RF-RBWSO2 Wireless Outdoor Speaker
Please read before setting up your system.
Package contents
Every Rocketboost network must contain at least one hub device, which directs network data traffic and helps devices join the
network. The network can have only one hub, which you can enable using the Hub switch on the back of all Rocketboost
transmitters. See your User Guide for instructions on“joining”devices to the network. If this is your first Rocketboost product you
should make this unit the hub, if you already have Rocketboost products, you should disable the hub mode on this device.
3.5mm stereo
3 Establishing Communication
DC adapter
for wireless
speaker
female to 2-RCA male
If this is your first Rocketboost product and you do not have an existing Rocketboost
network, the devices were joined at the factory. You do not need to join them. If you are
adding these devices to an existing network, change the hub mode switch on the sender
to Disabled and then join BOTH devices to your existing hub.
cable (6 inches/15.25 cm)
IR remote
IMPORTANT: Hub units must always have power for your network to operate. The device may be placed in standby, but the unit
must remain plugged into the wall to operate your network.
ser Guide
U
1 Getting Started
TX LED
Load batteries in wireless speaker
Charge your wireless speaker
Connect the DC adapter to the wireless speaker and plug into an AC
power outlet. The CHARGE LED blinks green while it is charging. The
light will be solid when charging is complete.
(Installing batteries is optional)
Quick
Setup Guide
DC adapter
for transmitter
A
B
Unscrew the bottom cover ( 3 screws).
Insert eight alkaline or rechargeable NiMH batteries
User Guide
Sender
3.5 mm
Wireless speaker
matching +/- as indicated. This product will only recharge
NiMH batteries. Do not attempt to charge any other
batteries in this product. Note: Your wireless speaker can
operate on batteries or with the DC to AC adapter (provided).
The unit will charge and play simultaneously.
stereo cable
Note: For the first time,
charge batteries for
16 hours.
Front controls
Use this procedure only if you need to rejoin the transmitter and speaker. This procedure
is not required for normal operation as devices were joined at the factory. To connect
these devices to an existing hub device that you own, follow the same instructions: Join
the sender/receiver to your existing hub, then join the wireless speaker to your existing
hub. Note: You can only join devices to the hub unit (the one with the green LED).
Rocketboost device
Transmitter
#
1
2
3
4
5
6
7
Feature
Power/Join button
15V DC
C Replace the cover and fasten the three screws.
Caution: Only use the
Power/Join indicator (Blue/Green Light)
Standby indicator (Red Light)
IR sensor window
Wireless speaker
supplied power adapter
8 rechargeable or alkaline
C batteries (not included)
TM
BASS
TM
15V DC
and make sure your outlet
A Set the HUB STATUS switch to ENABLE if this is your first Rocketboost product set.
• The LED lights green when the HUB STATUS switch is set to ENABLE.
• The LED lights blue when the HUB STATUS switch is set to DISABLE.
matches the AC’s input
Source button
Receiver-mode indicator (Blue Light)
Sender-mode indicator (Blue Light)
of 100-240 V.
4
1
2
3
5
6
7
Wireless speaker’s
back panel
B
Press and hold the button on the sender/receiverfor more than three seconds to
put it into joining mode. The LED starts blinking rapidly and the unit will stay in Join
mode for 30 seconds.
Press the Power/Join button on the wireless speaker for more than three seconds
so the sender and wireless speaker will enter connection mode.
• The LED lights steadily if the link is activated between both of the units.
• The LED blinks at a slower rate if the communication link is not successful.
Front Panel
x 8
Speaker
Front Panel
POWER /JOIN
/
#
Feature
Volume increase/decrease dial
C
6
1
BASS
2 Connecting the Transmitter
Power/on standby/Join button
Source
2
3
7
8
CHARGE
1
Connect to an audio source
VOL
VOL
OR
Middle-treble reflex hole
Bass reflex hole
4
D Once the link is established, if the Source LED on the wireless speaker is not
illuminated, press the Source button to toggle to the next source. If the LED is still
not illuminated, check that your source is powered up.
Connect one end of the audio cable (supplied) to
the AUDIO IN jack on the sender and the other end
to the audio output jack of your device (such as an
A/V receiver, PC, or iPod.)
3
2
5
4
4
5
Power/Join indicator (Red/Blue light)
BASS indicator
6
CHANNEL
L - MONO - R
7
For further details, see instructions in the user manual for joining new devices to an
existing Rocketboost network.
9
12
Note: If you are adding this sender to an existing network,
set the hub switch to Disable and follow the instructions
under Establishing Communication to add the transmitter
and speaker to your existing network. Otherwise, leave it
on Enable as the transmitter and wireless speaker were
pre-configured at the factory and you will not need to go
through the Establish Communication steps. Remember to
turn the volume up on the source device to at least 80%
of its maximum volume.
Charge indicator
SOURCE
8
10
11
Channel MONO (L/R) indicators
Audio source signal indicator
DC adaptor in
9
Supplied
Supplied
5
10
11
12
4 Listening to Music
Bass Boost
To listen to music:
To audio
output jack
To audio
output jack
A Turn on the sender and the wireless speaker. Make sure that the wireless
speaker is fully charged (if using Batteries) and there is an active link
between the sender and the wireless speaker. An active link will be
indicated by the Power LED showing a solid blue.
Adjust antennas
Pull up the antennas
For best results, adjust the antennas to
vertical. In some instances, you may
improve range by rotating both
antennas 45 degrees to create a 90°
angle similar to a wide "V".
B Make sure the volume is turned up to about 80% of maximum volume.
C Adjust the volume level on your wireless speaker. If you have multiple
streams in your Rocketboost network, press the Source button on the
wireless speaker to hear the next stream.
Connect the AC Adapter
Connect one end of the adapter to the DC IN jack, then
plug the other end into an AC power outlet. The standby
indicator turns red.
Repeated pressing of the SOURCE button will toggle through available
sources.
Preparing the remote control
To activate the battery:
Remove the tab from the bottom of the remote control to enable the battery.
ENGLISH 09-0536
Note: Make sure that the power outlet is 100-240V, and do not
connect the AC adapter until all other connections are completed.
QUICK SETUP GUIDE
|