TABLE OF CONTENTS
Operation Manual
NIGHTWITNESS NIGHT VISION MONOCULAR
Unit Designation…..............……….............2
Components….................….....……..….....3
Technical Specifications…........................4
Precautions…..........................……............7
Unit Stracture…....………………..…...........8
Functions and
Indicators...................................................12
Operation Instructions.………...….…….14
Warranty….............…….………………......22
Customer Support…................................24
Acceptance certificate.............................25
In USA: 2331 Superior Ave. Cleveland, OH 44114
In Canada: 105 SparksAve., Toronto, ON M2H 2S5
TECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS (con’t)
SPECIFICATIONS:
SPECIFICATIONS:
EYEPIECE
Focal Length
Eye relief
Exit pupil dia
20 ìì
16 ìì
7 ìì
Magnification:
Field of View : 5 õ
5 ± 0,3 õ; 1,25 ± 0,1 õ
Diopter adjustment
+4, -4 dpt
10,5°
40°
3 ì to Infinity
1,25 õ
ELECTRICAL
Power supply
Focusing Range:
1 AA Ni-MH rechargeable cell 1.2V (not less 2300 mAh)
or 1 AA alkaline cell 1.5 V
IMAGEINTENSIFIERTUBE
Type
Photocathode sensitivity
integral
18 ìì, Gen II+ Extra Definition. 18 ìì, Gen III GaAs
Continuous operation time (20°Ñ)
10 h (observation)
5 h (with IR illumination)
5mW
:
350 - 600 uA/lm
18 - 40 mA/W
500 - 1600 uA/lm
70 - 120 mA/W
36 - 64 lp/mm
IR LED illuminator ( at λ= 850 nm)
spectral( at λ= 850 nm),
Resolution
MECHANICAL
Dimensions (L õ W õ H)
Weight
Gain
18 000 - 25 000
150õ47õ70 ìì ( 1,25 õ); 220õ60õ70 ìì ( 5 õ )
400 ã ( 1,25 õ); 550 ã ( 5 õ )
1/4"-20 TPI
LENS
Lens mount
Standard
C-mount, 1”-32 TPI
100 ìì/F1.7; 25 ìì/F1.3
The whole line of 1” C-mount lenses including zoom, tele & wide-angle
SLR camera lenses using corresponding adapters(e.g. Canon EOS & Nikon AF to C-mount)
Tripod thread
Interchangable
ENVIRONMENTAL
Operational temperature
Storage temperature
Humidity
- 20°Ñ … +40°Ñ
- 30°Ñ … +50°Ñ
98%
5
4
PRECAUTIONS
TECHNICAL SPECIFICATIONS (CONT)
Nightwitness is a sophisticated precise optical instrument equipped with electronics.
Therefore, it should be handled with due care.
Warning
!
Image Intensifier possible defects table.
•Try to avoid strong heat, direct sunlight, impacts, dust, moisture and sudden changes of
temperatures. Keep it in mind that, although being very durable, Nightwitness contains fragile
Clarity of Image Intensifier tube is check against the table below:
components.
•Do not touch the optical surfaces with fingers. Doing so may damage the antireflection coating.
•Cleaning of optical surfaces should only be performed with professional camera lens cleaning
ADMITTED TOTAL
RE EFE S, M
FIELD OF VIEW CLEANNESS:
2
CIRCULAR ZONE
supplies.
A
A
OF
D
C
T
M
ZONE
DIMENTIONS, MM
ADMITTED
NUMBER
•Use only a soft clean cloth to clean the exterior of the device.
•Do not take the cover off the lens if not necessary.
NEGLECTED
DIAMETER, MM
QUALITY
•Keep away from heating appliances and central heating.
•Make sure to switch off the unit and remove the battery during periods of non-operation
1
2
3
0...9,0
9,0...14,5
14,4...18,0
0,06
0,08
0,1
0,15
0,25
0,35
1
2
2
0,12
0,27
0,45
and when storing the device for long period of time.
•Do not apply unnecessary pressure to the lens assembly, agile elements & thread connections.
•Due to considerable optical magnification of the eyepiece some small structures inside the tube
coating in the form of dark and/or white points may be seen in the field of view which does not
affect the serviceability of the device.
6
7
UNIT STRUCTURE
UNIT STRUCTURE (con’t)
Operation switches as well as the battery compartment and a place for wrist strap for NVD are
located on the back surface of the unit .
