Instruction Manual
46cc/2.8 cu.in. 2-Cycle
GASOLINE CHAIN SAW
Model No.
C944.414460 --- 18 in. Bar
S Safety
S Assembly
S Operation
S Maintenance
S Parts List
WARNING:
Read and follow all Safety Rules and Operating
Instructions before first use of this product.
Sears Canada, Inc., Toronto, Ontario M5B 2B8
530164939
3/12/04
SAFETY RULES
S Do not start cutting until you have a
WARNING: Always disconnect
spark plug wire when making repairs ex-
cept for carburetor adjustments. Be-
cause a chain saw is a high-speed
woodcutting tool, special safety precau-
tions must be observed to reduce risk of
accidents. Careless or improper use of
this tool can cause serious injury.
clear work area, secure footing, and
especially if you are felling a tree, a
retreat path.
OPERATE YOUR SAW SAFELY
S Do not operate with one hand. Seri-
ous injury to the operator, helpers, or
bystanders may result from one-
handed operation. A chain saw is in-
tended for two-handed use.
PLAN AHEAD
S Restrict the use of your saw to adult
users who understand and can fol-
low the safety rules, precautions,
and operating instructions found in
this manual.
S Wear protective gear. Always use
steel-toed safety footwear with non-
slip soles; snug-fitting clothing;
heavy-duty, non-slip gloves; eye pro-
tection such as non-fogging, vented
goggles or face screen; an approved
safety hard hat; and sound barriers
(ear plugs or mufflers) to protect your
hearing. Regular users should have
hearing checked regularly as chain
saw noise can damage hearing.
S Operate the chain saw only in a well-
ventilated outdoor area.
S Do not operate saw from a ladder or
in a tree.
S Make sure the chain will not make
contact with any object while starting
the engine. Never try to start the saw
when the guide bar is in a cut.
S Do not put pressure on the saw, es-
pecially at the end of the cut. Doing
so can cause you to lose control
when the cut is completed.
S Stop engine before setting saw down.
S Hand carry saw only when engine is
stopped. Carry with muffler away
from body; guide bar & chain project-
ing behind you; guide bar preferably
covered with a scabbard.
S Do not operate a chain saw that is
damaged, improperly adjusted, or not
completely and securely assembled.
Always replace bar, chain, hand
guard, chain brake, or other parts im-
mediately if they become damaged,
broken, or are otherwise removed.
Safety Hat
Eye
Protection
Hearing
Protectio
Snug
Fitting
Clothing
Heavy Duty
Gloves
Safety
Shoes
afety Chaps
MAINTAIN YOUR SAW IN GOOD
WORKING ORDER
S Have all chain saw service per-
formed by a qualified service dealer
except the items listed in the MAINTE-
NANCE section of this manual.
S Make certain the saw chain stops
moving when the throttle trigger is
released. For correction, refer to
CARBURETOR ADJUSTMENTS.
S Keep the handles dry, clean, and
free from oil or fuel mixture.
S Secure hair above shoulder length.
Do not wear loose clothing or jewelry;
they can get caught in moving parts.
S Keep all parts of your body away
from the chain when the engine is
running.
S Keep children, bystanders, and ani-
mals at least 30 feet (10 meters)
away from the work area when start-
ing and using the saw.
S Do not handle or operate a chain
saw when you are fatigued, ill, or up-
set, or if you have taken alcohol,
drugs, or medication. You must be in
good physical condition and mentally
alert. If you have any condition that
might be aggravated by strenuous
work, check with doctor before oper-
ating.
S Keep caps and fasteners securely
tightened.
S Nonconforming replacement compo-
nents or the removal of safety devices
may cause damage to the unit and
possible injury to the operator or by-
standers. Use only Craftsman acces-
sories and replacement parts as rec-
ommended. Never modify your saw.
S Maintain chain saw with care.
3
S Keep unit sharp and clean for better
and safer performance.
WARNING: Avoid kickback which
can result in serious injury. Kickback
is the backward, upward or sudden for-
ward motion of the guide bar occurring
when the saw chain near the upper tip
of the guide bar contacts any object
such as a log or branch, or when the
wood closes in and pinches the saw
chain in the cut. Contacting a foreign
object in the wood can also result in
loss of chain saw control.
S Rotational Kickback can occur
when the moving chain contacts an
object at the upper tip of the guide
bar. This contact can cause the
chain to dig into the object, which
stops the chain for an instant. The
result is a lightning fast, reverse
reaction which kicks the guide bar up
and back toward the operator.
S Pinch-Kickback can occur when the
the wood closes in and pinches the
moving saw chain in the cut along
the top of the guide bar and the saw
chain is suddenly stopped. This sud-
den stopping of the chain results in a
reversal of the chain force used to
cut wood and causes the saw to
move in the opposite direction of the
chain rotation. The saw is driven
straight back toward the operator.
S Pull-In can occur when the moving
chain contacts a foreign object in the
wood in the cut along the bottom of
the guide bar and the saw chain is
suddenly stopped. This sudden stop-
ping pulls the saw forward and away
from the operator and could easily
cause the operator to lose control of
the saw.
S Follow instructions for lubricating and
changing accessories.
S Check for damaged parts. Before fur-
ther use of the chain saw, a guard or
other part that is damaged should be
carefully checked to determine that it
will operate properly and perform its
intended function. Check for alignment
of moving parts, binding of moving
parts, breakage of parts, mounting and
any other conditions that may affect its
operation. A guard or other part that is
damaged should be properly repaired
or replaced by a Sears Service Centre
unless otherwise indicated elsewhere
in the instruction manual.
S When not in use, chain saws should
be stored in a dry, high or locked-up
place out of the reach of children.
S When storing saw, use a scabbard or
carrying case.
HANDLE FUEL WITH CAUTION
S Do not smoke while handling fuel or
while operating the saw.
S Eliminate all sources of sparks or
flame in areas where fuel is mixed or
poured.
S Mix and pour fuel in an outdoor area
and use an approved, marked con-
tainer for all fuel purposes. Wipe up
all fuel spills before starting saw.
S Move at least 10 feet (3 meters) from
fueling site before starting.
S Turn the engine off and let saw cool
in a non-combustible area, not on
dry leaves, straw, paper, etc. Slowly
remove fuel cap and refuel unit.
S Store the unit and fuel in a cool, dry
well ventilated space where fuel va-
pors cannot reach sparks or open
flames from water heaters, electric
motors or switches, furnaces, etc.
GUARD AGAINST KICKBACK
Follow all safety rules to help avoid
kickback and other forces which can
result in serious injury.
REDUCE THE CHANCE OF
KICKBACK
S Recognize that kickback can happen.
With a basic understanding of kick-
back, you can reduce the element of
surprise which contributes to acci-
dents.
S Never let the moving chain contact
any object at the tip of the guide bar.
S Keep working area free from obstruc-
tions such as other trees, branches,
rocks, fences, stumps, etc. Eliminate
or avoid any obstruction that your
saw chain could hit while cutting.
S When cutting a branch, do not let the
guide bar contact another branch or
other objects around it.
ack Path
irtions
Cl
W
S Keep saw chain sharp and properly
tensioned. A loose or dull chain can
4
increase the chance of kickback.
