CR-2200 SERIES
CASH DRAWER
USER’S MANUAL
FCC Notes:
Rev. A0
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions manual, may cause interference
to radio communications. It has been tested and found to comply with limits for a Class
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever
measures to correct the interference.
Warranty Limits:
Warranty terminates automatically when any person other than the authorized
technicians opens the machine. The user should consult his/her dealer for the problem
happened. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.
About This Manual:
Posiflex has made every effort for the accuracy of the content in this manual. However,
Posiflex will assume no liability for any technical inaccuracies or editorial or other
errors or omissions contained herein, nor for direct, indirect, incidental, consequential
or otherwise damages, including without limitation loss of data or profits, resulting
from the furnishing, performance, or use of this material.
This information is provided “as is” and Posiflex Technologies, Inc. expressly
disclaims any warranties, expressed, implied or statutory, including without limitation
implied warranties of merchantability or fitness for particular purpose, good title and
against infringement.
The information in this manual contains only essential hardware concerns for general
user and is subject to change without notice. Posiflex reserves the right to alter product
designs, layouts or drivers without notification. The system integrator shall provide
applicative notices and arrangement for special options utilizing this product. The user
may find the most up to date information of the hardware from web sites:
All data should be backed-up prior to the installation of any drive unit or storage
peripheral. Posiflex will not be responsible for any loss of data resulting from the use,
disuse or misuse of this or any other Posiflex product.
All rights are strictly reserved. No part of this documentation may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, or otherwise, without prior express written consent from
Posiflex Technologies, Inc. the publisher of this documentation.
© Copyright Posiflex Technologies, Inc. 2007
All brand and product names and trademarks are the property of their respective holders.
Part 1
P/N: 19230900030
CARTON CONTENTS
1. Cash drawer pre-assembled.
2. User’s manual.
3. Separators of coin compartment: 5 pcs.
4. Key 2pcs: There is a key serial No. sticker on the cash drawer bottom
side. If user lost the key he/she can order the key according to this
number.
5. Signal Cable depend on model
a). For CR-2200: The standard signal cable is 21863018010 which has a 8
pin modular plug at one end to connect to the cash drawer and a 6 pin
modular plug at the other end to connect to the POS system/printer.
This cable serves for most popularly used POS equipment such as
Posiflex POS terminals, all Posiflex POS printers, most Epson POS
printers, most Star POS printers and all other compatibles. The user
may cut the 6 pin end or order the ready cut cable CCBLA-180A and
assemble this free end according to his POS printer specification if the
POS printer used applies different connection. The cable connection on.
CCBLA-180A is as below:
RJ45 Function
Wire color
Red
Blue
Green
Yellow
Pin 1 Drawer open sense
Pin 2 Drawer open sense return
Pin 7 + 24V to solenoid
Pin 8 Drawer kick pulse
b). For CR-2204: Serial signal RS232 DF9F RJ9 conversion cable
(21863259900/21863159900).
c). For CR-2205: USB cable (21863250800/21863150800)
6. Power Source depend on model
a). For CR-2200: not applicable
b). For CR-2204: Power adapter 12VAC 1.5A
c). For CR-2205: Power adapter 12VAC 1.5A
Part 3
INSTALLATION
Coin compartment adjust:
Open the top cover and remove any protective materials such as a
piece of PE foam if it exists.
The coin compartment separator can be removed from and inserted
till click into the grooves in adjustable coin compartment zones for appropriate
compartment size.
Coin Compartment Separator
Adjustable Coin Compartment
CR-2200:
1). Connect the 8 pin plug of CR cable to cash drawer and the 6 pin plug to
CR port of POS system or POS printer as shown below:
Rear View
8P modular Jack
Output to drawer
CR Cable: 21863018010
Cash Drawer
With Printer Interface
Connect to POS System or
Printer 6P modular Jack
2). Turn the keylock to standby position.
CR-2204:
1). Connect the 4 pin RJ9 plug of RS232 conversion cable to the RJ9 jack
at the rear side of CR-2204 and connect the DB 9 pin connector to
RS232 port of host (PC or POS) system as shown in drawing below.
2). Check the specification of power adaptor on its nameplate. Insert the
Part 4
power adaptor into the correct power outlet. Insert the output plug to
the power jack at rear side of CR-2204 to supply power for drawer
kickout.
3). Turn the keylock to standby position.
4). Set the communication protocol of the RS232 port in host system to
use baud rate of either 9600 bps or 19200 bps.
Rear View
RJ9 (4P4C) modular Jack
USB Type B Connector
AC 12V I/P
Connect to Adaptor
USB Cable:
RS232 Conversion Cable:
(21863150800/21863250800)
(21863159900/21863259900)
Connect to RS232 port of host system
(For CR-2204 only)
Connect to USB Port of host
system (For CR-2205 only)
CASH DRAWER With RS232 & USB Interface
CR-2205:
1). The drawer number (PID) is default to be 7. Refer to the guidance for
“Jumper Setting Change” below if the PID has to be changed.
2). Connect USB type B connector (more or less square one) of USB
cable to the USB connector at rear side of CR-2205 and the type A
connector end to USB port of host (PC or POS) system as shown in
drawing above.
