Owner’s Manual
RX-1050
AM/FM Stereo Receiver
AM/FM STEREO RECEIVER RX-1050
POWER
TREBLE
SPEAKER
TUNING
BAND
PHONO
CD
TUNER
TAPE VIDEO
1
A
TUNE/
PRESET MONO MEMORY
PHONES
BASS
VIDEO
2
VIDEO
3
VIDEO
4
ZONE
REC
B
Important Safety Instructions
WARNING: There are no user serviceable parts inside. Refer
all servicing to qualified service personnel.
WARNING: To reduce the risk of fire or electric shock, do not
expose the unit to moisture or water. Do not allow foreign
objects to get into the enclosure. If the unit is exposed to moisture,
or a foreign object gets into the enclosure, immediately dis-
connect the power cord from the wall. Take the unit to a qualified
service person for inspection and necessary repairs.
Read all the instructions before connecting or operating the component.
Keep this manual so you can refer to these safety instructions.
Heed all warnings and safety information in these instructions and on the
product itself. Follow all operating instructions.
Clean the enclosure only with a dry cloth or a vacuum cleaner.
You must allow 10 cm or 4 inches of unobstructed clearance around the
unit. Do not place the unit on a bed, sofa, rug, or similar surface that could
block the ventilation openings. If the unit is placed in a bookcase or cabi-
net, there must be ventilation of the cabinet to allow proper cooling.
Keep the component away from radiators, heat registers, stoves, or any
other appliance that produces heat.
The unit must be connected to a power supply only of the type and voltage
specified on the rear panel. (USA: 115 V/60Hz, EC: 230V/50Hz)
Connect the component to the power outlet only with the supplied power
supply cable or an exact equivalent. Do not modify the supplied cable. Do
not defeat grounding and/or polarization provisions. The cable should be
connected to a 2-pin polarized wall outlet, matching the wide blade of the
plug to the wide slot of the receptacle. Do not use extension cords.
Do not route the power cord where it will be crushed, pinched, bent, ex-
posed to heat, or damaged in any way. Pay particular attention to the power
cord at the plug and where it exits the back of the unit.
The power cord should be unplugged from the wall outlet if the unit is to be
left unused for a long period of time.
Immediately stop using the component and have it inspected and/or ser-
viced by a qualified service agency if:
• The power supply cord or plug has been damaged.
• Objects have fallen or liquid has been spilled into the unit.
• The unit has been exposed to rain.
• The unit shows signs of improper operation
• The unit has been dropped or damaged in any way
NOTE TO CATV SYSTEM INSTALLER: Call the CATV system or antenna
installer’s attention to Article 820-40 of the NEC. This provides guidelines
for proper grounding and, in particular, specifies that the cable ground
shall be connected to the grounding system of the building, as close to the
point of cable entry as practical. See installation diagram.
NOTE: This equipment has been tested and found to comply with the lim-
its for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against interference
in a residential installation. This equipment generates and can radiate ra-
dio frequency energy and, if not installed and used in accordance with the
instructions, may cause interference to radio or TV communications. There
is no guarantee that interference will not occur in a particular installation.
If this equipment does cause interference to radio or television reception,
which can be determined by turning the equipment off and on, try to cor-
rect the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the unit and the television tuner.
Connect the unit to an AC power outlet on a different electrical circuit.
Consult your authorized Rotel retailer for assistance.
RX-1050 AM/FM Stereo Receiver
4
English
1: Controls and Connections
1
2
5
3
4
6
AM/FM STEREO RECEIVER RX-1050
POWER
TREBLE
BASS
SPEAKER
TUNING
BAND
PHONO
CD
TUNER
TAPE VIDEO 1
A
TUNE/
PRESET MONO MEMORY
PHONES
VIDEO 2 VIDEO 3 VIDEO 4 ZONE
REC
B
12
7
8
9
10 11
13
14 15
19 20 21 22 23
24
16
17
18
25
CAUTION
SWITCHED 200W MAX
ZONE
REM
EXT
12V TRIG
OUT
ZONE
OUT
2
RISK OF ELECTRIC SHOCK
DO NOT OPEN
REM
SURROUND SOUND RECEIVER
MODEL NO. RX-1050
POWER CONSUMPTION: 500 WATTS
RIGHT
LEFT
L
1
AM
LOOP
COMPUTER
I/O
R
2
1
2
IR
OUT
A
SPEAKERS
B
SPEAKER IMPEDANCE MINIMUM
OR OHMS PER SPEAKER
AND
PRE
OUT
MON
IN
MON
OUT
VIDEO 1
IN OUT
VIDEO 2
IN OUT
VIDEO 3 VIDEO 4
PHONO
CD
TAPE
OUT
A
A
B
4
ANTENNA
IN
B
8
OHMS PER SPEAKER
LEFT
RIGHT
L
L
L
GND
R
R
R
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTICAL SHOCK,
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
26
27
28
29
30
31
32
33 34 35
36
5
2: RR-939B Remote Control
3: Antenna Connections
AUD
SAT
CD
TV
TAPE
VCR
DVD
CBL
A
J
POWER
B
C
VOL
CH
BAND
K
MUTE
T / V
SURROUND +
GUIDE
ON SCREEN
MENU
D
PAUSE
C. DELAY
L
ZONE
REM
EXT
12V TRIG
OUT
ZONE 2
OUT
REM
SURROUND SOUND RECEIVER
MODEL NO. RX-1050
POWER CONSUMPTION: 500 WATTS
TRACK Ð
TRACK +
DOWN
M
L
1
AM
LOOP
COMPUTER
I/O
PLAY
SEL
R
2
UP
1
2
IR
OUT
STOP
DYNAMIC
E
PRE
OUT
MON
IN
VIDEO 1
IN OUT
PHONO
CD
TAPE
OUT
PRE
CH
ANTENNA
IN
RECALL
OPN/CLS
SUR-DELAY
L
L
L
MOVIE FILT
PROG
1
DISC 1
2
DISC 2
3
DISC 3
GND
R
R
R
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, a
(2) this device must accept any interference received
including interference that may cause undesired oper
4
DISC 4
5
DISC 5
6
DISC 6
5.1 CH
TIME [REVIEW]
F
7
8
0
9
SELECT
CLEAR [SCAN]
N
10
ENTER
BACK
RANDOM [REPEAT]
G
H
PHONO
CD
TUNER
VIDEO 4 AUX/V5
TAPE 1
M 1
TAPE 2 VIDEO 1 VIDEO 2 VIDEO 3
M 4
M 2
M 3
[SHIFT]
ZONE
LIGHT
O
I
RR-939B
RX-1050 AM/FM Stereo Receiver
6
English
4: Input Connections
DVD
CD
ROTEL RX-1050
CAUTION
SWITCHED 200W MAX
ZONE
REM
EXT
12V TRIG
OUT
ZONE
OUT
2
RISK OF ELECTRIC SHOCK
DO NOT OPEN
REM
SURROUND SOUND RECEIVER
MODEL NO. RX-1050
POWER CONSUMPTION: 500 WATTS
RIGHT
LEFT
L
1
AM
LOOP
COMPUTER
I/O
R
2
1
2
IR
OUT
A
SPEAKER IMPEDANCE MINIMUM
PRE
OUT
MON
IN
MON
OUT
VIDEO 1
IN OUT
VIDEO 2
IN OUT
VIDEO 3 VIDEO 4
PHONO
CD
TAPE
OUT
SPEAKERS
B
A
OR
B
4
OHMS PER SPEAKER
ANTENNA
IN
A
AND
B
8
OHMS PER SPEAKER
RIGHT
LEFT
L
L
L
GND
R
R
R
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTICAL SHOCK,