Follow manufacturer’s chain sharp-
ening and maintenance instructions.
Check tension at regular intervals,
but never with engine running. Make
sure chain brake nuts are securely
tightened.
S Begin and continue cutting at full
speed. If the chain is moving at a
slower speed, there is greater
chance of kickback occurring.
S Use extreme caution when reenter-
ing a cut.
S Position your left hand on the front
handlebar so it is in a straight line
with your right hand on the rear han-
dle when making bucking cuts.
Stand slightly to the left side of the
saw to keep your body from being in
a direct line with the cutting chain.
S Stand with your weight evenly bal-
anced on both feet.
S Do not overreach. You could be
drawn or thrown off balance and lose
control.
S Do not cut above shoulder height. It
is difficult to maintain control of saw
above shoulder height.
S Do not attempt cuts starting with the
tip of the bar (plunge cuts).
S Watch for shifting logs or other forces
that could close a cut and pinch or
fall into chain.
S Use the specified Reduced-Kickback
Guide Bar and Low-Kickback Chain.
Avoid Pinch-Kickback:
S Be extremely aware of situations or
obstructions that can cause material
to pinch the top of or otherwise stop
the chain.
S Do not cut more than one log at a
time.
S Do not twist saw as bar is withdrawn
from an undercut when bucking.
Avoid Pull-In:
S Always begin cutting with the engine
at full speed and the saw housing
against wood.
S Use wedges made of plastic or
wood. Never use metal to hold the
cut open.
KICKBACK SAFETY FEATURES
WARNING: The following fea-
tures are included on your saw to help
reduce hazard of kickback; however,
such features will not totally eliminate
this danger. Do not rely only on safety
devices. Follow all safety rules to help
avoid kickback and other forces which
can result in serious injury.
S Front Hand Guard: designed to re-
duce the chance of your left hand
contacting the chain if your hand
slips off the front handlebar.
S Position of front and rear handlebars:
designed with distance between han-
dles and “in-line” with each other. The
spread and “in-line” position of the
hands provided by this design work
together to give balance and resis-
tance in controlling the pivot of the
saw back toward the operator if kick-
back occurs.
MAINTAIN CONTROL
Stand to the left of the saw
S Reduced-Kickback Guide Bar: de-
signed with a small radius tip which
reduces the size of the kickback dan-
ger zone. This type bar has been
demonstrated to significantly reduce
the number and seriousness of kick-
backs.
Thumb on
underside
of
Elbow
locked
Small Radius
Tip Guide Bar
Never reverse hand positions
S A good, firm grip on the saw with
both hands will help you maintain
control. Don’t let go. Grip the rear
handle with your right hand whether
you are right or left handed. Wrap the
fingers of your left hand over and
around the front handlebar, and your
left thumb under the front handlebar.
Keep your left arm straight with the
elbow locked.
Large Radius
Tip Guide Bar
S Low-Kickback Chain: has met kick-
back performance requirements when
tested on a representative sample of
chain saws below 3.8 cubic inch dis-
placement.
5
S Tip contact in some cases may cause
a lightning fast reverse REACTION,
kicking guide bar up and back toward
operator.
S Pinching the saw chain along the top
of the guide bar may push the guide
bar rapidly back toward the operator.
S Either of these reactions may cause
you to lose control of the saw which
could result in serious injury. Do not
rely exclusively upon safety devices
built into your saw.
Low-Kickback Chain
Contoured Depth Gauge
Elongated Guard Link
Deflects Kickback
Force And Allows
Wood To Gradually
Ride Into Cutter
CHAIN BRAKE & CKA ANGLE
S Chain Brake: designed to stop the
chain in the event of kickback.
WARNING: WE DO NOT REP-
RESENT AND YOU SHOULD NOT ASSUME
THAT THE CHAIN BRAKE WILL PROTECT
YOU IN THE EVENT OF A KICKBACK. Kick-
back is a lightning fast action whichthrows
the bar and rotating chain back and up to-
ward the operator. Kickback can be
caused by allowing contact of the bar tip in
the danger zone with any hard object.
Kickback can also be caused by pinching
the saw chain along the top of the guide
bar. This action may push the guide bar
rapidly back toward the operator. Either of
these events may cause you to lose con-
trol of the sawwhich could result in serious
injury or even death. DO NOT RELY UPON
ANY OF THE SAFETY DEVICES BUILT INTO
YOUR SAW. YOU SHOULD USE THE SAW
PROPERLY AND CAREFULLY TO AVOID
WARNING: Computed kickback
angle (CKA) listed on your saw and
listed in the CKA table below represents
angle of kickback your bar and chain
combinations will have when tested in
accordance with CSA (Canadian Stan-
dards Association) standards. When
purchasing replacement bar and chain,
considerations should be given to the
lower CKA values. Lower CKA values
represent safer angles to the user, high-
er values indicate more angle and high-
er kick energies. Computed angle repre-
sented indicates total energy and angle
associated without activation of the
chain brake during kickback. In all cases
lower CKA values represent a safer op-
erating environment for the user.
KICKBACK.
Reduced--kickback guide
bars and low--kickback saw chains re-
duce the chance and magnitude of kick-
back and are recommended. Your saw
has a low kickback chain and bar as origi-
nal equipment. Repairs on a chain brake
should be made by an authorized Sears
Service Centre. Take your unitto the place
of purchase or to your nearest Sears Ser-
vice Centre.
The following guide bar and chain com-
binations meet kickback requirements
of CSA Z62.1 and Z62.3 when used on
saws listed in this manual. Use of bar
and chain combinations other than
those listed is not recommended and
may not meet the CKA requirements per
standard.
Computed kickback angle (CKA) Table
BAR
CKA without
chain brake
MODEL
CHAIN P/N
71--3634
P/N
Length
18!
C944.414460
71--36372
24_
SAFETY NOTICE: Exposure to vibra-
tions through prolonged use of gasoline
powered hand tools could cause blood
vessel or nerve damage in the fingers,
hands, and joints of people prone to
circulation disorders or abnormal swell-
ing. Prolonged use in cold weather has
been linked to blood vessel damage in
otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture,
or loss of feeling in the fingers, hands, or
joints, discontinue the use of this tool
and seek medical attention. An anti-vi-
bration system does not guarantee the
avoidance of these problems. Users
who operate power tools on a continual
and regular basis must closely monitor
their physical condition and the condition
of this tool.
SPECIAL NOTICE: Your saw is
equipped with a temperature limiting
muffler and spark arresting screen which
meets the requirements of California
Codes 4442 and 4443. All U.S. forest
land and the states of California, Idaho,
Maine, Minnesota, New Jersey, Oregon,
and Washington require by law that
many internal combustion engines be
equipped with a spark arrestor screen. If
you operate a chain saw in a state or
6
locale where such regulations exist, you
are legally responsible for maintaining
the operating condition of these parts.
Failure to do so is a violation of the law.
Refer to CUSTOMER RESPONSIBILITIES
TABLE in the MAINTENANCE section.