3). Check the specification of power adaptor on its nameplate. Insert the
power adaptor into the correct power outlet. Insert the output plug to
the power jack at rear side of CR-2205 to supply power for drawer
kickout.
4). Turn the keylock to standby position.
5). Install the USB utility driver from Posiflex Product Information CD
with Posiflex POS system or visit our web sites
or
or
Switch Setting Change for CR-2204/2205:
1). Use key to open the cash drawer. Take out the removable tray and you
Part 5
can find a control board in the bottom. The lay out of the control
board is illustrated below.
4
3
2
1
JP1
O
N
2). By switch setting at different positions of JP1, interface selection
between RS232 and USB and PID selection can be made.
a. Interface select: switch position 1 of JP1 defines interface of the cash
drawer besides the interface cable used. When switch position 1 is
ON, the controller responds to RS232 signals. When switch position 1
is OFF, the cash drawer works to USB interface.
b. USB PID select: Switch positions 2, 3 or 4 define a drawer number
for the cash drawer as in below table so that this cash drawer is going
to respond accordingly in USB communication. Please note that
within each system there should never be any 2 USB interface cash
drawers carrying the same drawer number.
USB PID
1
2
3
4
5
6
7
0
JP1 SW
2
3
4
ON
ON
ON OFF OFF OFF OFF ON
ON OFF OFF ON
OFF ON OFF ON OFF ON OFF ON
ON OFF OFF ON
Default setting: Drawer 7 (SW2: OFF; SW3: OFF; SW4: OFF)
UPOS and WEPOS driver application:
Please first find in Posiflex Product Information CDROM or
download from Posiflex web sites for UPOS driver setup. In this application
CR-2204 responds to OpenDrawer command only; CR-2200/2204 are
compliant to UPOS version 1.7 and CR-2205 is compliant to UPOS version
1.8 and is also WEPOS certified.
Part 6
FUNCTIONAL TEST
CR-2200
1. Follow the printer’s manual of the printer the cash drawer is connected to
open cash drawer.
2. If the cash drawer is connected to a Posiflex POS system, follow the
technical instruction of the system to open the cash drawer.
CR-2204
1. Under DOS prompt, type “MODE COM1 9600 N 8 1”. Hit the ENTER
key.
2. Type “TYPE CON>COM1”. Hit the ENTER key.
3. Type “CTRL-G” (Press Ctrl and G keys together). Hit the ENTER key,
then the drawer will open and pass the test.
4. Hit CTRL-C (Press Ctrl and C keys together) to return the computer back
to the normal display mode.
In case the cash drawer is connected to serial port other than COM1 please
substitute COM1 above to proper port name.
CR-2205
1. Please find in Posiflex Product Information CDROM or go to Posiflex
the Posiflex Product Information CDROM that comes with any Posiflex
POS system, please go to folder “\Drivers\CR\USB” and click
“SETUP.EXE” to install the USB Cash Drawer Test Program.
2. Start up the test program and click “STATUS” button. The drawer status
of Open/Close or Not present will be displayed under each drawer
number as “O”, “C” or “N”
3. Use a key to turn the lock to standby position (the one marked with sign
at middle), click the check only the box(es) under the drawer number(s)
for the drawer(s) to be tested then click the “KICK” button.
4. The cash drawer will then open and the Open/Close/Not present status of
the tested drawer number will be renewed accordingly. If these status are
correct, the USB interface cash drawer passes the test
Part 7
SPECIFICATIONS
MECHANICAL: Dimensions:
460 (W) x 174.9 (D) x 101.5 (H) mm
18.2” (W) x 6.9” (D) x 4.0” (H)
Weight: 4.2 Kg
Removable tray with a lock-on cover (option)
ELECTRICAL:
Power Source
Solenoid Drive (for CR-2200)
Pulse Amplitude
Pulse Width
12 to 24 VDC
100 to 250 msec
10% max.
Pulse Duty Cycle
Max. Current Consumption 0.75A @ 12 VDC / 1A @ 24 VDC
AC Adaptor (for CR-2204/2205)
Input Voltage
120 VAC ± 10 % / 240 VAC ± 10 %
@50 -60 Hz
Output Voltage
12 VAC at 1.5 A
Interface
Direct Drive: CR-2200
Serial (RS232C)
CR-2204
9600; 19200
none
Baud rate
Parity
Data Bits
Stop Bits
8
1
USB (1.1): CR-2205
Security Code
CR-2205
USB PID
Drawer Open Sense
CR-2200
CR-2204
CR-2205
Drawer open sense circuit shorts when drawer open
Pin 9 in DB9 connector goes high when drawer open
Through USB driver
Part 8
KEYLOCK OPERATION
Lock ( ): Physically lock the drawer.
Open ( ): Open the drawer by the key. At this position
the key can’t be extracted and will be automatically
springed away once released.
Standby ( ): Automatically open the drawer by POS printer
or POS system or interface signal control
Keylock
STRUCTURE
Check Slot
Inside CR- 2200/ 2204/ 2205
Adjustable Bill
compartment
Adjustable coin
compartment
Cash Tray
Fixed coin compartment
Check Storage
Part 9
T31454
警告使用者
這是甲類的資訊產品，在居住的環
境中使用時，可能會造成射頻干
擾，在這種情況下，使用者會被要
求採取某些適當的對策。
Part 10
|