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
VCR
TAPE
7
5: Output Connections
B
A
TV
A
ROTEL RX-1050
CAUTION
SWITCHED 200W MAX
ZONE
REM
EXT
12V TRIG
OUT
ZONE
OUT
2
RISK OF ELECTRIC SHOCK
DO NOT OPEN
REM
SURROUND SOUND RECEIVER
MODEL NO. RX-1050
POWER CONSUMPTION: 500 WATTS
RIGHT
LEFT
L
1
AM
LOOP
COMPUTER
I/O
R
2
1
2
IR
OUT
A
SPEAKERS
B
SPEAKER IMPEDANCE MINIMUM
OR OHMS PER SPEAKER
AND
PRE
OUT
MON
IN
MON
OUT
VIDEO 1
IN OUT
VIDEO 2
IN OUT
VIDEO 3 VIDEO 4
PHONO
CD
TAPE
OUT
A
A
B
4
ANTENNA
IN
B
8
OHMS PER SPEAKER
LEFT
RIGHT
L
L
L
GND
R
R
R
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTICAL SHOCK,
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
AMPLIFIER
RX-1050 AM/FM Stereo Receiver
8
6: Zone 2 Connections
CD
ROTEL RX-1050
CAUTION
SWITCHED 200W MAX
ZONE
REM
EXT
12V TRIG
OUT
ZONE
OUT
2
RISK OF ELECTRIC SHOCK
DO NOT OPEN
REM
SURROUND SOUND RECEIVER
MODEL NO. RX-1050
POWER CONSUMPTION: 500 WATTS
RIGHT
LEFT
L
1
AM
LOOP
COMPUTER
I/O
R
2
1
2
IR
OUT
A
SPEAKER IMPEDANCE MINIMUM
PRE
OUT
MON
IN
MON
OUT
VIDEO 1
IN OUT
VIDEO 2
IN OUT
VIDEO 3 VIDEO 4
PHONO
CD
TAPE
OUT
SPEAKERS
B
A
OR
B
4
OHMS PER SPEAKER
ANTENNA
IN
A
AND
B
8
OHMS PER SPEAKER
RIGHT
LEFT
L
L
L
GND
R
R
R
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTICAL SHOCK,
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
AMPLIFIER
ZONE 2 IR
RIGHT
LEFT
9
English
Tuning Controls ....................................12
BAND Button
AC Power Connections ..........................16
Contents
AC Input
................................................... 16
TV/BAND Button
....................................... 12
................................... 13
.............................. 13
Boxed numbers refer to RX-1050 illustration.
Boxed letters refer to RR-939B illustration.
Accessory Power Outlets
(North American version)................................. 16
TUNING Buttons
CH TUNING Buttons
12V TRIGGER Connections
......................... 16
TUNE/PRESET Button
[SHIFT] TV Button
1: Controls and Connections ............................... 4
2: RR-939B Remote Control ............................... 5
3: Antenna Connections ..................................... 5
4: Input Connections .......................................... 6
5: Output Connections ........................................ 7
6: Zone 2 Connections ....................................... 8
Miscellaneous Connections ....................16
EXTERNAL REM IN
..................................... 16
................................ 16
NUMERIC Buttons:
Station Presets
.......................................... 13
COMPUTER I/O Input
DIRECT FREQUENCY/10 Button
................. 13
Zone 2 Connection and Operation..........16
Zone 2 Power On/Off Operation ...................... 17
Controlling Zone 2 from the Main Room
Preset Scanning
[SHIFT] MUTE Buttons
........................ 13
MONO Button
........................................... 14
About Rotel .........................................10
ZONE Button
............................................. 17
FL Display Control ................................14
Turning the FL Display On/Off
Controlling Zone 2 from the Remote Location... 17
Getting Started ....................................10
Key Features ................................................... 10
Unpacking ....................................................... 10
Placement ....................................................... 10
Zone 2 Audio Outputs
ZONE REM IN Jack
............................... 17
SELECT Button
........................................... 14
.................................... 17
Custom Display Labels
MENU Button
IR OUT Jacks
............................................. 18
SEARCH +/– Buttons
PLAY/SEL Button
Protection Circuit..................................18
RR-939B Remote Control .....................11
Operating the RR-939B
....................................... 14
Specifications .......................................18
Audio .............................................................. 18
Video ............................................................... 18
FM Tuner ......................................................... 18
AM Tuner ......................................................... 18
General ........................................................... 18
Restoring the FL Display Labels
............................................. 14
AUDIO Button
Programming the RR-939B
SHIFT Button ............................................. 11
........................................... 11
................ 11
Rear Panel Connections ........................14
Phono Inputs
Basic Controls ......................................11
Phono Ground
.......................................... 14
POWER Button
.................................... 11
.......................................... 11
................................... 11
................................... 12
CD Inputs
.................................................. 14
Remote Sensor
Front Panel Display
Master Volume
Tape Inputs and Outputs
VIDEO 1 – 2 Inputs/Outputs
VIDEO 3 – 4 Inputs
............................ 14
.............. 14
............................ 15
MUTE Button
............................................. 12
............................................ 12
...................................... 12
TV Monitor Output
Speaker Outputs
PRE OUT/MAIN IN
..................................... 15
....................................... 15
..................................... 15
Tone Controls
Headphones Jack
Speaker Buttons and LEDs
......................... 12
Antenna Connections ............................15
MEMORY Button
Input Source Buttons
REC Button
........................................ 12
.......................... 12
AM Loop Antenna
FM Wire Antenna
...................................... 15
...................................... 15
ZONE Button
............................................. 12
RX-1050 AM/FM Stereo Receiver
10
Placement
About Rotel
Getting Started
Thank you for purchasing the Rotel RX-1050
AM/FM Stereo Receiver. The RX-1050 is three
products in one:
Place the RX-1050 on a solid, dry, level sur-
face away from direct sunlight, excessive heat,
high humidity, or strong vibrations.