Ocular of NVD
Nightwitness has
a
high quality wide angle ocular with magnification of 12,5 õ.
Moisture collector cartridge is located of the left side of the body of NVD.
The standard tripod socket 1/4" is located on the right side of the NVD.
The dioptric correction is -4...+4 dtp, as well long eye relief allows for user who wear glasses to use
the unit with out removing them. Ocular is supplied with rubber eye guard which allows for proper and
steady position of the eye, witch is very important especially when the unit is used on a moving platform
(i.e. Boat, plane, vehicle). The rubber Eye piece can rotate 360° to allow for proper functionality with
either right or left eye. The ocular is design as video recording or interchangable adapter to allow for
Photo-, Video- and CCTV-camera.
OVERVIEW
The night vision device (NVD) Nightwitness is observational opto-electronic monocular, intended for
examining objects and orientation at night or under dark conditions. The unit utilizes a generation
2+XT or 3 image intensifier tube, which amplifies available moonlight, starlight or man-made light. The
device was designed to be easy to use and provide many years of operation.
HIGH-LIGHT CUT OFF CIRCUIT
Some of the typical activities where Nightwitness can be useful:
•
•
•
•
•
Law enforcement
Nightwitness is provided with a unique high-light cut off circuit to protect image intensifier tube.
‘Intellectual’ TTL sensor measures a luminance level directly on the photocathode surface. If it
exceeds the overload capacity for an Image Intensifier used in the device– blue LED in a field of
view warns an operator that after 5 – 7 seconds power supply of the device will be switched off.
When the luminance goes down below that level – the Image Intensifier power supply recovers
automatically. So the operator has plenty of time to protect the device from bright light sources and
at the same time not to lose the sight of an object to be controlled
Security
Search and rescue
Hunting
Photography (dark room operation) or with camera adaptable feature
8
9
UNIT STRUCTURE (con’t)
UNIT STRUCTURE (con’t)
LOW BATTERYAND IR “ON” INDICATORS
Unit “ON” indicator (green color), Low battery indicator “Low Battery” (red light), IR indicator “IR
ON” (yellow color) & high light cut off indicator “Bright Light” (blue color) located in the top portion of
visible field of view of the NVD.
POWER SOURCE
Power source for NVD is provided by one Ni-MH power cell voltage 1.2V (not less 2300 mAh) type
«ÀÀ» or one Alkaline battery voltage 1.5V type «ÀÀ».
IR Illuminator
This is enough for continued operation for up to 20 hours at 20°Ñ in observation mode and 6 hour of
operation with IR illuminator turned on. The batteries are easy to replace in any environment and the
construction of battery house is designed so the even if polarities are reversed the unit is protected.
NVD is equipped with build in IR light for illumination of close by objects located in front portion of the
body of module. Brightness of the IR light is bright enough to read the map in complete darkness (with
objective lens 25mm/F1.3) it is also allows to conduct small repairs and maintenance work.
Moisture collector
Besides normal operation the NVD is able to use external power supply from any external source
with voltage of 3.5 - 1.5V, as an example the NVD work of a car adapters or CCTV-systems. In order to
use external power source in the battery compartment instead of «ÀÀ» battery you need to instal
external power adapter (optional), which ensures that voltage is stabilized at 1.5V, as well as it protects
from reverse polarities and a transition cycle in the chain of external source range to ± 60V. Adapter is
equipment with low voltage slot type size 5,5/2,1 for continuous power supply.
Moisture collector is design to collect moisture inside the NVD during operation. If Moisture collector
is dry the color inside the window is blue. If on the other hand, moisture collector is full of moisture than
the color is pale pink or grey. You can replace Moisture collector cartridge using the key provided with the
unit.
Soft padded carrying case
Carrying case is design to accommodate the unit as well as all accessories that are included in the
standard package . The case is made from nylon with soft padded inserts designed to absorb the shock
of impact as well additional packets for other tools. The case also has adjustable shoulder strap.
10
11
FUNCTIONS AND INDICATORS
FUNCTIONS AND INDICATORS
• I/R illuminator
Infrared ON indicator
(yellow)
Low Battery Indicator
(red)
Strap holder
•
•
•
•
Battery House
cover
•
Tripod Thread 1/4" •
• Focusing Ring
Power ON indicator
(green)
IR fixed security
switch
•
Objective lens
Main body of Nightwiness
•
Power ON/OFF •
switch
•
High Light cut off indicator
(blue)
Dioptrict adjustment ring
•
Eye piece
Desiccant
•
12
13
OPERATION INSTRUCTIONS
OPERATION INSTRUCTIONS (con’t)
Precautions
•
Adjust the ocular to your eye sight,
rotating the dioptric adjustment ring .