STANDARDS: This saw is listed by
Underwriter’s Laboratories, Inc., in ac-
cordance with:
CSA Z62.1--03 Chain Saws -- Occupa-
tional Health and Safety
CSA Z62.3--96 Chain Saw Kickback
Occupational Health and Safety
ASSEMBLY
If you need assistance or find that parts
are missing or damaged, contact your
Sears Service Centre
WARNING: Before using chain
saw, ensure all fasteners are secure.
CARTON CONTENTS
NOTE: It is normal to hear the fuel filter
rattle in an empty fuel tank.
Check carton contents against the fol-
lowing list.
Your unit has been factory tested and
the carburetor precisely adjusted. As a
result you may smell gasoline or find a
drop of oil/fuel residue on the muffler
when you unpack the unit.
Model C944.414460
S Chain Saw (fully assembled)
S Chain adjustment tool (bar tool)
S 2-cycle engine oil (bar oil not included)
S Carrying case
ASSEMBLY
Your saw is fully assembled; no
assembly is necessary.
Examine parts for damage. Do not use
damaged parts.
OPERATION
KNOW YOUR SAW
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
CHAIN SAW. Compare the illustrations with your unit to familiarize yourself with the
location of the various controls and adjustments. Save this manual for future ref-
erence.
Front Handle
Front Hand Guard
Chain Adjustment Tool
(Bar Tool)
Starter Rope
ON/STOP
Switch
Muffler
Bar Sprocket
Hole
Chain
Bar Oil
Fill Cap
Bumper
Spike
Fuel Mix Fill Cap
Starter Housing
Cylinder Cover
ction
hain
vel
T
T
7
ON/STOP SWITCH
CHAIN BRAKE
The ON/STOP SWITCH is used to stop
the engine.
The CHAIN BRAKE is a device de-
signed to stop the chain if kickback oc-
curs. The chain brake activates auto-
matically in the event of kickback. The
chain brake activates manually if the
front hand guard is pushed forward.
The chain brake is disengaged by pull-
ing the front hand guard back toward
the front handle as far as possible.
THROTTLE TRIGGER
The THROTTLE TRIGGER controls en-
gine speed.
THROTTLE LOCK--OUT
The THROTTLE LOCK--OUT must be
pressed before you can squeeze the
throttle trigger. This feature prevents
you from accidentally squeezing the
trigger.
CHAIN TENSION
It is normal for a new chain to stretch
during first 30 minutes of operation. You
should check your chain tension fre-
quently. See CHAIN TENSION under the
SERVICE AND ADJUSTMENTS section.
CHOKE/FAST IDLE LEVER
The choke and fast idle are set by pull-
ing the CHOKE/FAST IDLE LEVER out
fully for cold or after refueling. The
choke provides additional fuel to the
engine during cold starting.
WARNING: Muffler is very hot
during and after use. Do not touch the
muffler or allow combustible material
such as dry grass or fuel to do so.
BEFORE STARTING ENGINE
line must be mixed with a good quality
synthetic 2-cycle air-cooled engine oil.
We recommend Craftsman brand syn-
thetic oil. Mix gasoline and oil at a ratio
of 40:1. A 40:1 ratio is obtained by mix-
ing 3.2 ounces (95 ml) of oil with 1 gal-
lon (4 litres) of unleaded gasoline. In-
cluded with this saw is a 3.2 ounce (95
ml) container of Craftsman brand oil.
Pour the entire contents of this container
into 1 gallon (4 litres) of gasoline to
achieve the proper fuel mixture. DO NOT
USE automotive oil or marine oil. These
oils will cause engine damage. When
mixing fuel follow the instructions printed
on the container. Once oil is added to
the gasoline, shake container momen-
tarily to assure that the fuel is thoroughly
mixed. Always read and follow the safe-
ty rules relating to fuel before fueling
your unit.
WARNING: Be sure to read the
fuel handling information in the safety
rules section of this manual before you
begin. If you do not understand the
fuel handling information do not at-
tempt to fuel your unit. Seek help from
someone that does understand the in-
formation or contact your Sears Ser-
vice Centre.
GUIDE BAR AND CHAIN OIL
The chain oiler provides continuous
lubrication to the chain and guide bar.
Be sure to fill the bar oil tank when you
fill the fuel tank (Capacity = 6.8 fl. oz.).
Lack of oil will quickly ruin the bar and
chain. Too little oil will cause overheat-
ing shown by smoke coming from the
chain and/or discoloration of the bar.
For maximum guide bar and chain life,
we recommend you use Craftsman
chain saw bar oil. If Craftsman bar oil
is not available, you may use a good
grade SAE 30 oil until you are able to
obtain Craftsman brand. The oil output
is automatically metered during opera-
tion. Your saw will use approximately
one tank of bar oil for every tank of fuel
mix. Always fill the bar oil tank when
you fill the fuel tank.
IMPORTANT
Experience indicates that alcohol
blended fuels (called gasohol or using
ethanol or methanol) can attract mois-
ture which leads to separation and
formation of acids during storage.
Acidic gas can damage the fuel sys-
tem of an engine while in storage.
To avoid engine problems, the fuel
system should be emptied before stor-
age for 30 days or longer. Drain the
gas tank, start the engine and let it run
until the fuel lines and carburetor are
empty. Use fresh fuel next season.
See STORAGE instructions for addition-
al information.
FUELING ENGINE
WARNING: Remove fuel cap
slowly when refueling.
This engine is certified to operate on un-
leaded gasoline. Before operation, gaso-
8
Never use engine or carburetor clean-
er products in the fuel tank or perma-
nent damage may occur.
NOTE: DO NOT cut material with the
choke/fast idle lever at the FULL
CHOKE position.
See the STORAGE section for addition-
al information.
CHAIN BRAKE
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
NOTE: In the following steps, when
the choke/fast idle lever is pulled out to
the full extent, the correct throttle set-
ting for starting is set automatically.
1. Move ON/STOP switch to ON posi-
tion.
2. Pull choke/fast idle lever out to the
full extent.
3. Pull the starter rope quickly with
your right hand a maximum of 10
times.
NOTE: The engine may sound as if it
is trying to start before the 10th pull; if
so, proceed to the next step.
4. Push the choke/fast idle lever in
completely (to the OFF CHOKE
position).
Ensure chain brake is disengaged by
pulling the front hand guard back to-
ward the front handle as far as pos-
sible. The chain brake must be disen-
gaged before cutting with the saw.
WARNING: The chain must not
move when the engine runs at idle
speed. If the chain moves at idle
speed refer to CARBURETOR ADJUST-
MENT within this manual. Avoid con-
tact with the muffler. A hot muffler can
cause serious burns.
STOPPING YOUR ENGINE
S Move ON/STOP switch to the STOP
position.
5. Pull the starter rope quickly with your
right hand until the engine starts.
6. Allow the engine to run for approxi-
mately 5 seconds. Then, squeeze
and release throttle trigger to allow
engine to return to idle speed.
ON/STOP SWITCH
CHOKE/FAST IDLE LEVER
STARTING POSITION
FULL OFF
S To start the engine, hold the saw
firmly on the ground as illustrated.
Make sure the chain is free to turn
without contacting any object.
Starter Rope Handle
STARTING A WARM ENGINE
1. Move ON/STOP switch to ON posi-
tion.