A family whose passionate interest in music
led them to manufacture high fidelity compo-
nents of uncompromising quality founded Rotel
over 40 years ago. Through the years that
passion has remained undiminished and the
family goal of providing exceptional value for
audiophiles and music lovers regardless of their
budget, is shared by all Rotel employees.
The RX-1050 can generate considerable heat
during normal operation. Do not block its
ventilation openings. Allow a minimum of 10
cm (4 inches) of unobstructed open space
around the unit. If installed in a cabinet, make
sure that there is adequate ventilation.
• Full-featured audio/video control center for
analog audio and video source components
• A high-quality AM/FM tuner with 30 sta-
tion presets, direct access tuning, and auto-
tuning.
The engineers work as a close team, listen-
ing to, and fine tuning each new product until
it reaches their exacting musical standards.
They are free to choose components from
around the world in order to make that prod-
uct the best they can. You are likely to find
capacitors from the United Kingdom and
Germany, semi conductors from Japan or the
United States, while toroidal power transformers
are manufactured in Rotel’s own factory.
Make sure the RX-1050 is close to the other
components in your audio/video system and,
if possible, place it on its own shelf. This will
make initial cable routing, hookup, and any
subsequent system changes easier. It also
minimizes potential interference or heat buildup
from other components.
• A high power 2-channel amplifier.
Key Features
• Rotel’s Balanced Design Concept combines
advanced circuit board layout, comprehen-
sive parts evaluation, and extensive listening
tests for superior sound and long term re-
liability.
Make sure there is enough room behind the
RX-1050 for easy hookup. Remember, you are
connecting many other components to this unit
and you’ll probably need more space than you
think.
• Independent selection of source inputs for
listening and recording.
Rotel’s reputation for excellence has been
earned through hundreds of good reviews and
awards from the most respected reviewers in
the industry, who listen to music every day.
Their comments keep the company true to its
goal - the pursuit of equipment that is musi-
cal, reliable and affordable.
• Zone 2 output with independent input se-
lection and volume adjustments for multi-
zone custom installations along with IR-
repeater capability for operation from the
remote zone.
Don’t stack other objects (components or other
items) on top of the RX-1050. Don’t let water
fall into the RX-1050 as this could damage
delicate circuitry.
All of us at Rotel, thank you for buying this
product and hope it will bring you many hours
of enjoyment.
• Customizable labels for source inputs.
• A and B speaker outputs
We suggest you look over the RX-1050’s front
and rear panels before you start connecting
other components. The explanations in this
manual will help you get familiar with the unit’s
connections, features, and controls.
• Headphone output.
• Preout and Main In connections.
Most functions are duplicated on the front-panel
and on the remote. A few are found only on
one or the other. Throughout this manual, num-
bers in gray boxes refer to the RX-1050 illus-
tration at the front of this manual. Letters refer
to the RR-939B remote illustration. When both
appear, the function is found on both the
RX-1050 and the remote. When only one ap-
pears, that function is found only on the
RX-1050 or the remote.
• Universal remote control to operate the
RX-1050 and seven other components.
Unpacking
Remove the unit carefully from its packing. Look
for the handheld remote control and other
accessories. Save the packing and box as it
will protect the RX-1050 if you move or need
to return it for maintenance.
11
English
Programming the RR-939B
RR-939B Remote Control
Basic Controls
The RX-1050 includes a handheld remote
control that does far more than operate the
RX-1050. The RR-939B is a full-function pro-
grammable remote control that can operate
up to 8 audio/video components.
The RR-939B is preprogrammed from the fac-
tory to operate the RX-1050. Should the AU-
DIO command set on your RR-939B not op-
erate the RX-1050, it’s possible that the pro-
gramming has been inadvertently changed.
To program the remote to operate the
RX-1050, set the AUDIO Code = 001:
POWER Button
The front-panel POWER switch on the RX-1050
is a master power control. It must be pressed
IN for the unit to operate. When it is in the
OUT position, the unit is fully off and cannot
be activated from the remote control. The
POWER switch on the remote functions as a
standby switch, activating or deactivating the
unit. In standby mode, minimal power is still
supplied to memory circuits to preserve set-
tings. When the unit has AC power applied
and the front-panel POWER button is pressed
IN, the front-panel POWER LED lights, regard-
less of whether the unit is in standby mode or
fully-activated in the main room. In normal
operation, use the STANDBY switch to deac-
tivate the unit when you are finished listening
and leave the POWER switch ON at all times.
This will preserve memory functions.
A separate manual, included with the remote,
gives detailed information on programming
and using the RR-939B to replace all of the
remote controls in your system. This section is
intended to provide only that information which
pertains to the use of the RR-939B to operate
the RX-1050.
1. Press the AUDIO
button at the top of
the remote while simultaneously pressing
the MUTE button and hold both for at least
one second. The AUDIO button will light
in red for 20 seconds, indicating that you
have entered the program mode. The next
step must be done within this 20 second
period, or the RR-939B will revert to its
standard operating mode.
NOTE: Many functions duplicate the RX-1050
front panel controls and are listed here only
for your reference. Please refer to the previ-
ous Front Panel Controls section of this manual
if you need additional information.
2. Use the NUMERIC
buttons to enter the
3-digit code (001) for the RX-1050 – press
0, then 0, then 1. The AUDIO button will
flash each time you enter a digit.
Operating the RR-939B
AUDIO Button
3. Store the code number by pressing the cor-
responding AUDIO button again. The button
will blink twice to confirm the storage of
the code in memory.
Remote Sensor
To operate the RX-1050 with the remote, make
sure that the AUDIO mode is active by press-
ing the AUD button on the remote before you
start. If it is active, pressing command keys
on the RR-939B will cause the AUDIO button
to flash red. Once the AUDIO mode is active,
it will stay active unless you press one of the
other DEVICE buttons to control a different
component.
This sensor receives infrared signals from the
handheld remote control. Make sure you do
not accidentally block this sensor with cables
or accessories.
