Profoto Pro 8a Generator PRO 8A 1200 AIR User Manual

Pro-8a 2400 Air  
Pro-8a 1200 Air  
User´s Guide  
thank you for choosing Profoto  
ThanksforshowingusyourconfidencebyinvestinginaPro-8a  
generator. For more than three decades we have sought the  
perfectlight.Whatpushesusisourconvictionthatwecanoffer  
even yet better tools for the most demanding photographers.  
Before our products are shipped we have them pass an  
extensive and strict testing program. We check that each  
individual product comply with specified performance,quality  
and safety. For this reason our flash equipment is widely used  
inrentalstudiosinParis,London,NewYork,andTokyoandalso  
themost rented flashall over theworld.  
3
Somephotographerscan tell justfromseeinga picture,  
ifProfotoequipmenthas been used  
Professionalphotographersaroundtheworldhavecometovalue  
Profoto’s expertise in lighting and light-shaping. Our extensive  
range of Light Shaping Tools offers photographers unlimited  
possibilitiesforcreatingandadjustingtheirownlight.  
Everysinglereflectorandaccessorycreatesitsspeciallightand  
theuniqueProfotofocusingsystemoffersyouthepossibilityto  
createyourownlight with onlya few different reflectors.  
EnjoyyourProfoto product!  
Safety instructions  
SAfety PrecAUtionS!  
Donotoperatetheequipmentbeforestudyingtheinstructionmanualandtheaccompanyingsafety.Make  
surethatProfotoSafetyInstructionsisalwaysaccompaniedtheequipment!Profotoproductsareintended  
for professional use! Generator, lamp heads and accessories are only intended for indoor photographic  
use. Do not place or use the equipment where it can be exposed to moisture, extreme electromagnetic  
fields or in areas with flammable gases or dust! Do not expose the equipment to dripping or splashing.  
Do not place any objects filled with liquids, such as vases, on or near the equipment. Do not expose the  
equipment to hasty temperature changes in humid conditions as this could lead to condensation water  
in the unit.Do not connect this equipment to flash equipment from other brands.Do not use flash heads  
without supplied protective glass covers or protective grids. Glass covers shall be changed if it has  
become visibly damaged to such an extent that their effectiveness is impaired, for example by cracks  
or deep scratches. Lamps shall be changed if they are damaged or thermally deformed.When placing  
a lamp into the holder ensure not to touch the bulb with bare hands. Equipment must only be serviced,  
modified or repaired by authorized and competent service personnel! Warning -The terminals marked  
with theflash symbolarehazardous live.  
4
WArninG – electrical Shock – High Voltage!  
Mains powered generator shall always be connected to a mains socket outlet with a protective earthing  
connection! Only use Profoto extension cables! Do not open or disassemble generator or lamp head!  
Equipment operates with high voltage.Generator capacitors are electrically charged for a considerable  
time after being turned off. Do not touch modeling lamp or flash tube when mounting umbrella metal  
shaftinitsreflectorhole.Disconnectlampheadcablebetweengeneratorandlampheadwhenchanging  
modeling lamp or flash tube! The mains plug or appliance coupler is used as disconnect device. The  
disconnect device shall remain readily operable. Batteries (battery pack or batteries installed) shall not  
beexposed toexcessive heatsuchassunshine,fireorthelike.  
caution – Burn Hazard – Hot Parts!  
Do not touch hot parts with bare fingers! Modeling lamps, flash tubes and certain metal parts emit  
strong heat when used! Do not point modeling lamps or flash tubes too close to persons.All lamps may  
on rare occasions explode and throw out hot particles! Make sure that rated voltage for modeling lamp  
correspondswith technical dataofuserguideregardingpowersupply!  
notice equipment overheating risk  
Removetransportcapfromlampheadbeforeuse!Donotobstructventilationbyplacingfilters,diffusing  
materials,etc.over inlets and outlets of the equipment ventilation or directly over glass cover,modeling  
lampor flash tube!  
note about rf!  
This equipment makes use of the radio spectrum and emits radio frequency energy.Proper care should  
betakenwhenthedeviceisintegratedinsystems.Makesurethatallspecificationswithinthisdocument  
arefollowed,especiallythoseconcerningoperatingtemperatureandsupplyvoltagerange.Makesurethe  
device is operated according to local regulations.The frequency spectrum this device is using is shared  
with otherusers.Interferencecan notberuled out.  
final Disposal  
Equipment contains electrical and electronic components that could be harmful to the environment.  