Left Hand
on Front
Handle
2. Pull the choke/fast idle lever out to
the full extent, then push the lever
back in completely (to the OFF
CHOKE position). This will set the
fast idle lock to the start position.
3. Pull the starter rope quickly with
your right hand until the engine
starts.
Right Foot Through Rear Handle
4. Squeeze and release throttle trig-
ger to allow engine to return to idle
speed.
DIFFICULT STARTING (or starting a
flooded engine)
The engine may be flooded if it has not
started after 10 pulls.
Important points to remember
When pulling the starter rope, do not
use the full extent of the rope as this
can cause the rope to break. Do not
let starter rope snap back. Hold the
handle and let the rope rewind slowly.
For cold weather starting, start the unit
at FULL CHOKE; allow the engine to
warm up before squeezing the throttle
trigger.
Flooded engines can be cleared of ex-
cess fuel by following the warm engine
starting procedure listed above. Insure
the ON/STOP switch is in the ON position.
9
Starting could require many pulls de-
pending on how badly the unit is
front handle and use the weight of the
saw to let the tip of the guide bar fall
flooded. If engine still fails to start, refer forward and contact the stump. When
to the TROUBLESHOOTING TABLE or
contact your Sears Service Centre.
the tip of the bar hits the stump, the
brake should activate.
CHAIN BRAKE
OPERATING TIPS
S Check chain tension before first use
and after 1 minute of operation. See
CHAIN TENSION in the MAINTENANCE
section.
S Cut wood only. Do not cut metal,
plastics, masonry, non-wood building
materials, etc.
S Stop the saw if the chain strikes a
foreign object. Inspect the saw and
repair parts as necessary.
S Keep the chain out of dirt and sand.
Even a small amount of dirt will
quickly dull a chain and increase the
possibility of kickback.
S Practice cutting a few small logs us-
ing the following steps. This will help
you get the “feel” of using your saw
before you begin a major sawing op-
eration.
S Squeeze the throttle trigger and al-
low the engine to reach full speed
before cutting.
S Begin cutting with the saw frame
against the log.
S Keep the engine at full speed the
entire time you are cutting.
WARNING: If the brake band is
worn too thin it may break when the chain
brake is triggered. With a broken brake
band, the chain brake will not stop the
chain. The chain brake must be replaced
if any part is worn to less than 0.020 inch
(0.5 mm) thick. Repairs on a chain brake
should be made by your Sears Service
Centre. Take your unit to the place of pur-
chase or to the nearest Sears Service
Centre.
S This saw is equipped with a chain
brake. The brake is designed to stop
the chain if kickback occurs.
S The inertia--activated chain brake is ac-
tivated if the front hand guard is pushed
forward, either manually (by hand) or
automatically (by sudden movement).
S If the brake is already activated, it is dis-
engaged by pulling the front hand guard
back toward the front handle as far as
possible.
S When cutting with the saw, the chain
brake must be disengaged.
Disengaged
d
S Allow the chain to cut for you. Exert
only light downward pressure.
S Release the throttle trigger as soon
as the cut is completed, allowing
the engine to idle. If you run the
saw at full throttle without a cutting
load, unnecessary wear can occur.
S To avoid losing control when cut is
complete, do not put pressure on
saw at end of cut.
Braking function control
CAUTION: The chain brake must be
checked several times daily. The engine
must be running when performing this
procedure. This is the only instance
when the saw should be placed on the
ground with the engine running.
S Stop engine before setting saw down.
TREE FELLING TECHNIQUES
Place the saw on firm ground. Hold the
handles with both hands and apply full
throttle. Activate the chain brake by turn-
ing your left wrist against the hand guard
without releasing your grip around the
front handle. The chain should stop imme-
diately.
WARNING: Check for broken or
dead branches which can fall while
cutting causing serious injury. Do not
cut near buildings or electrical wires if
you do not know the direction of tree
fall, nor cut at night since you will not
be able to see well, nor during bad
weather such as rain, snow, or strong
winds, etc.
Inertia activating function control
WARNING: When performing the
following procedure, the engine must
be turned off.
S Carefully plan your sawing operation
in advance.
S Clear the work area. You need a
clear area all around the tree so you
can have secure footing.
Hold the chain saw approximately 14”
(35 cm) above a stump or other wood-
en surface. Release your grip on the
10
Felling cut here
S The chain saw operator should keep
on the uphill side of the terrain as the
tree is likely to roll or slide downhill
after it is felled.
S Study the natural conditions that can
cause the tree to fall in a particular
direction. These conditions include:
S The wind direction and speed.
S The lean of the tree. The lean of a
tree might not be apparent due to
uneven or sloping terrain. Use a
plumb or level to determine the di-
rection of tree lean.
S Weight and branches on one side.
S Surrounding trees and obstacles.
S Look for decay and rot. If the trunk is
rotted, it can snap and fall toward the
operator.
S Make sure there is enough room for
the tree to fall. Maintain a distance of
2-1/2 tree lengths from the nearest
person or other objects. Engine
noise can drown out a warning call.
S Remove dirt, stones, loose bark,
nails, staples, and wire from the tree
where cuts are to be made.
First cut
Notch
Hinge
Second cut
S After removing the wood, make the
felling cut on the opposite side of the
notch. This is done by making a cut
about two inches higher than the
center of the notch. This will leave
enough uncut wood between the fell-
ing cut and the notch to form a hinge.
This hinge will help prevent the tree
from falling in the wrong direction.
Hinge holds tree on
stump and helps
control fall
Opening of
felling cut
Closing
of notch
NOTE: Before felling cut is complete,
use wedges to open the cut when
necessary to control the direction of
fall. To avoid kickback and chain
damage, use wood or plastic wedges,
but never steel or iron wedges.
Plan a clear retreat path
Direction of Fall
45_
S Be alert to signs that the tree is
ready to fall: cracking sounds, widen-
ing of the felling cut, or movement in
the upper branches.
S As tree starts to fall, stop saw, put it
down, and get away quickly on your
planned retreat path.
S DO NOT use your saw to cut down a
partially fallen tree. Be extremely
cautious with partially fallen trees
that may be poorly supported. When
a tree doesn’t fall completely, set the
saw aside and pull down the tree
with a cable winch, block and tackle,
or tractor.
FELLING LARGE TREES
(6 inches in diameter or larger)
The notch method is used to fell large
trees. A notch is cut on the side of the
tree in the desired direction of fall. After
a felling cut is made on the opposite
side of tree, the tree will tend to fall in
the direction of the notch.
NOTE: If tree has large buttress roots,
remove them before making the notch.
If using saw to remove buttress roots,
keep saw chain from contacting
CUTTING A FALLEN TREE
(BUCKING)
Bucking is the term used for cutting a
fallen tree to the desired log size.
ground to prevent dulling of the chain.
NOTCH CUT AND FELLING TREE
S Make notch cut by cutting the top of
the notch first. Cut through 1/3 of the
diameter of the tree. Next complete
the notch by cutting the bottom. See
illustration. Once the notch is cut, re-
move the wedge of wood from tree.
WARNING: Do not stand on the
log being cut. Any portion can roll
causing loss of footing and control. Do
not stand downhill of the log being cut.