SHIFT Button
The SHIFT button on the remote is used to ac-
cess secondary functions on several RR-939B
buttons. Press the SHIFT button and then the
desired button.
Front Panel Display
The large fluorescent display in the upper
portion of the RX-1050 provides status infor-
mation used in operating the AM/FM receiver
(such as station frequency display, band, preset
memory, etc.).
RX-1050 AM/FM Stereo Receiver
12
REC Button
ZONE Button
MASTER VOLUME
SPEAKER Buttons and LEDs
The MASTER VOLUME control adjusts the level
of all output channels simultaneously. Rotate the
control clockwise to increase the volume. Ro-
tate counterclockwise to decrease the volume.
MASTER VOLUME buttons are also available
on the RX-1050's handheld remote control.
The RX-1050 provides output connections for
two pairs of speakers: A and B. A pair of
SPEAKER buttons independently control which
speaker outputs, if any, are active. Press the
SPEAKER A button to activate or deactivate
the SPEAKER A outputs. Press the SPEAKER B
button to activate or deactivate the SPEAKER
B outputs.
The RX-1050 can record from any source to
a recorder connected to the TAPE, VIDEO 1,
VIDEO 2 or VIDEO 3 outputs, even while lis-
tening to a different input source. To select an
input source for recording, press the REC button
on the front-panel (or the equivalent ZONE
button on the remote). Then, press one of the
INPUT SOURCE buttons within 5 seconds to
select the signal you wish to record. After
making your selection (or if more than five sec-
onds passes), the input source buttons return
to their normal function, selecting a listening
source.
When you adjust the volume, an indicator in
the display shows the volume setting.
An LED indicator located to the left of each
button lights when that speaker output is acti-
vated.
MUTE Button
The MUTE button on the remote temporarily
turns off the output signal. Push this button once
to turn the sound off. A mute indication will
appear in the front panel display. Press the
MUTE button again to restore previous volume
levels.
NOTE: For headphone listening, deactivate
both the SPEAKER Aand SPEAKER B outputs.
Remember, this selection is independent of the
listening source. While recording, you may
select a different source (for example, the built-
in tuner) for listening. The record selection ap-
pears in the display to the right of the listen-
ing selection.
MEMORY Button
The MEMORY button is used to confirm and
memorize tuner station presets. Its use is de-
scribed in detail in the Tuning Controls sec-
tion of this manual.
TONE Controls
BASS and TREBLE controls increase and de-
crease the audio signal’s low and high fre-
quency content respectively. Rotate clockwise
to increase output in the respective frequency
range and counterclockwise to reduce it. The
center detent removes each control from the
audio path for maximum signal integrity.
Tuning Controls
The RX-1050 features a digital synthesized AM/
FM tuner with 30 station presets. Operation
of the tuning functions involves the use of six
buttons on the front panel plus the numeric and
other buttons on the remote.
Input Source Buttons
Eight buttons on the right side of the front panel
directly select an audio or video input source
(PHONO, CD, TUNER, TAPE, VIDEO 1, VIDEO
2, VIDEO 3, VIDEO 4) for listening. Push any
of these buttons (or the duplicates on the
handheld remote) to select the desired source.
You will hear this source and, if you have
selected a video source, see its picture on your
TV monitor. The left side of the front panel dis-
play shows the current source selection.
HEADPHONES Jack
BAND Button
TV/BAND Button
This jack accepts a standard 1/4 inch stereo
headphone plug. Use an adaptor if your head-
phones have a small mini-plug.
The BAND button on the front panel and the
TV/BAND button on the remote selects AM
or FM mode. Press either button to toggle back
and forth between the two modes. An indi-
cator at the left portion of the front panel dis-
play confirms your choice and the currently
tuned station frequency is shown in the main
portion of the display.
NOTE: Inserting a headphone plug does not
automatically disable all speaker outputs. Use
the SPEAKER buttons described in the next
section to turn the speakers on or off during
headphone listening.
The input source buttons can also be used (with
the REC button
described in the next sec-
tion) to select an analog input source signal
to be available at the outputs for recording.
Additionally, the input source buttons can be
used with the ZONE button
to select an
analog input source for ZONE 2.
13
English
DIRECT FREQUENCY/10 Button
TUNING Buttons
CH TUNING Buttons
TUNE/PRESET Button
[SHIFT] TV Button
If you know the frequency of the desired sta-
tion, you may tune it directly using the DIRECT
FREQUENCY/10 button and the NUMERIC
The buttons labeled TUNING on the front panel
or CH UP/DOWN on the remote control pro-
vide two different tuning functions, depend-
ing on the mode of operation.
The TUNE PRESET button toggles between
FREQUENCY TUNING mode (the CH TUN-
ING buttons advance to the next station fre-
quency) and PRESET TUNING mode (the CH
TUNING buttons advance to the next memo-
rized station preset). To change modes, press
the front panel TUNE PRESET button. To change
modes using the remote, press the SHIFT but-
ton and then the TV button. A PRESET indica-
tor in the front panel DISPLAY lights when the
PRESET mode is active.
buttons
on the remote.
1. Press the DIRECT FREQUENCY/10 button
to change the NUMERIC buttons from sta-
tion preset to frequency direct mode. The
station frequency in the front panel display
change to a series of four bars, represent-
ing the digits of a station frequency, with
the first bar flashing.
In the normal FREQUENCY TUNING
mode, press a TUNING button and release
to manually jump up or down to the next sta-
tion frequency, regardless of whether or not
a station is broadcasting on that frequency.
For auto scan tuning, press and hold the TUN-
ING button for approximately one second. An
AUTO indicator appears in the front panel dis-
play and the tuner begins automatically scan-
ning up or down through the frequencies until
the next available station is detected. If this is
not the desired station, repeat the automatic
tuning procedure to find the next station. Weak
stations will be skipped during auto tuning.
2. Enter the first digit of the station frequency
using the NUMERIC buttons. The digit
appears in the frequency display and the
second bar flashes. Enter the remaining
digits of the frequency. When all of the digits
have been entered, the tuner automatically
tunes to the displayed station frequency.
NUMERIC Buttons:
Station Presets
The RX-1050 can store up to 30 station pre-
sets for recall at any time using the NUMERIC
buttons on the remote control. To memorize
a station:
In the PRESET TUNING mode, press a
TUNING button and release to jump up or
down to the next memorized station preset.