EquipmentmaybereturnedtoProfotodistributorsfreeofchargeforrecyclingaccordingtoWEEE.Follow  
local legal requirements for separate disposal of waste, for instance WEEE directive for electrical and  
electronicequipmenton theEuropean market,when productlifehasended!  
table of contents  
System description ...................................................................................................6  
Profoto Air ...................................................................................................6  
Profoto Air Remote (optional accessory).......................................................6  
Profoto Air Sync (optional accessory) ...........................................................6  
Profoto Air USB (optional accessory) ............................................................6  
Lamp Heads  
......................................................................................................7  
ProHead ......................................................................................................7  
ProTwin ......................................................................................................7  
ProRing ......................................................................................................7  
ProRing 2 ...................................................................................................8  
5
Functionality  
......................................................................................................8  
Power supply...............................................................................................8  
Energy control .............................................................................................8  
Modeling light..............................................................................................9  
Sync signaling.............................................................................................9  
Ready signaling.........................................................................................10  
Speed control ............................................................................................10  
Ready lamp/Test function ..........................................................................11  
Flash before ready.....................................................................................11  
Fan Cooling & Protection System ...............................................................11  
Additional information.............................................................................................12  
Color Temperature .....................................................................................12  
f-stop Stability & Range.............................................................................12  
Flash Duration ...........................................................................................12  
Petrol-Electric Generators..........................................................................13  
Operating instructions.............................................................................................13  
Lamp head connection ..............................................................................13  
Power connection......................................................................................13  
Settings ....................................................................................................14  
Sync via cable ...........................................................................................14  
Sync via Photocell / IR-slave......................................................................14  
Sync via radio (Profoto Air).........................................................................14  
Wireless remote control.............................................................................15  
Turn off generator......................................................................................15  
Technical data Profoto Pro-8a 2400 Air...................................................................16  
Technical data Profoto Pro-8a 1200 Air...................................................................18  
Nomenclature ....................................................................................................20  
Quick Guide  
....................................................................................................21  
System description  
Pro-8a is designed to be free of compromises. Pro-8a is the fastest, roughest, most  
versatile and stable generator yet still with the widest power range we ever developed.  
Pro-8ahasanewuniquetwostageSMPS(SwitchModePowerSupply)rechargingcircuit  
makingrepetitionratesfasterthaneverbefore.Shootupto20framespersecondor2per  
secondat1200Ws.Usageofcamerascontinuestriggeringisnowpracticallypossiblewith  
Pro-8a.DurabilityofPro-8aisexceptionaltocomplywithrentalandfashionneedsplusthe  
greatly increasedneed offrames taken due to no cost of fi lm with digital cameras.  
Due to our invention,Profoto PiPE technology (Pre-ignition Plasma Establishing – patent  
pending). Pro-8a has an extensive wide light power range with exceptional stability of  
the light energy and color temperature. Safety of the Pro-8a generator is exeptional and  
complieswiththehighestdemands.  
6
Profoto Air  
Pro-8a is already equipped with the Profoto Air transceiver to prepare for convenient  
wirelesssyncandremotecontrol.ProfotoAirsystemisoperatingononeofeightselectable  
radio channelsonthe2.4 GHzradiofrequencyband for world wideuse.  
Profoto Airremote(optional accessory)  
Complete generator control and sync at your camera or in your hand, including flash  
energy and modeling light control.Control practically an infinite number of generators in  
up to six groups,eitherallatonceinMastermode,orinindividual groups.  
Profoto AirSync(optional accessory)  
Allowssynchronizingofapracticallyaninfinitenumberofgenerators,withthesamehigh  
performanceasProfotoAirRemote.  
Profoto AirUSB (optionalaccessory)  
An USB 2.0 offers wireless connection of your flash generators to the Profoto StudioAir,a  
softwarerunningonyourPCorMacthatgivesyoufullcontrolofyourstudioflashsystem.  
The interface can also be used for updates, extended optional functions and  
customizations.  
notice  
When Pro-8a is remote controlled from a computer, the setting of the four controls (SYNC, MODEL, READY  
and SPEED) may be overruled by the Profoto Studio 2 program.  
If any of the controls is computer overruled it will be indicated by four red LCD:s on the  
generatorcontrolpanel.  
For moredetailedinformation,please refer to theProfotoStudio 2 User’s Guide.  