11
First cut on compression side of log
IMPORTANT POINTS
S Cut only one log at a time.
S Cut shattered wood very carefully;
sharp pieces of wood could be flung
toward operator.
S Use a sawhorse to cut small logs.
Never allow another person to hold
the log while cutting and never hold
the log with your leg or foot.
Second
cut
Second cut
S Do not cut in an area where logs,
limbs, and roots are tangled. Drag logs
into a clear area before cutting them.
BUCKING TECHNIQUES
Frst cut ocompression side of log
WARNING: If saw becomes
pinched or hung in a log, don’t try to
force it out. You can lose control of the
saw resulting in injury and/or damage
to the saw. Stop the saw, drive a
wedge of plastic or wood into the cut
until the saw can be removed easily. Re-
start saw and carefully reenter the cut.
Do not use a metal wedge. Do not at-
tempt to restart your saw when it is
pinched or hung in a log.
BUCKING WITHOUT A SUPPORT
S Overcut through 1/3 of the diameter
of the log.
S Roll the log over and finish with a
second overcut.
S Watch for logs with a compresion
side. See illustration for cutting logs
with a compression side.
BUCKING USING A LOG OR
SUPPORT STAND
S Remember your first cut is always on
the compression side of the log. (Re-
fer to the illustration below for your
first and second cut).
Use a wedge to remove pinched saw
S Your first cut should extend 1/3 of the
diameter of the log.
S Finish with your second cut.
Turn saw OFF and use a plastic or
wooden wedge to force cut open.
Using a log for support
Overcutting begins on the top side of
the log with the bottom of the saw
against the log. When overcutting use
light downward pressure.
nd
2
Cut
Overcutting
Undercutting
st
1
Cut
st
1
Cut
Undercutting involves cutting on the
underside of the log with top of saw
against the log. When undercutting
use light upward pressure. Hold saw
firmly and maintain control. The saw
will tend to push back toward you.
nd
2
Cut
WARNING: Never turn saw up-
side down to undercut. The saw can-
not be controlled in this position.
nd
2
Cut
Using a support stand
Always make your first cut on the
compression side of the log. The com-
pression side of the log is where the
pressure of the log’s weight is concen-
trated.
st
1
Cut
12
st
1
Cut
S Start at the base of the felled tree
and work toward the top, cutting
branches and limbs. Remove small
limbs with one cut.
S Keep the tree between you and the
chain.
nd
2
Cut
S Remove larger, supporting branches
with the cutting techniques described
in BUCKING WITHOUT A SUPPORT.
S Always use an overcut to cut small
and freely hanging limbs. Undercut-
ting could cause limbs to fall and
pinch the saw.
LIMBING AND PRUNING
WARNING: Be alert for and
guard against kickback. Do not allow
the moving chain to contact any other
branches or objects at the nose of the
guide bar when limbing or pruning. Al-
lowing such contact can result in seri-
ous injury.
PRUNING
WARNING: Limit pruning to limbs
shoulder height or below. Do not cut if
branches are higher than your shoul-
der. Get a professional to do the job.
S Make your first cut 1/3 of the way
through the bottom of the limb. This
cut will make the limb sag so that it
falls easily on the second cut.
WARNING: Never climb into a
tree to limb or prune. Do not stand on
ladders, platforms, a log, or in any po-
sition which can cause you to lose
your balance or control of the saw.
IMPORTANT POINTS
S Watch out for springpoles.
S Next make a second cut an overcut
all the way through the limb.
Springpoles are small size limbs
which can whip toward you, or pull
you off balance. Use extreme cau-
tion when cutting small size limbs.
S Be alert for springback. Watch out for
branches that are bent or under
pressure. Avoid being struck by the
branch or the saw when the tension
in the wood fibers is released.
S Frequently clear branches out of the
way to avoid tripping over them.
S Finish the pruning operation by using
an overcut so that the stump of the
limb protrudes 1 to 2 inches from the
trunk of the tree.
Second cut
First cut
1/3 of way
LIMBING
S Limb a tree only after it is cut down.
S Leave the larger limbs underneath
the felled tree to support the tree as
you work.
3rd cut 1 to 2 in.
from trunk of tree
13
MAINTENANCE
CUSTOMER RESPONSIBILITIES
WARNING: Disconnect the spark plug before performing maintenance
except for carburetor adjustments.
Fill in dates as you complete
regular service
Before After Every Every
Use Use 5 hrs. 25 hrs.
Service
Dates
Yearly
Check for damaged/worn parts
n
n
n
n
Check for loose fasteners/parts
Check chain tension
Check chain sharpness
Check guide bar
n
n
n
n
Check fuel mixture level
Check guide bar and chain oil
Inspect and clean unit & decals
Check chain brake
n
Clean guide bar groove
Clean air filter
n
n
Clean/inspect muffler and spark
arresting screen
n
Replace spark plug and fuel filter
n
GENERAL RECOMMENDATIONS
The warranty on this unit does not cov-
er items that have been subjected to
operator abuse or negligence. To re-
ceive full value from the warranty, the
operator must maintain unit as instruct-
ed in this manual. Various adjustments
will need to be made periodically to
properly maintain your unit.
S Once a year, replace the spark plug,
air filter element, and check guide bar
and chain for wear. A new spark plug
and air filter element assures proper
air-fuel mixture and helps your engine
run better and last longer.
S Fuel Tank -- Do not use saw if fuel
tank shows signs of damage or leaks.
S Oil Tank -- Do not use saw if oil tank
shows signs of damage or leaks.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Chain Brake Nuts
S Chain
S Muffler
S Cylinder Shield
S Air Filter
S Handle Screws
S Vibration Mounts
S Starter Housing
S Front Hand Guard
CHECK FOR DAMAGED OR
WORN PARTS
CHECK CHAIN TENSION
Contact your Sears Service Centre for
replacement of damaged or worn parts.
NOTE: It is normal for a small amount
of oil to appear under the saw after en-
gine stops. Do not confuse this with a
leaking oil tank.
S ON/STOP Switch -- Ensure ON/STOP
switch functions properly by moving
the switch to the STOP position.
Make sure engine stops; then restart
engine and continue.
WARNING: Wear protective
gloves when handling chain. The
chain is sharp and can cut you even
when it is not moving.
Chain tension is very important.
Chains stretch during use. This is es-
pecially true during the first few times
you use your saw. Always check
chain tension each time you use and
refuel your saw.
14
1. Use the screwdriver end of the
chain adjustment tool (bar tool) to
move chain around guide bar to
ensure kinks do not exist. The
chain should rotate freely.
WARNING: If the saw is operated
with a loose chain, the chain could
jump off the guide bar and result in se-
rious injury.
CHECK CHAIN SHARPNESS
A sharp chain makes wood chips. A
dull chain makes a sawdust powder
and cuts slowly. See CHAIN SHARP-
ENING in the SERVICE AND ADJUST-
MENTS section.
CHECK GUIDE BAR
Conditions which require guide bar
maintenance:
S Saw cuts to one side or at an angle.
S Saw has to be forced through the cut.
S Inadequate supply of oil to bar/chain.
