. . . . . . . . . . . . . . . . . . . . . . .
HAWK 2 Family:
. . . . . . . . . . . . . . . . . . . . . . .
(Wide Bus)
. . . . . . . . . . . . . . . . . . . . . . .
ST12400W/WD/WC
. . . . . . . . . . . . . . . . . . . . . . .
ST11900W/WD/WC
. . . . . . . . . . . . . . . . . . . . . . .
Installation Guide
. . . . . . . . . . . . . . . . . . . . . . .
Hawk 2 (Wide bus) Family Install Guide, Rev. C
1
Introduction
Beforeattemptinganyinstallation,pleasereadthrough
all applicable sections of this document, including all
warnings and cautions.
Warning. This equipment generates, uses, and can
radiate radio frequency energy and if not
installed in accordance with these instruc-
tions,maycauseinterferencetoradiocom-
munications.
Electromagnetic interference (EMI) con-
siderations
The drive(s) described herein, as delivered, are de-
signed for system integration and installation into a
suitable enclosure prior to use. As such, the drive(s)
described herein are supplied as a sub-assembly and
arenotsubjecttoSubpartJofPart15oftheFCCRules
and Regulations nor the Radio Interference Regula-
tionsoftheCanadianDepartmentofCommunications.
However, the unit has been tested using proper shield-
ing and grounding and found to be compliant with the
Class A limits of the FCC Rules and the Regulations of
the Canadian Department of Communications.
2
Hawk 2 (Wide bus) Family Install Guide, Rev. C
The physical design characteristics of the drive(s)
described herein, serve to minimize EMI radiation
when installed in an enclosure that provides reason-
able shielding. As such, the drive(s) are capable of
meeting the Class B limits of the FCC Rules and the
RegulationsoftheCanadianDepartmentofCommuni-
cations.
Note. It is the end users' responsibility to assure that
the drive(s) described herein meet the appropri-
ateEMIrequirementsoftheirsystem.ShieldedI/
O cables may be required if the enclosure does
not provide adequate shielding. If I/O cables are
externaltotheenclosure,shieldedcablesshould
be used, with the shields grounded to the enclo-
sure and to the host controller.
Hawk 2 (Wide bus) Family Install Guide, Rev. C
3
Before you begin
Verify that the system is switched off and discon-
nected from main power before any installation is
attempted.
Protect yourself, the drive, and your valuable pro-
grams and data by reading the following cautions
and warnings.
• Do not unpack drive from its static shielded bag until
you are ready to install it in the system.
• Always handle the drive by the frame or casting.
• Do not touch printed circuit board (PCB) or the I/O
connector pins.
• Never apply pressure to the PCB or to the drive top
cover.
• Do not tamper with sealed top cover. Doing so voids
your warranty. The drive contains no user service-
able components. See Product Repair section for
more information.
• Visually inspect the shipping container for any obvi-
ous damage.
4
Hawk 2 (Wide bus) Family Install Guide, Rev. C
• Inspectdriveforpossibleshippingdamage.Allclaims
of this type should be filed promptly with the trans-
porterinvolved.Saveoriginalpackingmaterialstobe
used when reshipping.
• Verifyallpartslistedonshippingbillarereceivedwith
the equipment. Discrepancies or damage should be
reported to the shipping company.
• When transporting or shipping a drive or system,
please ensure that they are correctly packed in
original Seagate approved (or equivalent) container
and shipped via an air-ride carrier experienced in
handling computer equipment.
Caution. The circuit assemblies and components
contained in this equipment can be de-
graded or destroyed by Electrostatic Over-
stress (EOS) or by Electrostatic Discharge
(ESD).
Static electrical charges can accumulate
quickly on personnel, clothing and synthetic
materials. The electrostatic fields due to
these charges when brought in close prox-
imity to susceptible circuit assemblies and
components, can result in degraded reliabil-
ity or immediate failure of the affected com-
ponent or assembly.
Hawk 2 (Wide bus) Family Install Guide, Rev. C
5
To insure optimum reliable equipment op-
eration, it is required that technical support
personneldischargethemselvesbywearing
a grounding strap around the wrist and be
connected to a grounding terminal while
working in the vicinity of, and while handling
EOS/ESD susceptible assemblies/parts. If
unavailable, ground yourself frequently by
touching the metal chassis of the system
before handling any components (this helps
only if the system is connected to a ground).
Avoid static-inducing carpeted areas. This
procedureisespeciallyimportantwhenhan-
dling printed circuit boards (PCBs).
6
Hawk 2 (Wide bus) Family Install Guide, Rev. C
Safety instructions
1. The disc drive(s) are to be installed in a customer
suppliedenclosurewherethesurroundingairdoes
not exceed 50oC.