Switch between FREQUENCY and PRESET tun-
ing modes by pressing the SHIFT button
NOTE: On the USA version, pressing 1 in
the FM mode will enter 10 as the digit in
the frequency display. On the European
version, it is necessary to press 1 and then
0 to enter 10. For US FM stations, press
only one digit following the decimal point
as shown in the first example below. For
European FM stations, press two digits fol-
lowing the decimal point as shown in the
second example.
1. Tune to the desired station, AM or FM.
2. Press the MEMORY button on the front
panel. A MEMORY indicator flashes for
five seconds in the front panel display.
and then the BAND/TV button
on the re-
3. While the MEMORY indicator is flashing,
press the number of the preset where you
wish to store the station frequency. For ex-
ample, to memorize preset 3, press the 3
button. To memorize preset 15, press the
1 button followed by the 5 button.
mote control. A PRESET indicator appears in
the display when PRESET TUNING is activated.
NOTE: Several indicators in the front panel
display assist tuning. A large display shows
the tuned frequency and increases or de-
creases during tuning. A TUNED indicator
lights when a sufficiently strong signal is re-
ceived. A ST indicator lights when a stereo
FM signal is received.
EXAMPLES:
4. A previously stored frequency is erased from
memory when a new frequency is memo-
rized for the same preset number.
(USA FM) 87.50MHz
Press 8>7>5
(Europe FM) 87.50MHz Press 8>7>5>0
(all AM) 1610kHz
Press 1>6>1>0
To tune to a previously memorized
station, just press the preset number
on the NUMERIC buttons. For example,
to tune to preset 3, press the 3 button. To tune
to preset 15, press the 1 button and then press
the 5 button.
Preset Scanning
[SHIFT] MUTE Buttons
This shift function activates a PRESET SCAN-
NING feature, playing each memorized preset
station for five seconds before moving to the
next. Using the remote, press the SHIFT but-
ton and then the MUTE button to begin scan-
ning. To stop the PRESET SCANNING on the
desired station, press the SHIFT button and then
the MUTE button.
NOTE: If the TUNER is not already the selected
INPUT SOURCE, selecting a station preset will
automatically switch to the TUNER input and
tune the memorized station.
The NUMERIC buttons can also be used for
direct access tuning (see below).
RX-1050 AM/FM Stereo Receiver
14
Once a custom label is programmed, the new
name appears when that source is selected
for either listening or recording. When the
source is selected, the original label (VIDEO
1, VIDEO 2, etc.) appears, followed by the
custom label.
MONO Button
Phono Inputs
Phono Ground
The MONO button changes the FM mode from
stereo reception to mono reception. In stereo
mode, a stereo signal will be heard if the sta-
tion is broadcasting a stereo signal and there
is sufficient signal strength. A stereo indica-
tor lights in the front panel display. In mono
mode, a mono signal will be heard even if
the station is broadcasting a stereo signal.
These inputs accept the signal from a standard
moving magnet phono cartridge. Connect the
left and right output cables of a turntable to
this pair of RCA inputs. Connect the ground
wire from your turntable to the phono ground
lug, labeled GND.
Restoring the FL Display Labels
To clear all custom labels and restore the original
defaults, turn the RX-1050 off. Then, press and
CD Inputs
NOTE: Switching to mono mode can be a use-
ful way to improve the reception of weak or
distant FM signals. Less signal strength is re-
quired for clean mono reception than for ste-
reo reception.
hold the SPEAKER B
, TUNE/PRESET
,
Connect the left and right analog outputs from
a CD player to the RCA input jacks labeled
CD.
and MONO
POWER button
buttons while pressing the
to ON.
Tape Inputs and Outputs
Rear Panel Connections
The RX-1050 provides a set of audio tape
connections (labeled TAPE) with a pair of in-
puts and a pair of record outputs that provide
a signal for recording.
FL Display Control
The RX-1050 provides rear panel connections
for four video sources, a CD, a tape deck, and
a phono input for use with a turntable. These
connections include standard RCA audio in-
puts and outputs plus composite video inputs
and outputs.
Turning the FL Display On/Off
SELECT Button
Connect the left and right analog outputs from
an audio tape deck to the TAPE IN input jacks.
Connect the TAPE OUT output jacks to the
INPUTS on the audio tape deck.
To turn the FL Display on or off, press the SE-
LECT button on the remote control. When the
display is off, pressing any control button will
turn the display on for five seconds.
The RX-1050 includes two pairs of speaker
connections for the built-in power amplifier as
well as RCA preamp outputs for use with ex-
ternal amplifiers. In addition, a composite video
output connects the unit to your TV monitor.
VIDEO 1 – 2
Inputs/Outputs
Custom Display Labels
MENU Button
SEARCH +/– Buttons
PLAY/SEL Button
There are groups of connections for up to four
video source components. Each group includes
a pair of RCA analog audio inputs at the bottom
of the group and a composite video input at
the top. Two of these groups (VIDEO 1 and
VIDEO 2) also include a set of record outputs
for sending audio and video signals to a VCR.
NOTE: DO NOT plug any system component
into anAC source until system hookup is com-
plete and you are confident that all compo-
nent-to-component connections have been
properly made.
You can program the RX-1050 to display custom
names (up to five characters long) for each
of the source inputs. For example, you could
relabel VIDEO 1 as “VCR” or VIDEO 2 as
“DVD”. To program custom labels:
All video cables should have a 75 ohm
impedance rating. Although conventional
audio interconnects will pass a video signal,
their construction and limited bandwidth im-
pose a performance penalty because, in part,
they do not adhere to the 75 ohm standard.
• Select the source input you wish to rela-
bel so the current name appears in the
display.
Connect your VCR to the VIDEO 1 group of
inputs and outputs. This set of connections
allows recording.
• Press and hold the MENU button
on
Connect the analog audio outputs of the VCR
to the VIDEO 1 IN left and right RCA audio
jacks. Connect the VIDEO 1 OUT left and right
RCA audio output jacks to the audio inputs
on the VCR.
the remote until the characters in the dis-
play change to blinking solid blocks.
When making signal connections, make sure
that you always preserve proper channel con-
sistency, i.e. connect LEFT channels to LEFT
channel jacks and RIGHT channels to RIGHT
channel jacks. All RCA-type connections on
the RX-1050 follow these standard color codes:
• Use the SEARCH +/– buttons
on the
remote to scroll through the character set.
When the desired character displayed,
press the PLAY/SEL button
Connect the RCA composite video output of
the VCR to the RCA composite video input
labeled VIDEO 1 PLAY.
to confirm
it and proceed to the next character.