Check the condition of guide bar each
time chain is sharpened. A worn guide
bar will damage the chain and make
cutting difficult.
e
r
Chain Brake
Tool
Nuts
Adjusting
Screw
(Bar Tool)
2. Loosen chain brake nuts until they
are finger tight against the chain
brake.
3. Turn adjusting screw clockwise
until chain solidly contacts bottom
of guide bar rail.
After each use, ensure ON/STOP
switch is in the STOP position, then
clean all sawdust from the guide bar
and sprocket hole.
Adjusting screw
To maintain guide bar:
Chain Brake Nuts
S Move ON/STOP switch to STOP.
S Loosen and remove chain brake
nuts and chain brake. Remove bar
and chain from saw.
4. Using bar tool, roll chain around
guide bar to ensure all links are in
bar groove.
S Clean the oil holes and bar groove
after each 5 hours of operation.
5. Lift up tip of guide bar to check for
sag. Release tip of guide bar, then
1
turn adjusting screw / turn clock-
4
Remove Sawdust From
Guide Bar Groove
wise. Repeat until sag does not
exist.
1
Adjusting Screw --
/
4
Turn
Oil Holes
6. While lifting tip of guide bar, tighten
chain brake nuts securely with the
bar tool.
S Burring of guide bar rails is a normal
process of rail wear. Remove these
burrs with a flat file.
S When rail top is uneven, use a flat file
to restore square edges and sides.
File Rail Edges
and Sides
Square
Worn Groove
Correct Groove
7. Use the screwdriver end of the bar
tool to move chain around guide
bar.
Replace guide bar when the groove is
worn, the guide bar is bent or cracked,
or when excess heating or burring of the
rails occurs. If replacement is necessary,
use only the guide bar specified for your
saw in the repair parts list or on the de-
cal located on the chain saw.
CHECK FUEL MIXTURE LEVEL
S See FUELING ENGINE under the OP-
ERATION section.
8. If chain does not rotate, it is too
tight. Slightly loosen chain brake
nuts and loosen chain by turning
the adjusting screw counterclock-
wise. Retighten chain brake nuts.
9. If chain is too loose, it will sag be-
low the guide bar. DO NOT operate
the saw if the chain is loose.
15
LUBRICATION
INSPECTMUFFLERAND SPARK AR-
RESTING SCREEN
As the unit is used, carbon deposits
build up on the muffler and spark arrest-
ing screen, and must be removed to
avoid creating a fire hazard or affecting
engine performance. Replace the spark
arresting screen if breaks occur.
CLEANING THE SPARK
S See GUIDE BAR AND CHAIN OIL un-
ARRESTING SCREEN
der the OPERATION section.
Clean every 25 hours of operation or
annually, whichever comes first.
INSPECT AND CLEAN UNIT
AND DECALS
S After each use, inspect complete unit
for loose or damaged parts. Clean
the unit and decals using a damp
cloth with a mild detergent.
Steel
Backplate
Muffler
S Wipe off unit with a clean dry cloth.
Muffler
Bolts
CHECK CHAIN BRAKE
S See CHAIN BRAKE in the OPERATION
section.
Aluminum
Backplate
Muffler
Gasket
CLEAN AIR FILTER
A dirty air filter decreases the life and
performance of the engine and in-
creases fuel consumption and harmful
emissions. Always clean your air filter
after 15 tanks of fuel or 5 hours of op-
eration, whichever comes first. Clean
more frequently in dusty conditions. A
used air filter can never be completely
cleaned. It is advisable to replace your
air filter with a new one after every 50
hours of operation, or annually, which-
ever comes first. To clean filter:
1. Loosen and remove 3 screws from
cylinder cover.
Bolt Cover Locknut
1. Loosen and remove the 3 cylinder
cover screws. Remove the cylin-
der cover.
2. Pull off the spark plug boot.
3. Loosen and remove the locknut
from the bolt cover. Remove the
bolt cover.
4. Loosen and remove the 2 muffler
bolts. Remove the muffler, muffler
gasket and backplates. Notice the
orientation of these parts for re-
assembling.
5. Locate the 2 outlet cover screws
on the muffler. Loosen and re-
move both screws. Remove the
outlet cover and spark arresting
screen.
2. Remove cylinder cover.
3. Loosen and remove 2 screws from
air filter.
4. Remove air filter.
5. Clean the air filter using hot soapy
water. Rinse with clean cool water.
Air dry completely before reinstalling.
6. Reinstall air filter and 2 screws.
Tighten screws securely.
BACK VIEW OF MUFFLER
Muffler
Outlet Cover
Screws
7. Reinstall cylinder cover and 3
screws. Tighten screws securely.
Spark Arresting
Screen
Cylinder
Cover
6. Clean the spark arresting screen
with a wire brush. Replace screen
if any wires are broken or screen is
blocked after cleaning.
Screws
7. Reinstall spark arresting screen.
8. Reinstall outlet cover and 2
screws. Ensure outlet cover and
both screws are reinstalled cor-
rectly to prevent damage to the
saw (see illustrations). The ex-
haust outlets must face the chain
brake (bar side) of the saw.
Air Filter
16
5. Replace with Champion CJ--7Y
spark plug and tighten securely
with a 3/4 inch socket wrench.
Spark plug gap should be 0.025
inch.
6. Reinstall the spark plug boot.
7. Reinstall the cylinder cover and 3
screws. Tighten screws securely.
Outlet Cover
Exhaust Outlets
Exhaust Outlets must face
chain brake (bar side) of chain saw
9. Inspect the muffler gasket and re-
place if damaged.
10. Reinstall backplates, muffler gas-
ket and muffler using muffler bolts.
TIghten until secure.
11. Reinstall bolt cover and locknut.
12. Reinstall the spark plug boot.
13. Reinstall the cylinder cover and 3
screws.
Cylinder
Cover
Spark
Plug
Spark
REPLACE SPARK PLUG
Plug
Boot
The spark plug should be replaced
each year to ensure the engine starts
easier and runs better. Ignition timing
is fixed and nonadjustable.
REPLACE FUEL FILTER
To replace the fuel filter, drain your unit
by running it dry of fuel. Remove fuel
cap and its connected retainer from
tank. Pull filter from tank and remove
from line. Replace and reassemble.
1. Loosen 3 screws on cylinder cover.
2. Remove the cylinder cover.
3. Pull off the spark plug boot.
4. Remove spark plug from cylinder
and discard.
SERVICE AND ADJUSTMENTS
See your Sears Service Centre to re-
place and sharpen individual cutters
on your chain.
WARNING: Disconnect the spark
plug before performing maintenance,
service, or adjustments except for car-
buretor adjustments.
TO REPLACE CHAIN:
1. Move ON/STOP switch to the STOP
position.
2. Remove chain brake nuts.
3. Remove chain brake.
4. Remove the old chain.
CHAIN SHARPENING
Chain sharpening requires special
tools. You can purchase sharpening
tools at Sears or go to a professional
chain sharpener.
CHAIN REPLACEMENT
WARNING: Wear protective
gloves when handling chain. The
chain is sharp and can cut you even
when it is not moving.
It is normal for a new chain to stretch
during the first 15 minutes of operation.
You should recheck your chain tension
frequently and adjust the chain tension
as required. See CHAIN TENSION sec-
tion.