2. Four (4) 6-32 UNC-2A screws are required for
installation. Maximum screw length into side of
drive is 0.15 inches (3.81 mm). Maximum screw
length into bottom is 0.20 in. (5.08 mm). Maximum
screw tightening torque is 8.0 in-lb (.90 NM) with
minimum thread engagement of .12 in. (3.0 mm).
3. The power requirements are shown in Section 1.0
Product Information.
4. The power supply must satisfy the safety require-
ments for SELV (Safety Extra Low Voltage) cir-
cuits.
5. Service is to be provided by trained Seagate ser-
vice personnel.
6. The incorporation of the disc drives listed in this
guide into a customer enclosure must meet the
appropriate safety requirements of the country in
which it is used (e.g. UL 1950, CAN/CSA-C22.2
No.950-M89,DINVDE0805/05.90andEN60950:
1988 (IEC 950).
Hawk 2 (Wide bus) Family Install Guide, Rev. C
7
Sicherheitsanleitung
1. DäsGerätisteinEinbaugerät,vorgesehenfüreine
maximale Umgebungstemperatur von 50oC.
2. Zur Befestigung der Drive werden 4 Schrauben
benötigt (6-32 UNC-2A). Die maximale Länge der
Schrauben in der unteren Seite des Chassis darf
nicht mehr als 0.20 in (5.08 mm) betragen, die in
der oberen 0.15 in (3.81 mm). Maximalle
Schraubenanziehung von 8.0 in-lb. (.90 NM) mit
minimalen Gewindeansperuch .12 in. (3.00 mm).
3. Die Versorgungsspannungen werden im Kapitel
1.0 (Produkt Information) gezeigt.
4. Die Versorgungsspannung muss SELV entspre-
chen.
5. AlleArbeitendürfennurvonausgebildetemSeagate
Service-Personal durchgefürhrt werden.
6. Der Einbau des Drives muss den Anforderungen
gemässDINVDE0805/05.90oderEN60950:1988
(IEC 950).
8
Hawk 2 (Wide bus) Family Install Guide, Rev. C
Installation Overview
Installation of the drive can be divided into distinct
phases as outlined below. Some of these may not be
applicable to your particular installation requirements.
Refer to the individual drive installation sections for
specific information on your drive model.
• Drive configuration: The user must select which of
thedrivefeaturesareappropriatetoenableforinstal-
lation in their system. This is done by way of the user
configuration jumpers found on the drive PCB.
• Mechanical installation: After setting up the drive
configuration the drive must be mechanically in-
stalled into the host system and the power and I/
O cables attached. Previously mentioned precau-
tions should be observed
• SCSI drives should not be defined in the CMOS:
The SCSI Host adapter has its own BIOS to handle
the Input/output procedures. The CMOS setting for
SCSI drive is either drive type zero, or the "no drive
installed" option.
Hawk 2 (Wide bus) Family Install Guide, Rev. C
9
• Low-level formatting: After the drive has been
properly configured for the system, it does not need
to be low-level formatted, as this has been done by
the factory and does not require this step during
installation. (The low-level format writes the sector
boundariesandtrackinformationtothedrive).Defect
managementinformationisreadfromthedrivebythe
host system when required in the installation proce-
dure. If an installed drive is low-level formatted, all
user data stored on the drive will be lost.
Note. SeagateTechnologyassumes noliability for
lost user data.
• Partitioningandhighlevelformatting:A drivecan
be sub-divided into "partitions" which behave as
individual drives within the system. See your system
documentation. Present day drive installation pro-
grams have menus that lead you through these
installation procedures.
10 Hawk 2 (Wide bus) Family Install Guide, Rev. C
Product repair information
Service requirements
The special facilities required for the manufacture of
these drives generally prohibit repair in the field. If
problemsoccurduringinstallation,pleasecontactyour
supplier for assistance. Do not attempt to disassemble
or repair. Drives should be sent to the repair depot
through the purchase source, if possible. Please ob-
serve the following cautions.
Caution.
• Handle drive with care. Do not drop or bump hard.
• Never remove the cover of these disc drives. Serv-
icing items in the sealed HDA (heads, media, actua-
tor, etc.) require special facilities. The drive contains
no user purchasable parts or PCBs.
• Opening the sealed HDA voids the drive warranty.
• Applyingasolderingdevicetothecomponentsonthe
PCB voids the drive warranty.
Hawk 2 (Wide bus) Family Install Guide, Rev. C 11
• Place drive on a flat, static dissipative surface and
handle with extreme care. Always follow all EOS/
ESD precautions to avoid damage to the electrical
assemblies.
