
temperature and food hygiene will enhance the quality
of the food you are freezing.
Always follow manufacturers’guidelines for the length
of time you should store food for. Do not exceed these
guidelines!
•
•
•
Avoid putting hot foods into the freezer. First let them
cool until they reach room temperature.
•
•
•
Try to keep the length of time between purchase and
storage as short as possible to preserve food quality.
Make sure that all foods for freezing are of a high
quality, and suitable for freezing.
Buy frozen foods, which have been stored at a
temperature of –18 °C or below.
Use packaging material that is odourless and airproof
(such as plastic bags) to store food in so different foods
can be mixed without affecting the quality. Make sure
that it is airtight. Leaking packaging will dehydrate the
products and lead to loss of beneficial vitamins.
Avoid buying food which has ice or frost on the
packaging. This indicates that the products might have
been partially defrosted and refrozen at some point:
temperature rises affect the quality of food.
•
•
•
Keep the surface of the packaging dry: this keeps the
packs from freezing together.
•
Should there be a power cut or the freezer fails for any
length of time, you may need to remove food from the
freezer and store in a cold, hygienic place (i.e. garage
or outhouse area) until the power is restored or the
appliance is repaired.
Mark packages with the kind of food contained and the
date of storage.
Food needs to be frozen quickly, so it is best to freeze
small portions whenever possible and to make sure
that they are as cold as possible before storage. The
recommended maximum weight for each portion is
2.5 kg.
To prevent undue temperature rises, you should wrap
the foods in layers of insulating material, such as
newspaper, to help to maintain their temperature. It is
also important that any food affected by this situation
should be either consumed or cooked and refrozen
(where suitable) soon afterwards in order to prevent
health risks.
•
Keep food which is fresh away from food which is
already frozen, if you need to freeze fresh food every
day, make sure that it is in small portions to prevent this.
•
•
Do not exceed the maximum load for freezing, which is
given as 9 kg / 24-hours (see data badge for details).
Layers of newspaper can also be used to help keep
foods cold while you are defrosting the freezer (see
‘Cleaning and Maintenance’).
Write the expiry date and food names on the outside of
the packaging so you can be assured of the food type
and when it is safe to eat.
•
•
Take food from the freezer to defrost when needed.
Defrosted food cannot be refrozen unless it is cooked.
Do not put too much fresh food into the freezer at once.
This could go beyond the freezer’s cooling capacity (see
‘Technical Data’).
6
4. Installation
Positioning Your Appliance
IMPortant: We recommend that two people install this
fig.4-1
appliance.
600
Choosing the Right Location
The appliance should be installed in a location where
the ambient temperature corresponds with the climate
classification as stated on the rating plate.
Your appliance may not function correctly if the ambient
temperature falls outside of the following ranges.
climate
classification
appropriate ambient
820-870
temperature
SN
N
+10 to +32°C
+16 to +32°C
600 max
Avoid exposing the appliance to direct sunlight and sources
of heat (such as radiators, heaters or cookers).
ArtNo 600-0053 - BILF - cabinet dimensi
Make sure the appliance is installed with the correct
ventilation requirements. Restricting ventilation can increase
the energy consumption by 15%.
All dimensions in mm.
The door should be able to open completely and freely.
Locate the appliance so you can easily access the food that is
stored in it.
Make sure there is an electrical socket available which will be
accessible after your appliance is installed.
fig.4-1 shows the minimum opening requirements.
If this appliance is situated in a cold environment (such as
a shed, outhouse or garage) it will affect its performance.
You may find that the performance of the appliance is
not consistent and this may damage foods. a consistent
ambient temperature of 10 °c or above is recommended.
Reversing the Door
As supplied, the appliance door opens from the left. The door
can be reversed so that it opens from the right.
this procedure MUst be completed before the
furniture door is attached.
When reversing the door, keep any parts that you remove
from the appliance for later use.
take care when opening the hinges, they are sprung
loaded and there is the risk of injury if they close on
your hand.
Tools required:
•
•
Phillips screwdriver
Flat bladed screwdriver
7
Procedure
Cabinet hinge screws
fig.4-2
1. Loosen the cabinet hinge screws and carefully slide
the door off (fig.4-2). To stop the door from being
damaged, place it on a cushioned surface.
2. Lever off the cover caps on the left-hand side of the
appliance cabinet (fig.4-3).
3. Remove the door hinge screws and refit to the left-
hand side of the cabinet. These screws should only be
partially tightened.
4. Undo the door hinge screws and remove the hinges.
5. Reverse the position of the top and bottom hinges
and fit them to the left-hand side of the door (fig.4-4).