Never disassemble the unit by yourself.
There are no wires or modules that requires user to clean or modify.
•
Point the unit towards the object of
Operation procedures
your surveillance.
•
•
Twist off the battery house cap.
⇒
NEVER DIRECT THE LENS IN
THE DIRECTION OF BRIGHT LIGHT
Insert one battery type «ÀÀ» 1.5V, make sure that polarity
is correct..
•
For maximum performance focus in on
your object by rotating the focusing ring on
the objective lens.
•
•
•
Screw the battery cap back on.
Take the unit into your hand. Put on the wrist wrap.
Take the protective cover off the objective lens.
• For IR operation: depress fixated button IR illuminator , keeping the button depressed move it in to
IR “ON” position. At this stage the Yellow light indicator light will come on the top portion of the ocular.
⇒
NEVER OPERATE YOUR NIGHT VISION DEVICE IN DAYLIGHT WITH-
OUT THE LENS COVER ON
• After the operation make sure that the unit is turned OFF, by moving the switch to OFF position on
•
Turn ON the unit, by moving the position of the switch to (ON).
the unit.
The Green Indicator light will come on and will be visible at the top portion of the ocular
•
Close the objective cover.
14
15
OPERATION INSTRUCTIONS (con’t)
OPERATION INSTRUCTIONS (con’t)
USE OF ACCESSORIES
Wrist wrap
LOW BATTERY INDICATOR
Low battery indicator is RED and is located in ocular field of view, the
indicator will start to blink if voltage of the power supply is between 0.9 - 1.0
V, in this case the Green unit ON indicator is off. If the voltage is very low
(less than 0.9V), all indicators of NVD will automatically turn off. Turn OFF the
unit and replace the battery.
•
Insert the end of the wrist wrap in the hole located on the back
of the unit.
•
Tighten the wrist wrap by passing is through hinge, as it is
shown on the picture in the right.
INDICATOR HIGH-LIGHT CUT OFF
Mounting the unit on a tripod
High-light indicator is blue color and is located in the ocular field of view,
this indicator light will blink if the unit is exposed to bright light source that can
damage the unit. If the unit is exposed continuously for more than 5 - 7s, the
unit will turn OFF and the indicator light will glow continuously. At low light
levels below normal parameters High-Light indicator will turn off, and the unit is
operational again automatically. Should you require to operate the unit in high
light situations cover the objective lens with protective cap.
•
Align tripod screw with tripod thread 1/4"
located on the right hand side of the body of the
unit.
•
•
Tighten the tripod screw.
Place the tripod on a stable ground and fully
extend the legs of a tripod.
16
17
OPERATION INSTRUCTIONS (con’t))
OPERATION INSTRUCTIONS (con’t)
Operation with Photo cameras, Video Cameras and CCTV-Systems
Using the unit with external power supply of car adapter
•
•
•
Remove the ocular from the unit by unscrewing it from the body of the unit.
Install instead of the ocular, proper photo-video or CCTV-adapter.
Connect the NVD with an adapter to photo-,
• Remove battery house cover.
• Remove the battery «ÀÀ» and insert a external power adapt-
er (optional). Lock the cap of an adapter into place.
video- or CCTV - camera (further referred to as cam-
era) with reference to instruction related to specific
adapter.
• Connect the power source to slot of external power supply
cable( or car adapter ) with a standard low voltage plug type 5,5/
2,1.
•
If required place the unit along with the cam-
era on a tripod.
• Connect second end of the cable to external power source,
make sure that polarities are correct or connect the cable to ciga-
rette lighter slot.
•
•
Turn on the unit and the camera.
Focus the unit with the help of focusing ring
on a adapter or camera.
•
•
Point the NVD with the camera on the object of your choice.
• Turn ON the unit.
Establish maximum resolution of the image by focusing the objective ring located on the objective
lens of the unit.
•
At this stage you can take photos or make a video at night.
18
19
OPERATION INSTRUCTIONS (con’t)
OPERATION INSTRUCTIONS (con’t)
Environmental Conditions
•
The capacity of the battery in low temperature is decreased. If possible the batteries should
always be protected from low temperatures.