Clutch Drum
Chain Brake
Nuts
Replace the old chain when it be-
comes worn or damaged. Use only the
Low-Kickback replacement chain spe-
cified in the repair parts list. The cor-
rect replacement bar and chain is also
specified on a decal located on the
chain saw.
NOTE: An adjusting pin and screw is
used to adjust the tension of the chain. It
is very important that the pin located on
the adjusting screw aligns into the lower
hole in the guide bar. Turning the screw
will move the adjustment pin up and
down the screw.
17
Chain
Brake
ide view of
ain Brake
Adjustment located on Chain Brake
Lower
Hole
5. Turn adjusting screw by hand
counterclockwise until adjusting pin
just touches the stop.
6. Slide guide bar behind clutch drum
until guide bar stops against clutch
drum sprocket.
7. Carefully remove new chain from
package. Hold chain with the drive
links as shown.
Adjusting Pin
Guide Bar
13. Install chain brake nuts and finger
tighten only. Do not tighten any fur-
ther at this point. Proceed to
CHAIN ADJUSTMENT.
CHAIN ADJUSTMENT
See CHAIN TENSION in ASSEMBLY sec-
tion.
CARBURETOR ADJUSTMENT
Tip of
Bar
WARNING: The chain will be
moving during most of this procedure.
Wear your protective equipment and
observe all safety precautions. The
chain must not move at idle speed.
The carburetor has been carefully set
at the factory. Adjustments may be
necessary if you notice any of the fol-
lowing conditions:
CUTTERS MUST FACE IN
DIRECTION OF ROTATION
S Chain moves at idle. See IDLE
SPEED--T adjusting procedure.
S Saw will not idle. See IDLE SPEED--T
adjusting procedure.
Depth Gauge
Cutters
Idle Speed--T
Allow engine to idle. If the chain
moves, idle is too fast. If the engine
stalls, idle is too slow. Adjust speed
until engine runs without chain move-
ment (idle too fast) or stalling (idle too
slow). The idle speed screw is located
in the area above the primer bulb and
is labeled T.
S Turn idle screw (T) clockwise to in-
crease engine speed.
S Turn idle screw (T) counterclockwise
to decrease engine speed.
Drive Links
8. Place chain over and behind
clutch, fitting the drive links in the
clutch drum sprocket.
9. Fit bottom of drive links between
the teeth in the sprocket in the
nose of the guide bar.
10. Fit chain drive links into bar
groove.
11. Pull guide bar forward until chain is
snug in guide bar groove. Ensure
all drive links are in the bar groove.
12. Install chain brake making sure the
adjusting pin in positioned in the
lower hole in the guide bar.
If you require further assistance or are
unsure about performing this proce-
dure, contact your Sears Service
Centre.
18
STORAGE
Fuel stabilizer is an acceptable alter-
WARNING: Perform the following
native in minimizing the formation of
fuel gum deposits during storage. Add
stabilizer to the gasoline in the fuel
tank or fuel storage container. Follow
the mix instructions found on stabilizer
containers. Run engine at least 5 min-
utes after adding stabilizer.
steps after each use:
S Allow the engine to cool, and secure
the unit before storing or transporting.
S Store chain saw and fuel in a well
ventilated area where fuel vapors
cannot reach sparks or open flames
from water heaters, electric motors or
switches, furnaces, etc.
S Store chain saw with all guards in
place and position chain saw so that
any sharp object cannot accidentally
cause injury.
Craftsman 40:1, 2-cycle engine oil (air
cooled) is especially blended with fuel
stabilizer. If you do not use this Sears
oil, you can add a fuel stabilizer to your
fuel tank.
ENGINE
S Store chain saw well out of the reach
of children.
SEASONAL STORAGE
S Remove spark plug and pour 1 tea-
spoon of 40:1, 2-cycle engine oil (air
cooled) through the spark plug open-
ing. Slowly pull the starter rope 8 to
10 times to distribute oil.
Prepare your unit for storage at the
end of the season or if it will not be
used for 30 days or more.
If your chain saw is to be stored for a
period of time:
S Clean saw thoroughly before storage.
S Store in a clean dry area.
S Lightly oil external metal surfaces
and guide bar.
S Replace spark plug with new one of
recommended type and heat range.
S Clean air filter.
S Check entire unit for loose screws,
nuts, and bolts. Replace any dam-
aged, broken, or worn parts.
S At the beginning of the next season,
use only fresh fuel having the proper
gasoline to oil ratio.
S Oil the chain and wrap it in heavy pa-
per or cloth.
FUEL SYSTEM
OTHER
Under FUELING ENGINE in the OPERA-
TION section of this manual, see mes-
sage labeled IMPORTANT regarding
the use of gasohol in your chain saw.
S Do not store gasoline from one sea-
son to another.
S Replace your gasoline can if it starts
to rust.
19
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before perform-
ing all of the recommended remedies below except remedies that require
operation of the unit.
TROUBLE
CAUSE
REMEDY
Engine will not
start or will run
only a few
seconds after
starting.
1. ON/STOP switch in
STOP position.
2. Engine flooded.
1. Move ON/STOP switch to ON.
2. See “Difficult Starting” in the
Operation Section.
3. Fill tank with correct fuel mixture.
4. Install new spark plug.
3. Fuel tank empty.
4. Spark plug not firing.
5. Fuel not reaching
carburetor.
5. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
6. Carburetor requires
adjustment.
7. None of the above.
6. Contact Sears Service (see back cover).
7. Contact Sears Service (see back cover).
1. Idle speed set too high 1. See “Carburetor Adjustment” in the
Engine will
not idle
properly.
or too low.
Service and Adjustments Section.
2. Low Speed Mixture
requires adjustment.
2. Contact Sears Service (see back cover).
3. Crankshaft seals worn. 3. Contact Sears Service (see back cover).
4. Compression low.
5. None of the above.
4. Contact Sears Service (see back cover).
5. Contact Sears Service (see back cover).
1. Air filter dirty.
1. Clean or replace air filter.
2. Clean or replace plug and regap.
3. Contact Sears Service (see back cover).
Engine will not
accelerate,
lacks power,
or dies under
a load.
2. Spark plug fouled.
3. Carburetor requires
adjustment.
4. Exhaust ports or muf-
fler outlets plugged.
5. Compression low.
6. Chain brake engaged.
7. None of the above.
4. Contact Sears Service (see back cover).
5. Contact Sears Service (see back cover).
6. Disengage chain brake.
7. Contact Sears Service (see back cover).
1. Choke partially on.
1. Adjust choke.
Engine
2. Fuel mixture incorrect. 2. Empty fuel tank and refill with
correct fuel mixture.
smokes
excessively.
3. Air filter dirty.
3. Clean or replace air filter.
4. High Speed Mixture
requires adjustment.
5. Crankcase leak.
4. Contact Sears Service (see back cover).
5. Contact Sears Service (see back cover).
1. Fuel mixture incorrect. 1. See “Fueling Engine” in the Operation
section.
Engine runs
hot.
2. Spark plug incorrect.
3. High Speed Mixture
set too lean.
2. Replace with correct plug.
3. Contact Sears Service (see back cover).
4. Exhaust ports or muf-
fler outlets plugged.