Left audio: RCA jack with white inset
Right audio: RCA jack with red inset
Video: RCA jack with yellow inset
• Repeat the previous step to select the re-
maining characters. After the last charac-
ter is programmed and confirmed, the new
name is saved automatically.
Hookup the VIDEO 1 REC video output to the
RCA composite video recording input on your
VCR.
Connect your audio-only source components
to these RCA inputs and outputs:
Repeat for a second VCR video components,
using the connections for VIDEO 2.
15
English
Each pair of connectors is color-coded for
polarity: red for positive and black for nega-
tive. All speakers and all speaker wire is also
marked for polarity. For proper performance,
you must maintain this polarity at all speaker
connections. Always connect the positive ter-
minal of each speaker to the corresponding
red speaker terminal on the RX-1050 and the
negative speaker terminal to the correspond-
ing black connector on the RX-1050.
VIDEO 3 – 4 Inputs
Antenna Connections
These two audio/video inputs allow connec-
tion of additional video components such as
a play-only VCR, DVD player, LaserDisc player,
or DSS satellite receiver. There are no outputs
for sending a record out signal to these com-
ponents.
The RX-1050 requires two antennas to receive
radio signals, one for AM and one for FM.
Most users will get acceptable reception us-
ing the indoor antennas which are supplied
with the RX-1050. Instructions for hooking up
these antennas follow.
Connect the RCA analog audio outputs of the
video component to the left and right RCA
analog audio inputs labeled VIDEO 3. Then,
connect the RCA composite video output of
the video source to the corresponding RCA
composite connection labeled VIDEO 3.
NOTE: If you are located a long distance from
the radio transmitters, you may use an out-
door antenna to improve reception. Outdoor
antenna systems can be dangerous if they
are not properly grounded and should be
installed by a professional contractor famil-
iar with the electrical code requirements in
your local area.
Route the wires from the RX-1050 to the speak-
ers. Leave enough slack so you can move the
components to allow access to the speaker con-
nectors. If you are using banana plugs, con-
nect them to the wires and then plug into the
backs of the binding posts. The collars of the
binding posts should be screwed in all the way
(clockwise). If you are using terminal lugs,
connect them to the wires. If you are attach-
ing bare wires directly to the binding posts,
separate the wire conductors and strip back
the insulation from the end of each conduc-
tor. Be careful not to cut into the wire strands.
Unscrew the binding post collars. Place the
connector lug or the twisted bare wire around
the binding post shaft. Turn the collars clock-
wise to clamp the connector lug or wire firmly
in place.
Repeat using the VIDEO 4 connections for an
additional play only video component.
NOTE:Any of the video source inputs may also
be used for an audio-only source. Simply omit
the video connection.
AM Loop Antenna
The RX-1050 includes a loop antenna to re-
ceive AM radio signals. Remove this antenna
from the box and locate it near the RX-1050.
TV Monitor Output
The video output of the RX-1050 sends the video
signal to your TV monitor. Connect the TV
MONITOR output to an RCA composite video
input on your television monitor. Whatever input
source is selected on the RX-1050 will appear
on screen.
Connect the 300 ohm twin-conductor wire from
the loop antenna to the pair of screw termi-
nals labeled AM LOOP, attaching one wire
to each terminal. It does not matter which wire
attaches to which terminal, but make sure that
the connections are solid and that the two wires
do not touch.
NOTE: Be sure that no loose wire strands can
touch adjacent wires or connectors.
Speaker Outputs
You may need to rotate or otherwise reorient
the antenna to find the best position.
PRE OUT/MAIN IN
The RX-1050 has a built-in stereo amplifier for
driving left and right speakers. There are two
pairs of connections on the back panel which
allow you to connect two pairs of speakers
(A and B) and select them with front-panel
buttons.
NOTE: To use an outdoor antenna, connect its
300 ohm twin-conductor wire to the AM ter-
minals in place of the loop antenna, only af-
ter a professional contractor has installed the
antenna system in accordance with local elec-
trical codes.
The RX-1050 provides a pair of variable-level
RCA preamp audio outputs and a pair of RCA
amplifier inputs that allow you to use exter-
nal amplifiers in place of, or in addition to,
the built-in amplifiers.
NOTE: The combined speaker impedance must
be a minimum of 4 ohms. If you are driving
just one pair of speakers (A or B connections),
use speakers with a nominal impedance of 4
ohms or higher. If you are driving two pairs
of speakers (A and B) simultaneously, use
speakers rated at 8 ohms or higher.
NOTE: The preamp outputs are connected to
power amplifier inputs with jumpers in a stan-
dard PRE OUT/MAIN IN configuration. To
disable the built-in power amplifiers and use
external amplifiers, remove these jumpers.
Save them for future use.
FM Wire Antenna
The RX-1050 is supplied with a T-shaped indoor
FM antenna. Connect the attached coax F-type
plug to one of the FM antenna connectors on
the RX-1050. For best reception, unfold the T-
shaped antenna. Eyelets at both ends of the T
allow tacking the antenna to a wall, if desired.
Experiment with positioning for best reception.
To hook up the RCA audio outputs to
an external amplifier, connect a standard au-
dio cable from each output to the input of the
amplifier channel that will power the corre-
sponding speaker.
There are two sets of binding post connections
(one pair for SPEAKERS A and one for SPEAK-
ERS B) which accept bare wire, spade lugs,
or banana plug connectors (in some markets).
NOTE: To use an outdoor antenna, connect its
75 ohm coax lead wire to the FM connector
instead of the indoor wire antenna, only af-
ter a professional contractor has installed the
antenna system in accordance with local elec-
trical codes.
RX-1050 AM/FM Stereo Receiver
16
AC Power Connections
Miscellaneous Connections Zone 2 Connection and
Operation
AC Input
EXTERNAL REM IN
Your RX-1050 is configured at the factory for
the proper AC line voltage in the country where
you purchased it (USA: 115 volts/60Hz AC
or CE: 230 volts /50 Hz AC ). The AC line
configuration is noted on a decal on the back
of your unit.
This 3.5 mm mini-jack (labeled EXT REM IN)
receives command codes from an industry-stan-
dard infrared receivers (Xantech, etc.) located
in the main listening room. This feature is useful
when the unit is installed in a cabinet and the
front-panel sensor is blocked. Consult your au-
thorized Rotel dealer for information on ex-
ternal receivers and the proper wiring of a jack
to fit the mini-jack receptacle.
The RX-1050 provides Zone 2 multi-room
capability, allowing you to enjoy music and
operate the system from a second room. From
the remote location, you can select a source
component (even if different from the source
playing in the main listening room), adjust the
volume level in the remote zone, and oper-
ate the source components.