Secure in place using the door hinge screws.
6. Slide the door onto cabinet hinge screws. Tighten the
fig.4-3
screws to secure.
7. Insert the cover caps into the holes on the right-hand
side of the cabinet.
IMPortant: After you have completed reversing the door,
check that the door opens and shuts correctly without
fouling.
You should also check the door seal of the appliance. The seal
should not be creased or crushed; otherwise there will be a
gap between it and the inside of the door.
Cover caps
The seal must adhere properly all the way around the door.
If the seal is not adhering to the cabinet properly, then you
should either:
A. Use a warm damp cloth and manipulate the seal until it
does adhere to the cabinet properly, all the way around
the door, or
fig.4-4
B. Use a hair dryer on its lowest heat setting and lightly
heat the areas of the door seal that are not adhering
correctly. The heat will make the seal more pliable
and this will allow you to manipulate the seal into the
correct position.
IMPortant: DO NOT heat the door seal on anything but
the lowest heat setting or heat the seal for a long period
of time, otherwise you may damage the door seal, which
would NOT be repaired under the guarantee free of charge.
The appliance must be stood on a level floor. You can use the
levelling feet to take into account any minor unevenness in
the floor.
8
Adjusting the Feet
Make sure that the appliance is on solid level flooring. If the
refrigerator is placed on a plinth, flat, strong and fire resistant
materials must be used.
fig.4-5
This fridge has front adjustable feet, which can be used to
level the appliance.
To accesss the levelling feet, first undo the screws on each
side of the grid (fig.4-5). Remove the grid.
Using a suitable spanner, adjust the feet. Turn the spanner
clockwise to raise the feet and counter-clockwise to lower the
feet (fig.4-6).
The appliance should be flush with the underside of the
worktop and be level.
IMPortant: If the appliance is not level, then the door and
door seal may be affected.
fig.4-6
Refit the grid and secure in place.
Fitting the Plinth
You may decide to attach a plinth to match your existing
kitchen units.
-0059 - BILF - Adjusting the fe
Cut clearance in the plinth for ventilation (fig.4-7) and then
fit.
fig.4-7
90 - 140 mm
600
9
Fitting the Furniture Door
If you need the door to open from the other side, then reverse
the door before fitting the furniture door (see ‘Reversing the
door’).
fig.4-8
5 mm
=
=
Worktop
Tools required:
5 mm
•
•
•
•
Tape measure
15 mm
Sharp pencil
Small flat bladed screwdriver
Spanner
Procedure
1. Undo the 2 screws from the mounting bracket. Remove
Side view
the bracket.
2. Measure the width of the furniture door. At the halfway
point mark a line vertically down the inner surface of
the furniture door. You should draw the line from the
top of the furniture door to approximately halfway
down.
fig.4-9
Furniture door
3. Place the mounting bracket on the reverse of the
furniture door (fig.4-8). The middle of the mounting
bracket should be positioned on the line that you have
just drawn.
Mounting bracket
Adjusting
nuts
Please note the position of the mounting bracket in
the drawing – make sure that you have the mounting
bracket the correct way up.
9 mm
The top of the mounting bracket should be positioned
approximately 15mm from the top of the furniture door.
This will allow a 5mm gap from the top of the furniture
door to the underneath of the worktop.
4. Mark the position of the 10 fixing points in the bracket.
Using the screws supplied, fix the mounting bracket to
the furniture door. Fully tighten the screws.
5. Hang the furniture door onto the appliance door and
using the screws supplied, secure in place (fig.4-9).
Use a suitable spanner to adjust the gap on the lower
section of the adjusting bolts. The gap should be set to
approximately 9mm.
6. Fix the lower bracket to the bottom of the furniture door
fig.4-10
and the underneath of the appliance door (fig.4-10).
7. It is possible to make minor adjustments to the position
of the furniture door using the screws on the top and
the bottom of the appliance door. Adjust the door so
that it is level.
8. Insert the cover trim to the top of the appliance – this
will slide into the slot in the mounting bracket
(fig.4-11).
Bracket
Fixing
screw
10
Securing the appliance in position
fig.4-11
1. Open the appliance door.
Cover trim
2. Using a suitably sized drill bit, drill through the three
holes in the bracket into the worktop (fig.4-12).
IMPortant: Use a drill bit suitable for the worktop
material.
3. Using the screws supplied, fix the bracket to the
underside of the worktop. Fully tighten the screws.
4. Check that the door opens and shuts without snagging.
Check that the door seals correctly.