Shipping: When transporting or shipping a drive, a
Seagate approved container must be used. Keep your
original box. They are easily identified by the Seagate
Approved Package label. Shipping a drive in a non-
approved container voids the drive warranty.
Seagate repair centers may refuse receipt of compo-
nents improperly packaged or obviously damaged in
transit. Contact your Authorized Seagate Distributor to
purchaseadditionalboxes.Seagaterecommendsship-
ping by an air-ride carrier experienced in handling
computer equipment.
Product repair and return information
Seagatecustomerservicecentersaretheonlyfacilities
authorized to service Seagate drives. Seagate does
not sanction any third-party repair facilities. Any unau-
thorized repair or tampering with the factory-seal voids
the warranty.
Warranty: Contact your Seagate Authorized Distribu-
tor, Dealer or other purchase source for warranty
information.
12 Hawk 2 (Wide bus) Family Install Guide, Rev. C
If the drive is no longer under warranty contact pur-
chasesourceforrepairinformationorrefertonumbers
listed in the following paragraph .
Technical support services
Please contact your dealer for technical support and
installation troubleshooting. Product Technical Sup-
port is available for all Seagate products by calling the
SeaFAX,SeaFONE,SeaTDDorSeaBOARDservices.
These are toll calls.
SeaFAX: 408/438-2620
You can use a Touch-Tone telephone to access
Seagate's automated FAX delivery system and select
technicalsupportinformationbyreturnFAX. Thisserv-
ice is available 24 hours a day, 7 days a week.
SeaFONE: 408/438-8222
The enhanced phone system provides recorded tech-
nical information on selected Seagate products while
you are on hold. Technical support specialists are
availabletoanswerquestionsfrom8:00AMto5:00PM
PST, Monday through Friday. Recordings are acces-
sible 24 hours a day, 7 days a week.
Hawk 2 (Wide bus) Family Install Guide, Rev. C 13
SeaTDD: 408/438-5382
TDD is a Telecommunication Device for the Deaf
where two people can communicate using a keyboard
that is connected to the phone line. A TDD device is
requiredtoaccessthisservice.Thisserviceisavailable
from8:00AMto5:00PMPST, MondaythroughFriday.
SeaBOARD:
TheSeagateTechnicalSupportBulletinBoardSystem
(BBS) is available 24 hours a day, 7 days a week. A
modemisrequiredtoaccessthisservice. Thecommu-
nications software must be set for eight data bits, no
parity and one stop bit (8N1).
14 Hawk 2 (Wide bus) Family Install Guide, Rev. C
With this service you can access:
• Specifications and jumper configurations for all
Seagate products.
• Reprints of Seagate documentation.
• Adirectoryofinformationandhelpfulutilitiesthatyou
can download to your own computer.
BBS
Modem
Number
Maximum
Baud Rate
9600
9600
2400
Location
United States
England
Germany
Singapore
Australia
408-438-8771
44-62-847-8011
49-89-140-9331
65-227-2217
61-2-756-2359
9600
9600
Note: These are toll calls
Hawk 2 (Wide bus) Family Install Guide, Rev. C 15
Drive specifications
Product
Hawk 2 family (wide)
Information
Interface [7]
ST12400W/WC ST12400WD
SCSI-2 Fast
SCSI-2 Fast
Cache Type
Capacity MB
Unformatted
Formatted [1]
Cylinders
Multi-segmented, 256 Kb*
2537
2148
2621
19
2537
2148
2621
19
Heads
Sectors/track (Avg.)
Recording method
Rev/min
84
RLL (1,7)
5411
84
RLL (1,7)
5411
Seek time (ms typ.) [2]
Average
Read
Write
9.3
10.8
9.3
10.8
Operating environment
Ambient temp. [4]
HDA max temp. [3]
------ 5oC to 50oC-----
-----------60oC----------
Power requirements (Versorgungsspannungen)
+12 V+/-5% (Max [6]
(Max Start) [5]
+5 V +/-5% (Max) [6]
1.0 A
2.4 A
1.0 A
9.0 W
12.1 W
1.0 A
2.4 A
1.2 A
10.8 W
14.6 W
Power Idle
(Typ)
Oper. (Typ)
*Optional 1 MB
16 Hawk 2 (Wide bus) Family Install Guide, Rev. C
Product
Hawk 2 family (wide)
Information
Interface [7]
Fast
ST11900W/WC ST11900WD
SCSI-2 Fast
SCSI-2
Cache Type
Capacity MB
Unformatted
Formatted [1]
Cylinders
Multi-segmented, 256 Kb*
2003
1700
2621
15
2003
1700
2621
15
Heads
Sectors/track (Avg.)
