TM
OWNER’S MANUAL
read and understand this entire manual before riding!
Do not returnto Store!
this does not affect your statutory rights.
note: manual illustrations are for demonstration purposes only. illustrations
may not reflect exact appearance of actual product. Specifications subject to
change without notice.
Please have your 21 character product i.D. code ready before
contacting razor for warranty assistance and/or replacement parts.
Product i.D. Code: _____________ - ____________ - ____________
EN_130402
Safety WarningS
PROPER RIDING ATTIRE
WARNING: ALWAYS INSPECT SCOOTER PRIOR TO RIDING. Properly
inspecting and maintaining your scooter can reduce the risk of injury. Always
inspect your scooter before riding and regularly maintain it.
Always ensure rider is wearing proper protective equipment, such as an
approved safety helmet. A helmet may be legally required by local law or
regulation in your area. Always wear shoes and keep shoelaces tied and out of
the way of the wheels. Never ride barefoot or in sandals.
WARNING: CHECK LOCAL LAWS REGARDING SCOOTER USE. Check
local laws and regulations to see where and how you may use your Razor
scooter legally. In many states and local areas scooter riders are required
BY LAW to wear a helmet. Check local laws and regulations regarding laws
governing helmet use and scooter operation in your area.
FAILURE TO USE COMMON SENSE AND HEED THE ABOVE WARNINGS
FURTHER INCREASES RISK OF SERIOUS INJURY. USE AT YOUR OWN RISK
AND WITH APPROPRIATE AND SERIOUS ATTENTION TO SAFE OPERATION.
USE CAUTION.
Beforeyou Begin
Remove the contents from box. Inspect the contents of the box for scratches in the paint and/or dents that may have
occurred during shipping. Because your scooter was partially assembled and packed at the factory, there should not be
any problems, even if the box has a few scars or dents.
Warning: DO
NOT USE NON-RAZOR
PRODUCTS WITHYOUR
SCOOTER.
The RDS has been built to certain
Razor design specifications. The
original equipment supplied at the
time of sale was selected on the
basis of its compatibility with the
frame, fork and all other parts.
Certain aftermarket products may
not be compatible and will void
your warranty.
Grips
Riser
Handlebar
Down Tube
Collar Clamp
PRODUCT I.D. CODE
1. Side of deck
2. UPC Side of Box
Rear Fender/Brake
Front Fork
Deck
q requiredtools for assembly
5 mm Allen wrench
(Included)
2
aSSemBly inStruCtionS
q attaching the Handlebar
Warning: Failure to
properly install and tighten the
clamp may cause the rider to lose
control and fall. If you are having
difficulty understanding these
instructions, please contact Razor
Customer Service for assistance.
Tools Required: 5 mm Allen Wrench
1 Using a 5 mm Allen wrench,
loosen the bolts on the collar
clamp and slide clamp upward
on the handlebar. With a
twisting motion, push the
handlebar onto the fork until it
bottoms out on the fork headset
lock nut.
2 With the front wheel pointed
straight ahead, the handlebars
square to the front wheel and
the Razor logo facing the front,
tighten the clamp as shown.
Alternately tighten each bolt
until securely tightened.
q inflatingtires
Warning: Inflate the
tires to the recommended pressure
(60 PSI) before riding. Do not exceed
the tires’ PSI rating. Over inflation
will cause a rupture and under
inflation may cause additional wear
on the tire.
The tires are inflated when shipped, but it invariably may lose some pressure between the point of manufacturing and
your purchase. Always inflate tire to the correct PSI before first time use.
1Using a bicycle-style tire
pump equipped for a Schrader-
type valve, inflate the front tire
to the correct PSI indicated on
the sidewall of the tire.
3
rePairanD maintenanCe
q replacing thetires/tubes
Tools Required: 5 mm Allen Wrench
Nuts
Bearings
Wheel Hub
Fastener Bolts
1 Completely deflate the tire. Use
a 5 mm Allen wrench to remove the
four bolts on the hub. Remove the
worn/damaged tire or inner tube
and replace it with a new one.
Note: Be careful not to lose the
four nuts on the opposite side of
the hub.
2 Assemble the hub using the
diagram at right. Tighten bolts
using 5 mm Allen wrench.
Inner Tube
Bearings
Tire
Re-inflate. (Do not exceed 60 PSI.)
q replacing the Wheels
Tools Required: 5 mm Allen Wrench
1 Front wheel sequence.
2 Securely tighten the bolt
as shown.