Lamp Heads  
Pro-8aisdesignedforallofthepresentstate-of-the-artProheadsandlightshapingtools.For  
selectedpreviousmodelsofProfotoslampheadswereisasimpleupdateforcompatible  
fancoolingat100–120V markets.  
ProHead  
The standard heavy-duty flash lamp head is the Profoto ProHead, built for producing  
flasheswithPro-8a,upto2400Wsoverandoveragain,hourafterhour.Ithasanintegrated  
high efficient, long life halogen model-pilot lamp with a switch and a fuse. A thermally  
controlled 2-speed efficient fan provide silent cooling. For safety reasons thermal  
protectionisbuilt-in.  
7
Theflashtubeandhalogenlampareprotectedbyadiffusingglasscoveralsoservingasa  
light source corresponding filter and color correction filter.Optional glass cover versions  
areavailable.TheoptimizedflashtubeismadebyhighgradeUV-freefilteredquartsglass  
and heavy dutyelectrodestomaximizelifetime.  
Protwin  
Whendemandsareeventougher,theProfotoProTwinisavailablewithtwoflashtubesthat  
effectively double the performance. Used with a single generator, it can produce shorter  
flashdurationsbysplittinghalfofthepowertotwoflashtubes.UsedwithtwoPro-8a2400  
Air,it can half therecycling speedordoublethelight energy,up to 4800Ws.  
Powered from one of the two connected cables ProTwin has an integrated high efficient  
halogen model-pilot lamp with a switch and a fuse. A thermally controlled 2-speed  
efficient fan provides silent cooling.For safety reasons thermal protection is built-in.The  
flashtubeandhalogenlampareprotectedbyadiffusingglasscoveralsoservingasalight  
source corresponding filter and color correction filter. Optional glass cover versions are  
available.  
The optimized flash tube is made by high grade UV-free filtered quarts glass and heavy  
dutyelectrodestomaximizelifetime.  
Proring  
If you look for a more lightweight ring flash without modeling light, there’s the Profoto  
ProRing, with the capacity of up to four 2400 Ws flashes per minute.An entirely mobile  
sourceoflight,theringflashfitsallPro-7generators.Theadjustabletripodmountbracket  
and the wide interior (100 mm diameter) makes the ProRing compatible with all types of  
cameras as well as most lenses. Optional accessory reflectors expand the ring flash’s  
capabilitiesfurther.  
Proring 2  
For fashion or macro photography, when you want a direct and very prominent light, the  
ProfotoProRing2providesaringflashcapableofunlimitedflashrepetitionrateduetobuilt-in  
thermallycontrolledsilentandefficientfancooling.Theoptimizedflashtubeismadebyhigh  
gradeUV-freefilteredquarts glassand heavy duty electrodesto maximizelifetime.  
A powerful 200Whalogen modeling light arebuilt-inwith switch and fuse.  
functionality  
8
Powersupply  
ThePro-8ageneratorcanbeconnectedto100–120VACor200–240VAC,50–60Hz.The  
powersupplyfusemustnotbesmallerthanspecifiedinthetechnicaldata.Thegenerator  
automaticallysensesandadapts to thevoltageand frequencysupplied.  
WArninG  
Neveruseordinaryhouseholdextensioncordstoelongatethepowercable.Theymayoverheat.Alwaysunwindcord  
reelextensionwinders fully beforeuse.ContactyourProfotodealerforproperequipment.  
Due to the two stage SMPS (Switch Mode Power Supply) technology, the Pro-8a could  
make a hearable sound during the recharge cycle.This is fully normal and could be seen  
asthe signofpowerbeingcharged into thegenerator.  
energy control  
The selected energy levels for channel A and B are shown in Flash Light Energy Display  
A [6]and B[17].  
The f-stop scale reading is default. To show energy in Ws scale, push and hold the Ws  
Switch [1].  
In f-stop scale, the maximal energy (100%) is shown as 10.0. In Ws scale, the maximal  
energy (100%)is2400forPro-8a2400Air and 1200 for Pro-8a1200Air.  
The maximal energy for channelA is 10.0 (100%) and the maximal energy for channel B  
9.0(50%).The maximal energyin totalfor thetwo channels is 100%.  
FlashLightEnergyControlA[8]andControlB[19]areusedtoadjusttheenergylevelsfor  
channelA and B respectively:  
Turnthecontrolclockwisetoincreasetheenergyin1/10f-stopincrementsandcounter-  
clockwise todecrease.  