Recording method
Rev/min
84
RLL (1,7)
5411
84
RLL (1,7)
5411
Seek time (ms typ.) [2]
Average
Read
Write
9.3
10.8
9.3
10.8
Operating environment
Ambient temp. [4]
HDA max temp. [3]
------5oC to 50oC------
-----------60oC----------
Power requirements (Versorgungsspannungen)
+12 V+/-5% (Max [6]
(Max Start) [5]
+5 V +/-5% (Max) [6]
Power Idle (Typ)
Oper. (Typ)
1.0 A
2.4 A
1.0 A
9.0 W
12.1 W
1.0 A
2.4 A
1.2 A
10.8 W
14.8 W
*Optional 1 MB
Hawk 2 (Wide bus) Family Install Guide, Rev. C 17
Notes.
[1] Standardunits arefactoryformattedwith512data
bytes per sector. ST12400 OEM standard models
have twelve spare sectors per cylinder and 2
cylinders at inner tracks reserved for spares. The
model ST11900 has six spares per cylinder and 2
spare cylinder per unit.
[2] Does not Include on-board controller overhead.
[3] Maximum measured at any location on top cover.
[4] For best reliability keep below 35oC (95oF).
[5] Adroopofupto-10%ispermissibleforamaximum
of 10 seconds at power up. (abfall von -10% ist
erluabt für 10 Sekunden max).
[6] Measured with an average reading DC ammeter.
Instantaneous +12 V current peaks will exceed
these values.
[7] CanbecommandedtooperateaccordingtoSCSI-
1 protocol.
18 Hawk 2 (Wide bus) Family Install Guide, Rev. C
Initial setup information
For the initial setup connect the cables, set the SCSI
bus address and enable or disable (as required by
system configuration), the SCSI I/O line terminator
resistors (model "W" drives only). Note whether the
drive model number ends in W, WC or WD. These
procedures are described in paragraphs following.
SCSI interface cable connection
The drives covered by this manual are SCSI interface
drives. For "W" and "WD"" models, system connection
is via a 68 pin, SCSI connector. For "WC" models
system connection is via an 80 pin SCSI connector.
Normally "WC" models plug directly into a PCB or
bulkhead mounted mating 80 pin connector. Pin 1 is
noted in Figures 1a and 1b. Some cables have a
contrasting color stripe on one edge to indicate pin 1.
TheI/Oconnectoriskeyedbyvirtueofitsshape. There
is only one way it can mate with the mating input
connector.Strainreliefisrecommendedatthecablefor
drives using cables. Do not block system cooling air
flow in routing of cables.
DC Power connection
Model ST12400W/WD family drives receive DC power
through a 4 pin connector mounted on the PCB next to
the SCSI I/O connector. See Figure 1.
Hawk 2 (Wide bus) Family Install Guide, Rev. C 19
J1
J1-Auxiliary
Pin Power
1P +12V
2P +12V ret
3P + 5V ret
4P + 5V
4P 3P 2P 1P
DC Power
68 Pin SCSI I/O
Connector
Connector
Figure 1. DC power connection, 68 pin SCSI I/O
connector
Model ST12400WC model drives receive power from
the host computer through the 80 pin combined SCSI
I/O and power connector (not shown, since a separate
DC power cable not required). No separate DC power
connector is provided on the drive.
SCSI address selection
On "W" and "WD" model drives, make sure that the
SCSIbusaddressjumperplugsareproperlysetforthe
bus address assigned to the drive. In some systems, a
cableplugsintoeitherJ6orJ1auxiliary, sodriveIDcan
be set at some remote location. See figures 3a and 3b
showingthebusaddressselectheaderandthejumper
configurations that select addresses 0 through 15.
Typically the primary boot device is set to ID 0, and the
subsequent SCSI drives are jumpered in ascending
order. Bus addresses 0 through 14 should be used
(the host adapter probably uses address 15).
20 Hawk 2 (Wide bus) Family Install Guide, Rev. C
If the drive LED shows no on/off activity when the host
is trying to communicate with it, an incorrect bus
address selection at the drive (or remote ID select
location) should be suspected.
On"WC"modeldrivestheSCSIIDcanbeandpresum-
ably will be, set over the 80 pin interface by the host
computer. Unless directed to do so by the system
documentation, no jumpers should be installed for
address selection. On "WC" model drives, the host
system also has complete control over motor start
functions, so no Motor Start or Delayed Motor Start
Jumpers should be installed.
Terminator resistor packs
ModelST12400WfamilydriveshaveI/Olineterminator
resistors that are permanently installed, but can be
enabled or disabled by jumper plug. See jumper in
Figure 3a. If you are installing a single drive, the
terminator resistors must remain enabled. If you are
installingmultipleharddiscdrives,disablethetermina-
tion resistors from all the drives but the one connected
to the end of the SCSI I/O cable.