Plug the supplied cord into the AC INPUT
receptacle on the back of the unit.
To use the Zone 2 capability, you need addi-
tional components: a pair of speakers installed
in the remote zone, an amplifier to drive them,
and a third-party IR repeater system.
See the POWER SWITCH heading in the BASIC
CONTROLS section of this manual for infor-
mation about turning the unit on and off.
NOTE: The IR signals from the EXTERNAL RE-
MOTE IN jack (as well as those from the
ZONE REMOTE IN jack) can be relayed to
source components using external IR emitters
or hard-wired connections from the IR OUT
jacks. See the ZONE 2 section of this manual
for additional information.
NOTE: Memorized settings and labels will be
stored for up to one month if the RX-1050 is
disconnected from AC power.
Zone 2 can be controlled from the main room
using RX-1050’s front-panel ZONE button. Op-
eration from the remote zone requires the in-
stallation of an infrared repeater system
(Xantech, Niles, etc.) which relays infrared
remote control commands from Zone 2 to the
ZONE REMOTE IN input on the back of the
RX-1050.
Accessory Power Outlets
(North American version)
COMPUTER I/O Input
The RX-1050 has two switched outlets on the
back panel. Power is available from these
outlets when the RX-1050 is turned on. These
outlets can provide up to a total of 200 watts.
They are appropriate for supplying power to
signal sources, such as CD players, tuners, or
tape decks. They should not be used for power
amplifiers. Connecting components that will
draw more than 200 watts to these outputs
could damage the RX-1050.
The RX-1050 can be operated with a personal
computer running audio system control soft-
ware from third-party developers. This control
is accomplished by sending operating codes
(normally sent by the RR-939B remote control)
from the computer via a hard-wired network
connection.
Several points to keep in mind about the Zone
2 function:
• An infrared repeater system (Xantech, Niles,
et al) is required for operation from the
remote zone.
The COMPUTER I/O input provides the nec-
essary network connections on the back panel.
It accepts standard RJ-45 8-pin modular plugs,
such as those commonly used in 10-BaseT UTP
Ethernet cabling.
• The RR-939B remote control supplied with
the RX-1050 will operate Zone 2 if used
with a repeater system from the remote
zone. It can also be programmed to op-
erate Rotel source components via the
RX-1050's IR OUT jack.
12V TRIGGER Connections
Several Rotel amplifiers offer the option of
turning them on and off using a 12 volt trig-
ger signal. These two connections provide this
12 volt trigger signal. When the RX-1050 is
activated, a 12 volt DC signal appears at these
connectors and will turn on amplifiers. When
the RX-1050 is put in STANDBY mode, the
trigger signal is interrupted and the amplifi-
ers will turn off.
For additional information on the connections,
software, and operating codes for computer
control of the RX-1050, contact your autho-
rized Rotel dealer.
• Any source component connected to the
RX-1050's inputs can be sent to the Zone
2 outputs. ZONE 2 operates independently
of the main room. You can select a differ-
ent source or adjust Zone 2 volume with-
out affecting the MAIN outputs in any way.
• Avoid sending the same infrared command
to the RX-1050 front-panel sensor and a
Zone 2 repeater at the same time. This
means that Zone 2 must be in a different
room from the RX-1050.
17
Zone 2 Power On/Off
Operation
To change the Zone 2 input source:
When the TUNER source is not selected
in the main room, you can also access
the tuner functions (Preset, Tuning Up/Down,
Direct Preset Channel Selection, etc.) from
ZONE 2. This feature is not available when
the TUNER source is active in the main room
to avoid interrupting someone else’s listening
by changing the station.
1. Press the front-panel ZONE button. The
status of Zone 2 appears in the display.
Make sure that Zone 2 is ON.
Once master power is applied to the unit by
pressing the front-panel POWER button, the
RX-1050 provides independent power on/off
operation for both zones. Pressing the remote
control POWER button in the main room acti-
vates or deactivates the RX-1050 in the main
room only and has no effect on Zone 2. Con-
versely, activating or deactivating Zone 2 has
no effect on the main listening room. However,
placing the front-panel POWER button in the
OFF position completely shuts off the unit, for
both zones.
2. Within 10 seconds after pressing the ZONE
button, press one of the INPUT SOURCE
buttons to select a new source for Zone 2.
The name of the selected source appears
in the display.
Zone 2 Audio Outputs
3. Following 10 seconds with no commands,
the RX-1050 reverts to normal operation.
See Figure 6.
These line-level RCA outputs send the Zone 2
audio signal to a stereo amplifier driving a
pair of speakers in the remote zone.
To change the Zone 2 volume:
1. Press the front-panel ZONE button. The
status of Zone 2 appears in the display.
Make sure that Zone 2 is ON.
Controlling Zone 2
from the Main Room
ZONE Button
Although you have the option of using an in-
tegrated amplifier or a receiver to power the
remote speakers, we suggest using a fixed-
gain power amplifier. This simplifies system
installation and operation. Your authorized Rotel
dealer may make another recommendation
based on specific system requirements.
2. Within 10 seconds after pressing the ZONE
button, adjust the volume control to change
the Zone 2 output level. The new setting
appears in the display.
You can control Zone 2 from the front-panel
of the RX-1050 – activate or deactivate Zone
2, change input sources, and adjust the vol-
ume. Controlling Zone 2 from the front-panel
is accomplished by pressing the ZONE but-
ton, which temporarily puts the RX-1050 in Zone
2 control mode, even if the unit is in standby
mode. When the ZONE button is pressed, the
FL DISPLAY shows the current status of ZONE
2 for ten seconds, during which time you can
use the VOLUME control and INPUT SOURCE
buttons to change the ZONE 2 settings. When
ZONE 2 is active, the POWER LED flashes.
When ZONE 2 is off, the POWER LED is
steadily lit.
3. Following 10 seconds with no commands,
the RX-1050 reverts to normal operation.
To configure your system for Zone 2 opera-
tion, connect the left and right Zone 2 outputs
on the RX-1050 to the left and right channel
inputs of the amplifier powering the remote
speakers, using standard RCA audio cables.
Controlling Zone 2 from the
Remote Location
With a properly configured IR repeater sys-
tem, you have full control of Zone 2 using an
RR-939B remote from the Zone 2 location. You
can select and operate a source, adjust the
volume, and turn Zone 2 on or off. Whatever
commands you send from the RR-939B will
change Zone 2 and only Zone 2, just as if
you were controlling a totally independent
audio system in that room. These changes will
have no effect on the main listening room.