• Press and hold down the control (abeepwill sound) and turn the control clockwise to  
increase theenergyin1f-stopincrements and counter-clockwise to decrease.  
Modeling light  
The Modeling Light Switch [9] is used to turn on/off the modeling light for channelA and  
B simultaneously. When the modeling light is on, the Modeling Light Switch knob [9] is  
illuminated.  
The ModelingLightControl [7]is usedto select one of fourmodeling light alternatives:  
• PROP: The modeling light intensity for each lamp head is automatically adjusted to  
correspondinproportionin-betweenthegenerators set energyand maximalenergy.  
•½PROP:ThemodelinglightintensityisadjustedautomaticallyinproportionasforPROP  
whentheenergylevelischanged,butwithhalfmodelinglightintensityofthedesignated  
energy. Half proportional modeling light is used when generators of different sizes are  
usedtogether; Pro-8a1200Air shall beset to ½ PROP and Pro-8a2400AirtoPROP.  
9
MAX:Themodelinglampgetsthemaximalintensity,regardlessoftheflashlightenergy  
settings.  
MAXPROP:Maximalproportionalmodelinglightisusedwhenmaximallightisneededon  
onechannel(theonewithhighestenergylevel).Thehighestsetchannelwillgetmaximal  
intensity and the other will correspond proportionally.Therefore the modeling light may  
changeon achannelwhichisnot adjusted.  
IfProStudio2isusedtocontrolthegenerators,aSmartPropfunctionisavailable.Itissimilar  
totheMAXPROPsetting,buttheintensityproportionsmatchalllampsandgenerators.  
Syncsignaling  
The Pro-8a generator can be synchronized with the camera in different ways; via cable,  
via Photocell / IR-slave or via the ProfotoAir radio system (LPA radio system available on  
special order).Bothsystemscan not be integrated inthesame generator.  
• The two Sync Connectors [2] allow the camera and a flash meter to be connected  
simultaneously.The5metersynccablecanwithoutrestrictionsbeelongatedwithasync  
extension cable.The bidirectional optical isolated Profoto sync interconnection cable is  
recommendedtobeusedtopreventgroundreferenceinterferencewhenconnectingsync  
cables betweendifferentgenerators.  
ThePhotocell/IR-slave[3]sensesignalsfrommostIRsynctransmittersaswellasfrom  
otherflash lightasaSlaveandsynchronizetheunit.  
• The Profoto Air remote radio control system is integrated in all Pro-8a generators,  
meaning that the generators are prepared to be synchronized or controlled either viaAir  
Remote,Air Sync orviatheProfotoStudio2computer programandAir USB.  
The Sync Control[5]isusedtocontrolthesync signaling:  
• RADIO:The generatorisset to sync viaradio.  
• SET:Enablessettingofradiochannel and group.  
• OFF:The generatorissettosync viacable.  
• SLAVE:The generatorisset to sync viaphotocell / IR.  
ready signaling  
Readysignalingisusedtoindicatewhenthegeneratoris100%fullycharged.TheReady  
Control [16]isusedtoselectone of fourreadysignaling alternatives:  
• OFF: No ready signal. This setting also disables the sound indicating that a switch is  
pressed or a control isturned.  
• DIM: The modeling light will be turned off when the generator is being charged, and  
turned on again when the charging is completed. This setting also disables the sound  
indicating thataswitch ispressed ora controlis turned.  
10  
• BEEP: A clear ”beep” will sound to indicate that the charging of the generator is  
completed. This setting also enables the sound indicating that a switch is pressed or a  
control isturned.  
BEEP-DIM:Themodelinglightwillbeturnedoffwhenthegeneratorisbeingcharged,and  
turnedonagainwhenthechargingiscompleted.Aclearbeep”willalsosoundtoindicate  
thatthechargingiscompleted.Thissettingalsoenablesthesoundindicatingthataswitch  
is pressed oracontrol isturned.  
Speedcontrol  
The versatile recycling speed settings make it possible to efficiently utilize the mains  
powersupplybyadjustingandoptimizingthemaximumpossiblespeedandloadwithout  
blowingfuses.Thegenerator’samperageloadfromthemainspowersupplycorresponds  
proportionally tothespeed setting.  