Nightwitness functions equally reliable in normal as well as extreme weather conditions.
Although the unit performs reliably in harsh weather conditions and high moistures it is expected that
user will do due diligence and pay more close attention to operation instructions, in order to keep unit
in good working order and prevent early demise of the unit.
High temperature operation
•
•
Unit functions properly at temperatures up to +40°C.
Low temperature operation
If possible please make sure that battery is protected from high heat and direct sun light.
Operation in high moisture environments
•
Unit functions properly at temperatures below -20°C. In low temperatures the objective focus-
ing ring as well as dioptric correction ring may become more stiff. Do not force the adjustment rings
as they may become nonoperating.
In the areas of high moisture the optical surfaces of the unit should always be clean and dry.
•
The unit should never be subjected to extreme weather fluctuations. If it is required to move
the unit from one extreme environment to other, the unit should be placed in waterproof container and
closed it tight etc... The container should not be opened until it reaches same temperature as the new
environment, if this is not performed the unit will have moisture condensation on optical surfaces.
Moisture on surfaces of the unit can be discarded with clean dry cloth.
Optical surfaces should be cleaned with special optical cloth.
20
21
Moisture collector cap replacement
WARRANTY
Replacing the moisture cap
NEWCON OPTIK warrants this product against defects in material and workmanship for
one year from the date of the original date of consumer’s purchase, but no more than 18 months
from the date of manufacturing. Longer warranty periods are available, subject to the terms of
specific sales contract. Should your Newcon product prove defective during this period, please
bring the product securely packaged in its original container or an equivalent, along with proof
of the date of original purchase, to your Newcon Dealer. Newcon will repair (or at its option
replace with the same or comparable model), the product or part thereof, which, on inspection
Moisture cap should be replaced in a clean dry place. New Moisture cap can be exposed for no
more than 1-2 minutes.
The following is required for replacement of cartridge:
•
•
Prepare spare cartridge supplied with your unit;
With supplied key unscrew the moisture collector
by Newcon, is found to be defective in materials or workmanship.
cartridge that is full of moisture from the NVD and immediately
replace it with a new cartridge;
What This Warranty Does Not Cover:
• Screw in the replacement cartridge until rubber O-ring is
NEWCON is not responsible for warranty service should the product fail to be properly
maintained or fail to function properly as a result of misuse, abuse, improper installation, neglect,
damage caused by disasters such as fire, flood, lightning, improper electrical current, or service
other than by a NEWCON Authorized Service. Postage, insurance, or shipping costs incurred in
presenting your NEWCON product for warranty service are your responsibility. Please include a
cheque or money order made out to NEWCON OPTIK for the amount of $15.00 to cover shipping
visibly deformed.
• In order to restore moisture filled cartridge it is required to unscrew the cap of Moisture collector
cartridge with the key provided, empty the silica gel into clean metallic container and place the
container in the heat source (i.e. electric stove, camping stove etc.)
and handling within North America
Silica gel can never be directly exposed to fire. To restore silica gel the temperature should be
between 150 to 170°Ñ. Silica gel will dry with in 3 to 4 hours.
22
23
CUSTOMER SUPPORT
ACCEPTANCE CERTIFICATE FOR NIGHTWITNESS
Image Intensifier Tube
Should you experience any difficulties with your Newcon OPTIK product, consult
the enclosed manual. If the problem remains unresolved, contact our customer
support department at (416) 663-6963 or Toll free at 1-877-368-6666. Our
operating hours are 9am-5pm, Monday - Friday, Eastern Standard Time.
Minimum
30
Measured
Resolution, lines/mm
Photocathode sensitivity,
integral, µA/ lm
400
Light amplification
20,000
At no time should the equipment be sent back to Newcon without
following the instructions of our technical support department.
Newcon accepts no responsibility for unauthorized returns.
Image Intensifier Tube Serial Number: ____________
Date of production: __________
Quality Inspector signature: ____________
To locate NEWCON Authorized Dealer call:
The unit with the serial Number___________
Tel: (416) 663-6963 Fax: (416) 663-9065
corresponds to all technical specifications and has passed the inspection.
The defective products should be shipped to:
Date of production: _____________
From USA only: 2331 Superior Ave. Cleveland, OH 44114
Quality Inspector signature: __________________________
Quality assurance seal
From all other countries: 105 Sparks Ave., Toronto, ON M2H 2S5, CANADA
24
25
|