5. Carbon build-up on
spark arresting screen.
6. Starter housing dirty
7. None of the above.
4. Contact Sears Service (see back cover).
5. Clean spark arresting screen.
6. Clean starter housing area.
7. Contact Sears Service (see back cover).
20
TROUBLESHOOTING TABLE -- Continued
TROUBLE CAUSE
Oil inadequate 1. Oil tank empty.
REMEDY
1. Fill oil tank.
for bar and
chain
2. Oil pump or oil filter
clogged.
3. Guide bar oil hole
blocked.
2. Contact Sears Service (see back cover).
lubrication.
3. Remove bar and clean.
Chain moves at 1. Idle speed requires
1. See “Carburetor Adjustment” in the
Service and Adjustments Section.
idle speed.
adjustment.
2. Clutch requires repair.
2. Contact Sears Service (see back cover).
1. Chain tension too
tight.
2. Carburetor requires
adjustment.
3. Guide bar rails
pinched.
Chain does not
move when en-
gine is acceler-
ated.
1. See “Check Chain Tension” in the
Maintenance Section.
2. Contact Sears Service (see back cover).
3. Repair or replace.
4. Clutch slipping.
5. Chain brake engaged.
4. Contact Sears Service (see back cover).
5. Disengage chain brake.
Chain clatters
or cuts roughly.
1. Chain tension incorrect. 1. See “Check Chain Tension” in the
Maintenance Section.
2. Cutters damaged.
3. Chain worn.
2. Contact Sears Service (see back cover).
3. Resharpen or replace chain.
4. Cutters dull, improperly 4. See “Chain Sharpening” in the
sharpened, or depth
gauges too high.
5. Sprocket worn.
6. Chain installed
backwards.
Service and Adjustments Section.
5. Contact Sears Service (see back cover).
6. Install chain in right direction.
Chain stops
within the cut.
1. Chain cutter tops not
filed flat.
2. Guide bar burred or
bent; rails uneven.
3. Clutch slipping.
1. See “Chain Sharpening” in the
Service and Adjustments Section.
2. Repair or replace guide bar.
3. Contact Sears Service (see back cover).
Chain cuts at
an angle.
1. Cutters damaged on
one side.
2. Chain dull on one side. 2. See “Chain Sharpening” in the
Service and Adjustments Section.
3. Guide bar bent or worn. 3. Replace guide bar.
1. See “Chain Sharpening” in the
Service and Adjustments Section.
If situations occur which are not covered in this manual, use care and good
judgement. If you need assistance, contact your Sears Service Centre.
21
U. S. EPA / ENVIRONMENT CANADA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OB-
LIGATIONS: The U. S. Environmental
Protection Agency/Environment Cana-
da and Sears Canada, Inc., are
responsibilities, you should contact your
nearest authorized service centre or call
Sears Canada at 1-800-469-4663.
WARRANTY COMMENCEMENT
pleased to explain the emissions the
emissions control system warranty on
your year 2002--2004 small off--road en-
gine. Sears Canada must warrant the
emission control system on your small
off--road engine for the periods of time
listed below provided there has been no
abuse, neglect, or improper mainte-
nance of your small off--road engine.
Your emission control system includes
parts such as the carburetor and the
ignition system. Where a warrantable
condition exits, Sears Canada will repair
your small off--road engine at no cost to
you. Expenses covered under warranty
include diagnosis, parts and labor.
DATE: The warranty period begins on
the date the small off--road engine is
purchased. LENGTH OF COVERAGE:
This warranty shall be for a period of two
years from the initial date of purchase.
WHAT IS COVERED: REPAIR OR RE-
PLACEMENT OF PARTS. Repair or re-
placement of any warranted part will be
performed at no charge to the owner at
an approved Sears Canada servicing
centre. If you have any questions re-
garding your warranty rights and respon-
sibilities, you should contact your near-
est authorized service centre or call
Sears Canada at 1-800-469-4663.
WARRANTY PERIOD: Any warranted
part which is not scheduled for replace-
ment as required maintenance, or which
is scheduled only for regular inspection
MANUFACTURER’S WARRANTY
COVERAGE: If any emissions related
part on your engine (as listed under
Emissions Control Warranty Parts List) is to the effect of “repair or replace as nec-
defective or a defect in the materials or
workmanship of the engine causes the
failure of such an emission related part,
the part will be repaired or replaced by
Sears Canada. OWNER’S WARRAN-
TY RESPONSIBILITIES: As the small
off--road engine owner, you are respon-
sible for the performance of the required
maintenance listed in your instruction
manual. Sears Canada recommends
that you retain all receipts covering
maintenance on your small off--road en-
gine, but Sears Canada cannot deny
warranty solely for the lack of receipts or
for your failure to ensure the perfor-
mance of all scheduled maintenance.
As the small off--road engine owner, you
should be aware that Sears Canada
may deny you warranty coverage if your
small off--road engine or a part of it has
failed due to abuse, neglect, improper
maintenance, unapproved modifications,
or the use of parts not made or ap-
proved by the original equipment
essary” shall be warranted for 2 years.
Any warranted part which is scheduled
for replacement as required mainte-
nance shall be warranted for the period
of time up to the first scheduled replace-
ment point for that part. DIAGNOSIS:
The owner shall not be charged for
diagnostic labor which leads to the de-
termination that a warranted part is de-
fective if the diagnostic work is per-
formed at an approved Sears Canada
servicing centre. CONSEQUENTIAL
DAMAGES: Sears Canada may be li-
able for damages to other engine com-
ponents caused by the failure of a war-
ranted part still under warranty. WHAT IS
NOT COVERED: All failures caused by
abuse, neglect, or improper mainte-
nance are not covered. ADD--ON OR
MODIFIED PARTS: The use of add--on
or modified parts can be grounds for dis-
allowing a warranty claim. Sears Cana-
da is not liable to cover failures of war-
ranted parts caused by the use of
manufacturer. You are responsible for
presenting your small off--road engine to
a Sears Canada authorized repair
centre as soon as a problem exists.
Warranty repairs should be completed in
a reasonable amount of time, not to ex-
ceed 30 days. If you have any ques-
tions regarding your warranty rights and
add--on or modified parts. HOW TO
FILE A CLAIM: If you have any ques-
tions regarding your warranty rights and
responsibilities, you should contact your
nearest authorized service centre or call
Sears Canada at 1-800-469-4663.
WHERE TO GET WARRANTY SER-
VICE: Warranty services or repairs shall
22
be provided at all Sears Canada service
centres. Call 1-800-469-4663. MAINTE-
NANCE, REPLACEMENT AND RE-
PAIR OF EMISSION RELATED
PARTS: Any Sears Canada approved
replacement part used in the perfor-
mance of any warranty maintenance or
repair on emission related parts will be
provided without charge to the owner if
the part is under warranty. EMISSION
CONTROL WARRANTY PARTS LIST:
Carburetor, Ignition System: Spark Plug
(covered up to maintenance schedule),
Ignition Module. MAINTENANCE
STATEMENT: The owner is responsible
for the performance of all required main-
tenance as defined in the instruction
manual.
The information on the product label indicates which standard your engine is certified.
Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA.
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
23
|