10/100M Fast Ethernet Switch 5/8 port
RC-405X/RC-406X
User Manual
10/100M Fast Ethernet Switch 5/8 port RC-405X/RC-406X
User Manual
y
y
y
y
y
y
y
y
y
y
Store-and-forward switching improves overall network performance
Supports full-duplex switching bandwidth modes, allowing data rates of 10, 20 and 100Mbps
Full-duplex transfer mode / half-duplex adaptive
Provides packet switching functions between all sixteen 10/100Mbps Ethernet ports
10/100Mbps auto-sensing and negotiation allows flexibility between network devices
Wire-speed forwarding: 148,800pps/100Mbps and 14,880pps/10Mbps
High-performance memory bandwidth and expansion bus
Supports the spanning tree protocol, eliminating network loops
Supports broadcast storm control function
Supports port trucking and load sharing for high-performance servers and inter-switch links. Provides a convenient
uplink port for cascading hubs
y
y
Auto-partitioning and data collision control
Auto-polarity detection
Specification
y
y
y
y
Network standards: IEEE 802.3, IEEE 802.3u, IEEE 802.3x
Interface Media 10Base-T: 3 or 3 more than UTP, 100Base-TX: 5 types of UTP
Instructions for each panel port: Link / Act (to connect / work), 10/100Mbps (speed), other: Power (Power)
Environmental standard operating temperature: 0 ℃ -40 ℃, Storage temperature: -40 ℃ -70 ℃, Operating
Humidity: 10% -90% RH non-condensing,
y
y
Storage humidity: 5% -90% RH non-condensing
Dimensions (mm): 5-port: 91.5(L)*82(W)*27(H) mm
8-port: 163(L)*95(W)*28(H) mm
y
Power Supply: 9V 0.5A
Figures of Product
Front Panel
The unit front panel provides a simple interface monitoring the Switch. It includes a power led and 5/8 led indicator for
each port.
y Rear Panel
y Side Panel
5-port
2
10/100M Fast Ethernet Switch 5/8 port RC-405X/RC-406X
User Manual
5-port Switch’s Uplink Port
An uplink port is simply an Ethernet port where the Receive (Rx) and the Transmit (Tx) signals are swapped by crossing
the Transmit and Receive twisted-pair wires.
This will let the Transmit signal (and twisted-pair) on RC-405X correctly connect to the Receive connection on the other
device and vice-versa, allowing for stacking similar devices, or simply expanding the number of ports.
NOTE TO USERS OF 10/100 5-PORT SWITCH: If you connect a router or additional switch to the Uplink port, then you
cannot use the numbered port next to the Uplink port (port 1X on the 5-Port Switch will be inactive). The two ports are
wired together, so they cannot be used simultaneously.
y Rear Panel
8-port
5/8-Port Switch indicates a DC (9V) inlet, which accepts 100-240V 50-60Hz power adapter.
Mounting 8 Port Switch On A Wall
The 8-port 10/100Mbps Switch can also be mounted on a wall. Four mounting slots are provided on the bottom of the
switch for this purpose. Please make sure that the front panel is exposed in order to view the LEDs. Please refer to the
illustration below:
1. Mounting on a cement wall
1. Mount the Nylon screw anchors into a cement wall.
2. Drive the T3x15L screws into the Nylon screw anchors
3. Hook the mounting holes of the switch back on the screws; you have completed the wall-mount
2. Mounting on a wood wall
1. Drive the T3x15L screws into the wood wall.
2. Hook the mounting holes of the switch back on the screws; you have completed the wall-mount
3. Note: For the minimum length of the screws
1. 3/4 inch minimum for wood wall.
2. 3 inch minimum for cement wall.
Thank you for purchasing a quality Rosewill Product.
Rosewill Customer Service: 1-800-575-9885 or at [email protected]
3
|