Alternative method of securing
If your worktop is unsuitable for fixing in this manner, there
Furniture door
are 2 securing points in each hinge bracket (fig.4-13).
Using the screws supplied, fix the appliance to the adjoining
cabinet.
fig.4-12
fig.4-13
11
Electrical Supply Connection
fig.4-14
Earth: to the
terminal marked E,
coloured Green/Yellow
Your refrigerator is intended as a permanent
installation.
Connect the appliance to the electrical supply (220–240V ~
50Hz) with the plug and lead, which are fitted.
Connections to the mains supply should be in accordance
with local regulations.
Live: to the
terminal marked L,
coloured Brown
Neutral: to the
terminal marked N,
coloured Blue
WarnInG: tHIs aPPlIance MUst Be eartHeD
All external wiring must comply with the IEE Regulations
for the Electrical Equipment of Buildings. The appliance is
supplied with a 3-core cable 2m long. If a replacement cable
is fitted it must be 250V high temperature PVC (85°C), 1mm².
Should the plug not fit the socket in your home, it should be
removed and replaced with a suitable plug.
note: If the plug is fitted is not suitable, it must be cut off and
disposed of properly. To avoid the risk of electrocution, the
plug must not be left where children might find it and plug it
into a supply socket.
Three pin plugs to BS1363 with a capacity of not less than
13A must be used and fitted with a 13 amp fuse ‘ASTA’
approved to BS1362.
You MUST refit the cover after replacing the fuse. If the cover
is lost, the plug MUST NOT be used until a replacement cover
has been obtained from your supplier. The colour of the
correct fuse carrier is that of the coloured insert in the base of
the fuse recess, or stated elsewhere on the plug. Always state
this colour when ordering a replacement fuse carrier.
IMPortant: The wires in the mains lead are coloured in
accordance with the following code (fig.4-14):
Green and yellow:
Blue:
EARTH
NEUTRAL
LIVE
Brown:
12
5. Cleaning and Maintenance
Do not place food back in the freezer once it has
started to thaw.
Cleaning
Disconnect the appliance from the power supply
Set the thermostat knob to position [0] and disconnect the
before cleaning.
appliance from your mains supply.
To maintain a high performance level, occasionally clean the
condenser coils at the back of the appliance.
Leave the door to the freezer open. You can place a bowl
of warm water inside the freezer to speed up the defrost
process.
Defrost the appliance regularly. A build up of thick ice
decreases the efficiency of the appliance. You should defrost
whenever the frost reaches 5 mm thickness.
Use a sponge to mop up the defrost water that will run into
the bottom of the freezer.
To keep internal odours to a minimum it is best to periodically
clean the compartment.
IMPortant: You should place some old towels on the
flooring that is immediately in front of the appliance. In
case any defrost water comes out of the freezer and onto
the floor.
Clean the interior using warm water and bicarbonate of soda
with a soft cloth. Make sure that the interior is then dried
carefully with a suitable cloth.
Once all the ice has melted, thoroughly dry the inside of the
freezer.
Do not use harsh abrasives, or aggressive cleaners
as these can damage the interior of the appliance.
IMPortant: If the inside of the freezer is not dry, then
there will be an immediate build-up of ice when the
appliance is switched back on.
Shelves and other accessories can be cleaned in the sink
using liquid dishwashing liquid and warm water. Make sure all
soap is rinsed off and all parts are dry before replacing them
inside the appliance. Do not clean them in a dishwasher.
With dry hands, reconnect the appliance to the mains supply.
Set the thermostat knob to position [4] for 24-hours, before
returning it to the normal setting of between [2] and [3].
Always keep the door seals clean. Clean the door gasket with
warm water or a neutral detergent that leaves no residue. A
tight-sealing door gasket is critical to the efficiency of your
appliance.
Do not attempt to freeze fresh food inside the
freezer until after the 24-hours.
Do not use sharp metal objects to remove the ice
Do not spray or rinse the freezer with water or
on the freezer, as this could cause damage to the
other liquids. this could harm the electrical parts.
refrigerant system.
Use a dry cloth when cleaning near the electrical
Do not use mechanical devices (such as hair dryers)
to accelerate the defrosting process.
parts.
Do not clean the freezer with a stiff or wire brush.
Do not use an organic solvent such as detergent,
petrol, lacquer, thinners, acetone or acid.
When Not in Use
If you are not using the appliance for an extended length
of time, it is recommended that you switch off the electrical
supply, empty any food out, clean the inside of the appliance
and leave the door ajar.
to prevent your skin sticking to cold steel parts,
make sure your hands are not wet when touching
the parts.