The SpeedControl [18]isusedto select one of fourrecycling speed settings:  
• 25% The slow recycling speed is four times as long as the MAX recycling speed.This  
alternative shall be selected when the generator is connected to a mains power supply  
with weak fuses,when you are uncertain as to how well the mains power supply is fused  
andwhenweakgasgeneratorsareusedforcharging.Itmayallowtreeorfourgenerators  
to be connected tothesamewall outlet orfuse group.  
• 50x The fast recycling speed is twice as long as the MAX recycling speed.This setting  
mayallowtwogeneratorstobeconnectedto thesame wall outlet orfusegroup.  
• 75% The extra fast recycling speed is slightly longer than the extremely fast MAX  
recyclingspeed.Itreducesloadby25%andmaypreventsensitivetypesoffusestoblow.  
The rechargespeedisanyhowextremelyfast comparedto otherflashgenerators.  
MAXTheextremeandfastestrecyclingspeed.OnlyonePro-8acanbeconnectedtoone  
wall outletorfusegroup.  
ready lamp/testfunction  
The ready lampandtestbutton functions arecombined.  
Ready lamp [10]isilluminatedwhenthegenerator is fullycharged and ready toflash.  
TestButton[10]isusedtotestthatalllightsettingsarecorrectandthatthefunctionallyis  
as expected.When theTest Button [10] is pressed,the generator will flash and the Ready  
Lamp[10]willturnoffwhilerecharging.Whentherechargeofthegeneratoriscompleted,  
theReady Lamp[10]will beilluminated again.  
flash beforeready  
The ”Flash before readyfunction makes it possible to flash before the recharging of the  
generator is ready and fully completed.When a flash is released before the generator is  
100% recharged a long ”beepwill sound, indicating an underexposed frame. Naturally  
the flash light may not correspond fully to the set value.The underexposure of the frame  
may be so small that it makes no significant difference, however it may be informative  
to get the feeling of the maximum repetition rate.The underexposure frame may still be  
usable if thecatchofthemoment was perfect.  
11  
fan cooling & Protection System  
The Pro-8a generator is equipped with a very effective fan cooling to prevent over heating.  
A microprocessor controlling and supervising the system is integrated for protection and  
safety.Dualfanswillnormallyoperateinsilentmodebutwillspeedupautomaticallywhen  
workinginhotsurroundingsorcontinuouslyathigherpowerlevels.Lowerflashenergyusage  
andnormalroomtemperaturewillslowdownthefanspeedstobeassilentaspossible.  
Ifthereisriskforoverheatingofthegenerator,causedbyabnormalexternalinfluence,the  
protective system will automatically protect the generator from damage.The protective  
system will slow down the recharging intervals and eventually the recharging will stop  
completely.Afterawhile,whenthetemperaturehasdecreasedsufficiently,thegenerator  
will start recharging at a normal pace.This automatic protection will only interfere under  
extreme conditionssuchaswhen theair vents areblocked.  
ThePro-8ageneratorisdesignedtowithstandupto1000fullpowerflashesduringonehour.  
Howeveritisnotadvisabletorunharderthannecessaryduetothelifetimeoftheflashtube.  
notice  
The air vents of the generator must never be blocked or covered in any way.Nor should the generator be operated in an  
enclosed small space. Never store your flash equipment in a car on a hot and sunny day longer than 30 minutes.Avoid  
storageofthegeneratorcloseorbelowthefreezingpointformorethan30minutes.Acoldgeneratormaynotworkproperly  
ormayevenbrakeandwilllosecapacity(flashoutput).Thereisalsoariskoffailurebecauseofcondensationwhenacold  
generator is moved to a warmer surrounding. Remember that the generator has a great temperature storing mass and  
willnotadapttotheindoornormalsurroundingtemperatureuntilafter13hours.NeveruseaPro-8ageneratorthathas  
beenstoredinabnormaltemperaturesformorethan1hour.Awellinsulatedcaseortransportboxwillprolongthetimeof  
storageinabnormaltemperatureto2or3hours.Neveroperatethegeneratorinsideacaseortransportboxduetolackof  
ventilation.Never expose any flash equipmenttowet orhumid environmentsorextremeelectromagnetic fields.  