Hawk 2 (Wide bus) Family Install Guide, Rev. C 21
Model numbers that end in "WD" have differential I/O
circuits and these drives and "WC" mode drives have
no provisions for terminators on the drive PCB. The
system manufacturer must provide some external
means of I/O line termination. The ST12400W/WD
drives can provide power for external terminators if the
TP jumper is installed on the last position on the right
end of J2. See Figure 3a.
Read/Write head auto-park
Seagatediscdrivesdescribedhereinmentionedinthis
drive park the heads automatically at power off. This
feature requires no operator intervention.
Optional parity bit enable
Some systems require parity bit checking. Consult the
system documentation for the specific requirements.
See Figure 3a for location of Parity Bit enable jumper.
Jumper-installed enables parity reporting by the SCSI
bus.
Write precompensation and reduced write
current
NotrequiredonSeagateSCSIInterfacedrivescovered
by this manual.
22 Hawk 2 (Wide bus) Family Install Guide, Rev. C
J1-DC Power
Pin 1P
J1-Auxiliary
Pin 1A
J1 Pin 1
J2
68 Pin
SCSI I/O
Connector
J6
Figure 2a. Hawk 2 family ST12400W/WD model I/O con-
nection 68 pin SCSI I/O and DC power con-
nector). Terminators are not provided.
J2
80 Pin
SCSI I/O
and DC Power
Connector
Pin 1
J6
Figure 2b.Hawk2familyST12400WCmodeldrivephysi-
cal interface (80 pin SCSI I/O and DC power
connector). Terminators are not provided.
Hawk 2 (Wide bus) Family Install Guide, Rev. C 23
Drive configuration
Eachdiscdrivehasoptionselectheaderconnectorson
the back, side and front where jumper plugs are in-
stalled to select the way that the drive is to be config-
ured and to select its ID (0 - 15) on the I/O bus. See
notes following Figure 3b.
ST12400W/WD family 68 pin SCSI I/O drives
OnHawk2family,W/WDmodeldriveseitherJ6(onthe
front of the drive) or J1-auxiliary (at the rear, beside the
DC Power connector) may be used to set the drive ID.
To avoid possible incorrect ID setting, do not use both
J1-auxiliary and J6 for ID selection. The following
figures show where these headers are located on the
different drives covered by this manual. See notes
following Figures 3a and 3b where explanations are
givenaboutthepurposeofeachjumperandspecifythe
standard factory (called "default") settings of these
jumpers (i.e., settings used for most common single
driveapplication).Changestothesesettingsshouldbe
made only if it is known that the system requires a
different configuration.
24 Hawk 2 (Wide bus) Family Install Guide, Rev. C
ST12400WC family 80 pin SCSI I/O drives
On Hawk 2 family, ST12400WC model drives there is
no J1-auxiliary. J6 can be used to set drive ID, but the
host probably does it over the 80 pin interface. J6 may
be used to drive external LED's and connect the syn-
chronized spindle signal to other drives and the host.
This is described in the notes following Figure 3b.
Hawk 2 (Wide bus) Family Install Guide, Rev. C 25
Drive with HDA up, PCB down,
Pin 1
End
SCSI I/O
Connector
viewed from front
Pin 1
HDA
J6
Drive Front
J1-SCSI I/O
J1-Auxiliary
See
Figure
3b
J6
[2]
SCSI ID = 0
SCSI ID = 1
J1-DC Power
Connector
J2
SCSI ID = 2
SCSI ID = 3
SCSI ID = 4
SCSI ID = 5
SCSI ID = 6
SCSI ID = 7
Pin 1
J2
Jumper
Positions
R
E
S
D
S
M
E
W
P
P
E
T
E
T
P
T
P
Reserved
Delay
Motor Start
Enable
Motor Start
[2]
[2]
[3]
SCSI ID = 8
SCSI ID = 9
Write Protect
Parity Option
SCSI ID = 10
SCSI ID = 11
SCSI ID = 12
SCSI ID = 13
SCSI ID = 14
SCSI ID = 15
Enable
Terminators
Term. Power
from Drive
Term. Power
to SCSI Bus
[5]
[5]
[6]
[5]
Term. Power
from SCSI Bus
Position A
A
A
A
A
1 0
3
2
Alternate
Useage:
+5V
11
Ground
5
9
7
3
1
[4]
Connections to drive ID switching
circuits in host equipment
150 Ω 1/8W
Busy
SSP
150 Ω 1/8W
Dashed area is optional user
circuitry external to the drive
Vendor Unique
150 Ω 1/8W
External Fault