This will save energy, and also prevent a build up of stale
odours inside.
Defrosting
The frost in the freezer compartment should be removed
periodically. Use a plastic scraper to keep down the amount
of frost that builds up.
IMPortant: The freezer should be defrosted at least twice
a year. The number of times that you need to defrost it will
depend on the setting of your thermostat and how much
food you freeze and store in the freezer.
The day before you defrost, turn the thermostat dial to
position [4]. This will make sure that the food contained in
the freezer is frozen properly.
While defrosting the appliance, remove the food from the
freezer, wrap it in several layers of paper and store it in a cool
place. The temperature rise in foods will shorten its storage
life, so the food should be used within a relatively short time.
13
6. Troubleshooting
IMPortant: If your freezer appears not to be operating properly, before contacting Consumer Services, please refer to the
checklist below.
IMPortant: If your appliance appears not to be operating
My freezer does not appear to be working / there is no
correctly, then you should disconnect it from your mains
power to my appliance
supply and then contact Consumer Services.
•
•
Check that the plug is fully inserted into the power
socket.
Do not atteMPt to rePaIr tHe aPPlIance
YoUrself.
Check that there is power to your mains supply (e.g.
that there has not been a power cut or that the fuse
has not blown).
Please note that if an engineer is asked to attend while
the product is under guarantee and finds that the
problem is not the result of an appliance fault, then you
may be liable for the cost of the call out charge.
•
•
Check that the thermostat inside the appliance has
not been turned to the [0] position.
the appliance must be accessible for the engineer
to perform any necessary repair. If your appliance is
installed in such a way that an engineer is concerned that
damage will be caused to the appliance or your kitchen,
then he will not complete a repair.
Check that your mains supply voltage, corresponds
to the voltage stated on the rating plate of your
appliance.
My freezer appears to be performing poorly
this includes situations where appliances have been tiled
in, sealed in with sealant or any installation other than
the one specified by has been completed.
•
•
•
Check that the appliance is not overloaded and that
food has not been packed too tightly into it.
Please refer to the conditions of guarantee that appear on
the warranty card that you receive with the appliance.
The thermostat setting is too low: you should turn
the thermostat up higher.
Make sure that the door is closing properly and that
the door has not been opened for a long period in
error.
•
Make sure that there is sufficient ventilation for your
appliance.
My freezer is noisy
•
The refrigerant gas that circulates the pipework of
the appliance may make a slight noise, even if the
compressor is not running.
•
If the noise worsens or the appliance gets louder
than normal check that it is levelled off correctly, that
nothing is touching the rear of the freezer and that
nothing placed inside the appliance is rattling.
Ice has formed on the inner back wall of my freezer
•
Check that food has not been pushed too far back
inside the appliance, so that it is in contact with the
inner back wall.
14
7. Warranty/After Sales Service
If consultation or technical assistance is needed, please
provide the local authorised service agent with the purchase
invoice and the product code/serial number.
The product number/serial number is located inside the
refrigerator on the top left-hand side.
The 2 years free maintenance for the operation of the
appliance started from the date of purchase of this product.
Any cosmetic damage to the appliance must be reported
within 90 days of delivery.
For in-warranty service please call: 0845 6035312.
For general enquiries please call: 0870 7895107.
15
•
Docno.608-0004 - technical data - BIfreezer
8. Technical Data
Installer: Please leave these instructions with the user.
Data BaDGe loc atIon: Front left-hand side of the freezer compartment.
coUntrY of DestInatIon: GB/IE
Dimensions
All dimensions in mm.
596
550
818-868
158-208
20-75
Ratings
electrical – voltage/frequency
220–240 V / 50 Hz
A
energy efficiency class on a scale of A (more efficient) to G (less efficient)
climate class (SN = 10–32°C, N = 16–32°C, ST = 18–38°C, T = 18–43°C)
freezer compartment star rating
temperature range (from > to)
N
*/***
< –18°C
Gross capacity
108 litres
91 litres
net capacity
freezer capacity / 24 hours
9kg / 24 hours
208kWh / year
0.57kWh / 24 hours
45dB(A)
energy consumption / year
energy consumption (en153)
Max noise level
Maximum storage time by power failure
5 hours
16
17
Docno.000-0001 - Back cover rangemaster
Clarence Street, Royal Leamington Spa,
Warwickshire, CV31 2AD, England.
Tel: +44 (0) 1926 457400 Fax: +44 (0) 1926 450526
E-mail: [email protected]
ANo.000-0003 E logo
|