Additional information  
color temperature  
The color temperature of Pro-8a is calibrated to correspond to daylight and, because of  
thePiPE(patentpending)technology,itremainsperfectlyconstantandreliablefromflash  
to flash and over the entire power range, regardless of the chosen power output and the  
number of flash heads used. This makes the Pro-8a generators perfectly suited for all  
kinds of critical assignments, even with high-resolution digital cameras and backs. In  
combinationwithallactualProflashheadsandlightshapingtoolsthePro-8agenerators  
give neutral and extremely stable color. Please note that other factors, like reflections  
from surrounding objects and ambient lights with non neutral color characteristic, may  
influencethelight colortemperatureand spectra.  
12  
Combining flash tubes and/or glass covers with different coatings can make distinctive  
colortemperatureadjustmentsif needed.  
f-stopStability&range  
The unique PiPE (patent pending) technology ensures extreme light power stability  
from flash to flash as well as over the whole power range.The unique wide power range  
offers maximal flexibility for all situation from light power consuming large objects at  
large distances to really close ups ex. ProRing2 without overexposure with one and the  
sameflashgenerator.Pleasenotethatinfluencefromambientandmodelinglightmakes  
measurementofsmall powerlevels difficult.  
WArninG  
Do not use the light meter’s built-in slave trigger at smaller power levels.Please use a cord and check the shutter  
speedtoavoid ambientlightinfluence.  
flashDuration  
The full power short flash duration has more advantages except from freezing a moving  
object. It will also make it possible to use a very short camera shutter speed to cut out  
exposureinfluencefrom indoorambient light as well as direct sunlight.  
TheflashdurationcanbeshortenedbyreducingthepoweroutputwithFlashLightEnergy  
Control A [8] and/or B [19]. The shortest flash duration using a ProHead and a Pro-8a  
generator is 1/12000 sec at energy setting 3,0 - 3,2 (19 - 21,5Ws).To shorten the flash  
durationathighpower,useaProTwin head.  
I.e.ifyouconnectthetwoplugsofaProTwintotheLampHeadConnectorA[4]andB[15]  
of a Pro-8a 2400Air generator and use both outlets at 1200Ws, the flash duration is just  
1/2200s instead of1/1600s atmaximumpowerwith one ProHead.  
Petrol-electric Generators  
All petrol-electric generators can produce voltage peaks that may damage electronic  
devices.Pro-8aishoweverdesignedtocomplywithsufficientpowerratedpetrol-electric  
generatorssupplyingAC-powerequaltothevoltageandfrequencyspecifiedandwithout  
use of ProGas.  
Onededicated6000Wattpetrol-electricgeneratorisrequiredtopowersupplyonePro-8a  
atMAX speed.  
To supply one Pro-8a generator at 50% recharge speed setting requires one dedicated  
3000W petrol-electricgenerator.  
13  
To supply one Pro-8a generator at 25% recharge speed setting requires one dedicated  
2000Wpetrol-electricgeneratorwhichisthesmallestrecommendedforusewithPro-8a.  
To supply two Pro-8a generators at 50% recharge speed setting requires one 6000W  
petrol-electric generatoretc.  
WArninG  
Only use Pro-8a on the same petrol-electric generator, use of any other flash model simultaneously will cause  
high voltage and may damage the Pro-8a. Pro-8a itself does not cause gas generators to produce high voltages.  
Underratedpower ofapetrol-electricgeneratorwill cause various bad results.  
operating instructions  
Lamp headconnection  
1. If only onelamphead isused,connect thelampto Lamp Head ConnectorA[4].  
2. When connecting the lamp head plug, align the white dot on the plug with the white  
dot to the upper left of the Lamp Head Connector. Secure by turning the ring on the plug  
clockwise.  
Powerconnection  
1. Use the included power cable to connect the generator to the Power Supply (AC)  
Connector[11].  
2. The Power Supply Indicator [12] will be red, indicating that the generator is receiving  
powerbut isin standby mode.  
3. PresstheOn switch [13].  
4. The Power Sypply Indicator [12] will now be green and the Test Button [10] will be  
illuminated.  
5.ViewpowerinW/sorRelativeF-Stops.Press&releaseWsbutton[1]for5sec,totoggle  
flashenergysetting.2beepsconfirmchange.  
6. 1/10th f-stop flash adjustment. Rotate corresponding control dial clockwise to raise  
power or counter clockwise to lower. Each click represents 1/10th f-stop. Three quick  
beepsindicatepowercannotberaiser orloweredfurther.  
7. Full F-Stop Flash Adjustment. Press down while rotating correspondence control dial  
clockwise to raise power or counter clockwise to lower. Each click represents 1 f-stop.  