Figure 3a. Drive configurator Hawk 2 family
ST12400W/WD model (Wide bus) family
26 Hawk 2 (Wide bus) Family Install Guide, Rev. C
68 Pin SCSI I/O
Connector
J1-Auxiliary
Pin 1A [2]
Drive
HDA
Pin 1
J1-DC Power
4P
3P 2P
1P
J1
PCB
SCSI ID = 0
SCSI ID = 1
SCSI ID = 2
SCSI ID = 3
SCSI ID = 4
SCSI ID = 5
SCSI ID = 6
SCSI ID = 7
[3]
SCSI ID = 8
SCSI ID = 9
SCSI ID = 10
SCSI ID = 11
SCSI ID = 12
SCSI ID = 13
SCSI ID = 14
SCSI ID = 15
A
A
GND
5
A
A
1 0
3
2
Alternate
Useage:
+5V
11 9
7
3
1
[4]
Connections to drive ID switching
circuits in host equipment
150 Ω 1/8W
Busy
SSP
150 Ω 1/8W
Dashed area is optional user
circuitry external to the drive
Vendor Unique
150 Ω 1/8W
External Fault
Figure 3b. Drive configurator Hawk 2 family
ST12400W/WD model (Wide bus) family
Hawk 2 (Wide bus) Family Install Guide, Rev. C 27
Drive with HDA up,
PCB down,
Pin 1
viewed from front
End
Pin 1
HDA
J6
Drive Front
J6
J1
A
A
A
A
1 0
3
2
SCSI ID = 0
SCSI ID = 1
J2
SCSI ID = 2
SCSI ID = 3
SCSI ID = 4
SCSI ID = 5
SCSI ID = 6
SCSI ID = 7
Pin 1
J2
R
E
S
Jumper
Positions
D
S
M
E
W
P
P
E
Reserved
Delay
Motor Start
Enable
Motor Start
[7]
SCSI ID = 8
SCSI ID = 9
Write Protect
Parity Option
Not Used
[7]
SCSI ID = 10
SCSI ID = 11
SCSI ID = 12
SCSI ID = 13
SCSI ID = 14
SCSI ID = 15
Sync Spindle
Remote LED
Not Used
Not Used
Not Used
[8]
Remote LED
CATH
Figure 3c. Drive configurator Hawk 2 family
ST12400WC model (Wide bus) family
28 Hawk 2 (Wide bus) Family Install Guide, Rev. C
Notes for Figure 3a, 3b and 3c:
[1] Notes explaining the functions of the various jumpers
on jumper header connectors J2, J1-auxiliary and J6
are given below in left to right order of jumper position.
The term "default" means as standard OEM units are
configured when shipped from factory. "Off" means no
jumper is installed; "On" means a jumper is installed. Off
or On underlined is factory default condition.
[2] The PCB on "WC" models does not have connector J1-
auxiliary, but has a single 80 pin combined SCSI I/O and
DC power connector instead of the 68 pin SCSI I/O and
4 pin DC power connectors. Included among the 80 pins
are the SCSI ID, Motor Start and Delayed Motor Start
select functions, and the synchronous spindle master
sync signal and the remote LED signals. Do not use J2
and J6 for these five functions if the host uses the ones
included in the 80 pin connector.
[3] Drive ID may be established by installing jumper plugs
in one of the patterns shown in Figures 3a, 3b and 3c,
or by plugging onto J6 or J1-auxiliary a cable that leads
to an external ID selection circuit. Both jumper plugs
and an external ID selection source should not be used.
See [4] for other functions of these two headers that are
time-shared with the drive ID function.
Hawk 2 (Wide bus) Family Install Guide, Rev. C 29
[4] The drive time-shares the ID and LED/SSP functions of
J6 and J1-auxiliary. That is, a cable may be attached to
one of these headers to pick up the synchronized
spindle reference signal (SSP) and three signals that
light external LED indicators. If lines for external ID
selection are not also included in the cable, jumper
plugs must be used on the header not having a cable
connected in order to establish drive ID. The drive reads
the ID from J6 and J1-auxiliary for 250 ms after power-
on or drive reset, and then uses these headers for the
LED and SSP functions the remainder of the time. Host
system documentation should describe the application
of the three LED indicators if it connects a cable to use
this option.
[5] Hawk 2 family model ST12400W and ST11900W only.
[6] Applies to Hawk 2 family ST12400 and ST11900 W and
WD models only.
[7] AppliestoHawk2familyST12400WCandST11900WC
models only.
J2
Jumper.
Position Jumper Function Description
RES
Off/On
Reserved. Default is no jumper installed.
DS ME
Off Off
Spindle starts immediately after power up - De-
fault setting.