3 Rear wheel sequence.
4 Securely tighten the bolt
as shown.
4
CHeCk Before riDing
q Collar Clamp
q tires
Using a 5 mm Allen wrench, check that the clamp bolts are tightened securely.
Check the pressure of your tires and inspect them for any signs of damage.
Check your front and rear bolts to ensure they are tight.
q Wheels and Bearings
It is the responsibility of the owner or guardian to periodically inspect the wheels for wear and tear, the axle for
proper tightness, and bearings for side-to-side play and loose parts. When a wheel or wheel bearing develops
play, this is an indication of excess wear and replacement is necessary. Replace immediately with only genuine
Razor replacement wheels. Worn wheels/bearings are considered normal wear and tear and are not covered by the
Warranty. Other manufacturers’ wheels may not be compatible with your RDS scooter, may affect your safety and
will void your warranty.
q Cleaningyour Scooter
Wipe with a damp cloth to remove dirt and dust.
Do not use industrial cleaners or solvents as they may damage the surfaces. Do not use alcohol, alcohol-based or
ammonia-based cleaners as they may damage or dissolve the plastic components or soften the decals or decal
adhesive. To clean grip tape, use a wet coarse bristle brush to scrub any dirt stuck to the surface and let dry.
Warning: Wheelies
and other stunt-type riding
reduces your ability to maneuver
and control your scooter. Take
the necessary precautions,
such as wearing appropriate
protective gear and practice in
an area safe for stunt riding and
free from obstructions.
q How to ride
Place one foot on the baseboard, push forward with the other foot. Steer. For enhanced cornering, lean slightly
into the direction of the turn. For controlled stops, apply the brake by stepping on the rear fender/brake. Practice
applying the brake at various speeds and in an open area free from obstructions before riding around others.
5
Safety reminDerS
Pre-riDe CHeCkliSt
loose Parts /tire Care
Be Careful!
Check and secure all fasteners before every ride. Make
You will see people on TV and maybe even people you know doing
qsure the collar clamp is locked properly in place before riding. q tricks and stunts. These are people who have been practicing on
Inspect tires for signs of wear or damage. Measure and
adjust the PSI of the tires accordingly. Do not exceed 60 PSI.
scooters for a very long time. Don’t try something until you are
ready. Avoid steep inclines and don’t ride too fast — you can lose
control and fall. Never ride in traffic or on the street and watch
your surroundings for pedestrians, bikers, boarders and skaters.
replacement Parts
Replace worn or broken parts immediately. Visit
Maintain a hold on the handlebars at all times.
Safety gear
Always wear proper protective equipment, such as an approved
q safety helmet, elbow pads and kneepads. Always wear shoes
(lace-up with rubber soles). Keep shoelaces tied and out of the
way of the wheels and never ride barefoot or in sandals.
Do not return to Store
this does not affect your statutory rights.
failure to follow these instructions may damage
your product and void your warranty.
Warranty
razor limited Warranty
The Razor RDS does not come with an extended warranty. If you have
The manufacturer warranties this product to be free of manufacturing defects
for a period of 6 months from date of purchase. This Limited Warranty does
not cover normal wear and tear, or any damage, failure or loss caused by
improper assembly, maintenance, or storage.
purchased an extended warranty, it must be honored by the store at which it
was purchased.
For your records, save your original sales receipt with this manual.
_______________________________________________________
This Limited Warranty will be void if the product is ever
• used in a manner other than for recreation;
• modified in any way;
• rented.
The manufacturer is not liable for incidental or consequential loss or damage
due directly or indirectly to the use of this product.
CuStomer SerViCe info
Printed in China for Razor USA LLC.
UNITED STATES MAILING ADDRESS:
RAZOR USA LLC
DISTRIBUTED IN THE UK BY:
re:creation Ltd,
DISTRIBUTED IN AUSTRALIA BY:
FUNTASTIC LIMITED.
P.O. Box 3610
Cerritos, CA 90703
Tel: 866-467-2967
2 Meadows Business Park
Station Approach
Blackwater
Camberley
Surrey
Level 2
Tower 2
Chadstone Place
1341 Dandenong Rd
Chadstone
GU17 9AB
3148
Tel: 0118 973 6222 Fax: 0118 973 6220
Email: [email protected]
Customer Service: 1800 244 543
Copyright © 2003 - 2013 Razor USA LLC. All rights reserved. RAZOR and the Razor Logo
Design are among the registered trademarks of Razor USA LLC in the United States and/or
select foreign countries.
EN_130402
7
|