Three quick beepsindicatepowercannot beraiser orloweredfurther.  
14  
Settings  
1. UsetheModelingLightControl[7]toselectMAXPROP,MAX,PROPor½PROP.Pressthe  
ModelingLightswitch[9]toturn onthemodelinglight.  
2. Use FlashLightEnergyControlA [8] and B[19] to set theenergylevels.  
3. Use the ReadyControl [16]to select BEEP-DIM,BEEP,DIM orOFF.  
4. Use the SpeedControl [18]toselect MAX,75%,50% or25%.  
Sync via cable  
1. ConnectasynccordfromthecameratooneoftheSyncConnectors[2]onthegenerator.  
Syncviacable+flashmeter  
1. ConnectasynccordfromthecameratooneoftheSyncConnectors[2]onthegenerator.  
2. Connect anothersynccablefromtheflashmeter to thefree Sync Connector [2].  
Sync via Photocell /ir-slave  
1. ConnectanIR transmittertothecamera.  
2. Turn the SyncControl [5]toSLAVE.  
Syncvia radio(ProfotoAir)  
1. ConnectanAirRemoteorAir Sync unit to thecamera.  
2. Turn the SyncControl [5]toRADIO.  
3. Pro-8a isnowreadytoflash,with theselected radio channel.  
Wirelessremotecontrol  
ForAirRemotecontrol,bothradiochannelandgrouphavetobeset.Thegroupcanbeset  
individually for each lamp head.For wireless use with Profoto Studio 2 andAIR USB,only  
radio channel hastobeset.  
Changingradiochannel andgroup settings:  
1. Turnthe SyncControl [5]toSET.  
2. The radio channel and group setting for the individual lamp head is shown separately  
inFlashLightEnergyDisplayA[8]orB[19]asaradiochannelnumber(1-8)followedbya  
group letter(A-F).  
15  
3. TurnFlashLightEnergyControlA[8]orB[19]clockwise/counter-clockwisetoincrease/  
decrease theradiochannelnumber.  
4. PushandturnFlashLightEnergyControlA[8]clockwise/counter-clockwisetoincrease/  
decrease thegroupsettingforlamp headA [4].  
5. Push and turn Flash Light Energy Control B [19] clockwise/counter-clockwise to  
increase/decreasethegroupsetting for lamphead B[15].  
6. Turnthe SyncControl [5]toRADIO.  
turnoffgenerator  
1. The modeling light, energy level, radio channel and group settings are automatically  
savedassoonastheyarechangedand will beavailable at start up.  
2. PresstheOn switch [13]toturnoff thepower.  
3. The Power Supply Indicator [12] will be red, indicating that the generator is receiving  
powerbut isin standby mode.  
4. Removethepowercable.  
technical data  
Profoto Pro-8a 2400 Air  
General  
Energy  
2400Ws  
Energy Distribution  
ChannelA 5–2400Ws1.0–10.0  
Channel B5–1200Ws1.0–9.0  
Energy Control Range  
RecyclingTime  
1.0–10.0 f stop(5–2400Ws )  
0.05–0.9s  
16  
Flashrate at1.0//4.0//6.0//8.0//10.0 20//15//10//4//1(flash repetitionrateper  
second at maxrecharging speed)  
FlashDurationt0,5  
1/12000–1/1600 s  
Fastestcamerashutterspeed 2400Ws 1/500 with cable,IRorProfotoAirfast mode.  