30 Hawk 2 (Wide bus) Family Install Guide, Rev. C
continued from previous page
Off On
On Off
Drive spindle does not start until Start Unit com-
mand received from host.
Spindle Startup is delayed by SCSI ID times 12
seconds after power is applied, i.e., drive 0
spindle starts immediately when DC power con-
nected, drive1startsafter12seconddelay, drive
2 starts after 24 second delay, etc.
On On
Drive spindle starts when Start Unit command
received from host. Delayed start feature is over-
ridden and does not apply when ME jumper is
installed.
WP
On
Off
Entire drive is write protected.
Drive is not write protected. Default is no WP
jumper installed.
PE
On
Parity checking and parity error reporting by the
drive is enabled. Default is PE jumper installed.
Drive does not report result of parity checking to
host.
Off
TE
(Applies to "W" models only)
On
With the jumper installed, the optional on-board
(non-removable) terminator circuits are enabled
(connected to the I/O lines). Default is jumper
installed.
Off
Terminator circuits not connected to I/O lines.
Hawk 2 (Wide bus) Family Install Guide, Rev. C 31
continued from previous page
TP TP
Off Off
(Not applicable to "WC" model drives)
No terminator power is connected to drive
terminators or SCSI bus I/O pin 26.
On Off
Off On
Drive supplies its own terminator power only.
Jumper on this position is factory default.
Drive supplies power to I/O pin 26 of SCSI bus;
nonetointernalterminators.Whendriveshave
differential I/O circuits a jumper on the rightTP
position may be needed to power external
terminator (see system documentation). The
Hawk 2 family ST12400WD drive has differen-
tial I/O circuits which have no terminator cir-
cuits on the drive.
On On
Drive supplies terminator power to itself (inter-
nal connection) and to I/O pin 26 of SCSI bus.
This is a legal jumper setting.
TP Position A
On
Off
This horizontally positioned jumper across the
two TP positions nearest PCB edge, connects
terminator power from SCSI bus I/O pin 26 to
thedrive'sinternalterminators(forsingle-ended
I/O only).
See above explanations for TP jumpers.
32 Hawk 2 (Wide bus) Family Install Guide, Rev. C
J6 and J1-Auxiliary
Jumper
Installation Jumper Function Description
A3,A2,A1,A0* Drive ID on SCSI Bus. The drive ID is binary
coded positionwise i.e., jumper in position A3 is
driveID8, inpositionA2 isdriveID4, inposition
A1 is ID 2, position A0 is ID 1 and no jumpers
is ID 0. Default is ID = 0.
Either J1-auxiliary or J6 may be used to select
drive ID. Both should not be used at the same
time, because at some future time when the ID
is changed the user could fail to configure both
J1-auxiliary and J6 the same. Default is ID =
0.
SSP*
No jumper ever installed. Used only as a cable
connection for the reference index signal
(REFIND+) (J6 Pin 6, bottom) for sync spindle
feature. J6 pin 10 is GRD. Installing a jumper
between pins 5 and 6 will cause an erroneous
drive ID indication.
BUSY
Connection for optional external Drive Busy
indicator.
VENDOR Connection for optional indicator for custom
use.
UNIQUE
EXTERNAL Optional indicator indicates some external to
FAULT drive fault occurred.
See host system documentation.
*See notes on page 28 and 29
Hawk 2 (Wide bus) Family Install Guide, Rev. C 33
Drive installation
This section describes the physical mounting of the
drive in the host cabinet and the logical installation as
a system member, which is called drive setup.
Disc drive mounting
Do not touch the connector pins or any PCB compo-
nents without observing static-discharge precautions.
Always handle the drive by the frame only.
The drive may be mounted in any orientation.
• See notes on Figures 4 and 5 pertaining to proper
drive installation.
• Verify that all connections between the drive and the
hostsystemarecorrectlyinstalled.Mostcableshave
acontrastingcolorstripeindicatingpin1.Pin1onthe
drive I/O, J1-auxiliary DC power connectors are
indicated in the figures in the Initial Set-up Informa-
tion section.
• Verify option select and drive ID select jumpers. See
Drive Configuration section.
34 Hawk 2 (Wide bus) Family Install Guide, Rev. C
G
[3]
C
L
[4]
D
[1]
F
E
A
Notes:
[1] Mounting holes three on each side, 6-32
UNC. Max screw length into side of drive
0.15 in. (3.81 mm). Screw tightening
torque 8.0 in-lb (.90 NM) max with minimum
thread engagement of .12 in. (3.00 mm).
[2] Mounting holes four on bottom, 6-32
UNC. Max screw length into bottom of
drive 0.20 in. (5.08 mm). Screw
tightening torque 8.0 in-lb (.90 NM)
max with minimum thread engagement
of .12 in. (3.00 mm).