NOTE: The Zone 2 outputs provide a VARIABLE
level signal, with control of the volume from
the RX-1050 front-panel and/or remote con-
trol from Zone 2.
ZONE REM IN Jack
NOTE: Zone 2 cannot be controlled from the
remote in the main room.
See Figure 6.
This 3.5 mm mini-jack accepts signals from a
infrared repeater located in Zone 2. A third-
party IR repeater system is required for opera-
tion of the RX-1050’s ZONE 2 functions from
the remote zone.
To turn Zone 2 on or off:
To turn Zone 2 on or off, press the POWER
1. Press the front-panel ZONE button. The
status of Zone 2 appears in the display. If
Zone 2 is in standby, “ZONE OFF” ap-
pears. If Zone 2 is active, “ZONE xxxxx”
showing the current input source appears.
button
on the remote. To adjust the volume
on
in Zone 2, press the VOLUME buttons
the remote. To select a different analog input
source, press one of the INPUT SOURCE but-
NOTE: ZONE 2 and its IR repeater must be in
a different location than RX-1050 to prevent
IR commands intended to control Zone 2 from
inadvertently controlling the main room op-
erations.
tons
on the remote.
2. If Zone 2 is ON, pressing the ZONE but-
ton a second time within 10 seconds turns
it OFF. If Zone 2 is OFF, the second press
of the ZONE button turns it ON with the
last used input source and volume setting.
3. Following 10 seconds with no commands,
the RX-1050 reverts to normal operation.
RX-1050 AM/FM Stereo Receiver
18
Image Response Ratio
65 dB
IR OUT Jacks
Specifications
See Figure 6.
IF Response Ratio
80 dB
The IR OUT 1 & 2 jacks send IR signals re-
ceived at the ZONE REM IN jack or the EX-
TERNAL REM IN jack to an infrared emitter
placed in front of a source component or to
Rotel CD players, cassette decks, or tuners with
a compatible rear panel IR connector.
Audio
AM Suppression Ratio
52 dB
Continuous Amplifier Power
100 watts/channel
(20–20k Hz, <0.05% THD, 8 ohms)
Stereo Separation (100Hz/1 kHz/10 kHz):
40 dB/45 dB/35 dB
Total Harmonic Distortion
<0.05% at rated power
Output level
1.3 V
Intermodulation Distortion (60 Hz:7 kHz)
<0.05% at rated power
Antenna Input
75 ohms unbalanced
This output is used to allow IR signals from Zone
2 to be sent to the source components, or to
pass along IR signals from a remote in the main
room when the sensors on the source compo-
nents are blocked by installation in a cabinet.
See your authorized Rotel dealer for information
on IR repeater systems.
Frequency Response
Line Level: 10 Hz - 70 kHz, 3 dB
Phono: 20 Hz - 20 kHz, 1 dB
AM Tuner
Sensitivity
500 µV/m
Signal to Noise Ratio (IHF “A” weighted)
Line Level: 92 dB
Phono: 74 dB
Selectivity
25 dB
Input Overload
Line Inputs: 5 V
Image Response Ratio
NOTE: The EXT REM IN jack located to the
right of these jacks is for use with an external
IR sensor duplicating the front-panel IR sen-
sor and located in the primary zone. It should
not be used for ZONE 2 IR connections.
Phono Inputs: >120 mV
35 dB
Preamplifier Output Voltage
1.0 V (160 mV Input)
Signal to Noise Ratio
40 dB
Input Sensitivity/Impedance
Line Level: 160 mV/47 kohms
Phono: 2.5 mV/47 kohms
Output level
250 mV
Antenna Input
Tone Controls (Bass/Treble)
Loop Antenna
8 dB at 100 Hz/10 kHz
General
Protection Circuit
Video
Frequency Response
Power Consumption
300 watts
A thermal protection circuit protects the am-
plifier against potential damage in the event
of extreme or faulty operating conditions. Unlike
many designs, the RX-1050’s protection cir-
cuit is independent of the audio signal and
has no impact on sonic performance. Instead,
the protection circuit monitors the temperature
of the output devices and shuts down the am-
plifier if temperatures exceed safe limits.
3 Hz-10 MHz, 3 dB
Power Requirements (AC)
115 volts, 60 Hz (USA version)
230 volts, 50 Hz (European version)
Signal to Noise Ratio
45 dB
Input Impedance
75 ohms
Weight
10.3 Kg/22.7 lb.
Output Impedance
75 ohms
Dimensions (W x H x D)
432 x 121 x 359 mm
17" x 43/4" x 141/8"
Output Level
1 volt
Front Panel Height
(feet removed/for rack mount)
176 mm / 7"
Should a faulty condition arise, the amplifier
will stop playing. If this happens, turn the
amplifier off, let it cool down for several min-
utes, and attempt to identify and correct the
problem. When you turn the amplifier back
on, the protection circuit will automatically reset.
FM Tuner
Usable Sensitivity
14.2 dBf
All specifications are accurate at the time of
printing.
50dB Quieting Sensitivity
20.2 dBf (mono)
45.3 dBf (stereo)
Rotel reserves the right to make improvements
without notice.
Rotel and the Rotel HiFi logo are registered
trademarks of The Rotel Co, Ltd., Tokyo, Japan.
Signal to Noise Ratio (at 65 dBf)
70 dBf (mono)
65 dBf (stereo)
Harmonic Distortion (at 65 dBf)
0.3% (mono)
0.5% (stereo)
Frequency Response
30 Hz-14 kHz, 1.5 dB
Capture Ratio
2.0 dB
Alternate Channel Selectivity
47 dB ( 400 kHz)
Spurious Response Ratio
80 dB
The Rotel Co. Ltd.
10-10 Shinsen-Cho
Shibuya-Ku
Tokyo 150-0045
Japan
Phone: +81 3-5458-5325
Fax: +81 3-5458-5310
Rotel of America
54 Concord Street
North Reading, MA 01864-2699
USA
Phone: +1 978-664-3820
Fax: +1 978-664-4109
Rotel Europe
Meadow Road
Worthing, West Sussex BN11 2RX
England
Phone: +44 (0)1903 524 813
Fax: +44 (0)1903 524 831
Rotel Deutschland
Kleine Heide 12
D-33790 Halle/Westf.
Germany
Phone: +49 05201-87170
Fax: +49 05201-73370
www.rotel.com
082 OM RX-1050 ENG 072701
|