B
J
[3] Power and interface connections can
extend past the "A" dimension by
0.040 in. (1.02 mm).
[2]
[4] Decorative front panel.
Inches
Millimeters
A
B
C
5.74
4.00
1.620
±
±
+
–
±
±
±
±
±
±
±
±
±
±
0.010 145.80
0.010 101.60
±
±
.25
.25
H
K
0.026
0.021
0.010
0.010
41.15 + .66
–
±
±
±
±
±
±
±
±
±
±
.53
.25
.25
.25
.46
.25
.25
.25
.25
.25
.25
D
E
F
G
H
J
K
L
M
N
P
2.362
.620
4.000
.250
1.750
3.750
2.370
1.725
4.100
0.19
60.00
15.75
0.010 101.60
0.018
0.010
0.010
0.010
0.010
6.35
44.45
95.25
60.20
43.82
P
N
0.010 104.14
0.010 4.83
M
[4]
0.015 max
0.381 max
Figure 4. Hawk 2 family ST12400W/WD model drive
mounting dimensions (68 pin SCSI I/O
connector)
Hawk 2 (Wide bus) Family Install Guide, Rev. C 35
G
[3]
C
L
[4]
D
[1]
F
E
A
Notes:
[1] Mounting holes three on each side, 6-32 UNC.
Max screw length into side of drive 0.15 in.
(3.81 mm). Screw tightening torque 8.0 in-lb
(.90 NM) max with minimum thread engage-
ment of .12 in. (3.00 mm).
R
[5]
[2] Mounting holes four on bottom, 6-32 UNC.
Max screw length into bottom of drive 0.20 in.
(5.08 mm). Screw tightening torque 8.0 in-lb
(.90 NM) max with minimum thread engage-
ment of .12 in. (3.00 mm).
Pin 1
Connector Centerline
B
J
Power and interface connections can extend past
the "A" dimension by 0.040 in. (1.02 mm).
[3]
[4] Decorative front panel.
[5] Connector is centered (side to side) on drive
within ±0.020 in. (.508 mm).
[2]
H
Inches
Millimeters
A
B
C
5.74
4.00
1.620
±
±
+
–
±
±
±
±
±
±
±
±
±
±
0.010 145.80
0.010 101.60
±
±
+
–
±
±
±
±
±
±
±
±
±
±
.25
.25
.66
.53
.25
.25
.25
.46
.25
.25
.25
.25
.25
.25
0.026
0.021
0.010
0.010
41.15
D
E
F
G
H
J
K
L
M
N
P
R
2.362
.620
4.000
.250
1.750
3.750
2.370
1.725
4.100
0.19
60.00
15.75
0.010 101.60
0.018
0.010
0.010
0.010
0.010
6.35
44.45
95.25
60.20
43.82
K
P
N
0.010 104.14
0.010 4.83
0.015 max
0.181
0.381 max
M
[4]
+
–
0.018
0.013
4.597 + .45
–
.33
Figure 5. Hawk 2 family ST12400WC model drive
mounting configuration dimension (80 pin
I/O connector)
36 Hawk 2 (Wide bus) Family Install Guide, Rev. C
Do not power up the host system until the drive is
mounted and the system cover is replaced.
• Connect DC power connector to the drive. (does not
apply to "WC" models)
• Replace the Host System cover.
• Turn on DC power.
• Boot the system from the floppy drive or from a
previously installed hard-drive if there is one.
• Proceed with drive setup of the new hard drive.
Grounding
Signal ground (PCB) and HDA ground are connected
together in the Hawk 2 (Wide bus) drive and cannot be
separated by the user. The equipment in which the
drive is mounted is connected directly to the HDA and
PCB with no electrically isolating shock mounts. If it is
desired for the system chassis to not be connected to
the HDA/PCB ground, the systems integrator or user
must provide a nonconductive (electrically isolating)
method of mounting the drive in the host equipment.
Hawk 2 (Wide bus) Family Install Guide, Rev. C 37
SCSI interface drives
The SCSI interface handles both drive geometry and
defect management internally. The "no drive installed"
option is selected for systems with SCSI drives.
All SCSI interface drives are low-level formatted at the
factory. You may wish to low-level format the drive to
optimize its performance for your system. Consult the
controller documentation for information on low-level
formatting. Partitioning and high-level formatting can
be done through DOS by way of the FDISK utility for
partitioning, and FORMAT for high-level formatting.
Consult your DOS manual for FORMAT and FDISK
command options.
Seagate Technology, Inc.
920 Disc Drive
Scotts Valley, CA. 95066-4544, USA
Publication Number: 77767465, Rev. C
Printed in USA
|