1/250with normal ProfotoAir  
Maxleaf shuttercameraspeed  
Dependingofthespecificcamerasleafshutters  
openingand closing time delays  
Modeling LampsTotalW/Pack(max) 1000W  
Modeling LampsW/Head (max)  
Energy Control Increments  
Energy stability flashtoflash  
Colorstabilityflashtoflash  
500W  
1/10f-stopand full f-stops  
+/-1/50 f-stop  
+/-40 °K  
Colorstabilityenergyrange10.0–5.0 +/-50 °K  
Colorstabilityenergyrange10.03.0 +/-110°K  
Colorstabilityenergyrange10.0–1.0 +/-190 °K  
Guide number@ 2meters100ASA  
with Magnumreflector  
128  
Specifieddataconditions  
Input Powersupply  
A standard ProHead,120 or230VAC  
100–127V/ 200–240V,50/60Hz(Nominal)  
Synchronization andcontrol  
Sync Socket(s)  
2
Lamp HeadSocket(s)  
Wire Sync  
2
Compliant to ISO 10330Standard  
WireSync Connectors  
Photocell/IR-slaveandSwitch  
USBInterface  
2(¼inchphono plug)  
Yes,with automaticsensitivityadjustment  
USB2.0Full Speedcompatible  
Wirelesssync  
Yes,ProfotoAir (LPA PocketWizard insideis  
available on special order)  
WirelessRemoteControl  
Yes,ProfotoAir (Not available with LPAPocket  
wizard)  
WirelessRadioRange  
ComputerControl  
Upto 300m  
Yes,ProfotoStudio viaProfotoAirorUSB cable  
17  
Miscellaneous  
Digital Display  
Yes,f-stop orWs  
Fan Cooled  
Yes,two speedregulated  
Automatic Multi-Voltage  
Yes,powersupplied worldwidewithout  
changingthestd headmodeling lamp  
Ready Signal  
Yes,beepsoundand dimmingofmodeling light  
during recharge  
Auto Dumping  
Yes,can also be dumpedmanually  
Yes (100%,75%,50%,25%) See alsospeed  
Slow blow fuse 16A / 230V,20A/110V  
AutomaticfusetypeC,D,E16A/230V,20A/110V  
Seealso speed control  
Speed Control control  
Fuse Requirementperunitat  
Maxspeed setting  
Measurements  
Dimensions  
Weight  
37x18.5x25cm;14.5x7.3x9.8 in  
12.2 kg; 26.9 lbs  
technical data  
Profoto Pro-8a 1200 Air  
General  
Energy  
1200Ws  
Energy Distribution  
ChannelA 5–1200Ws 2.0–10.0  
Channel B5–600Ws 2.0–9.0  
2.0–10.0f stop (5–1200Ws)  
0.05–0.5s  
Energy Control Range  
RecyclingTime  
18  
Flashrate at1.0//4.0//6.0//8.0//10.0 20//17//11//7//2(flash repetitionrateper  
second at maxrecharging speed)  
FlashDurationt0,5  
1/12000–1/2200 s  
Fastestcamerashutterspeed 2400Ws 1/500 with cable,IRorProfotoAirfast mode.  
1/250with normal ProfotoAir  
Maxleaf shuttercameraspeed  
Dependingofthespecificcamerasleafshutters  
openingand closing time delays  
Modeling LampsTotalW/Pack(max) 1000W  
Modeling LampsW/Head (max)  
Energy Control Increments  
Energy stability flashtoflash  
Colorstabilityflashtoflash  
500W  
1/10f-stopand full f-stops  
+/-1/50 f-stop  
+/-40 °K  
Colorstabilityenergyrange10.0–6.0 +/-40°K  
Colorstabilityenergyrange10.0–4.0 +/-80 °K  
Colorstabilityenergyrange10.0–2.0 +/-160°K  
Guide number@ 2meters100ASA  
with Magnumreflector  
90  
Specifieddataconditions  
Input Powersupply  
A standardProHead,120 or230VAC  
100–127V/ 200–240V,50/60Hz(Nominal)  
Synchronization andcontrol  
Sync Socket(s)  
2
Lamp HeadSocket(s)  
Wire Sync  
2
Compliant to ISO 10330Standard  
WireSync Connectors  
Photocell/IR-slaveandSwitch  
USBInterface  
2(¼inchphono plug)  
Yes,with automaticsensitivityadjustment  
USB2.0Full Speedcompatible  
Wirelesssync  
Yes,ProfotoAir (LPA PocketWizard insideis  
available on special order)  
WirelessRemoteControl  
Yes,ProfotoAir (Not available with LPAPocket  
wizard)  
WirelessRadioRange  
ComputerControl  
Upto 300m  
Yes,ProfotoStudio viaProfotoAirorUSB cable  
19  
Miscellaneous  
Digital Display  
Yes,f-stop orWs  
Fan Cooled  
Yes,two speedregulated  
Automatic Multi-Voltage  
Yes,powersupplied worldwidewithout  
changingthestd headmodeling lamp  
Ready Signal  
Yes,beepsoundand dimmingofmodeling light  
during recharge  
Auto Dumping  
Yes,can also be dumpedmanually  
Yes (100%,75%,50%,25%) See alsospeed  
Slow blow fuse 16A / 230V,20A/110V  
AutomaticfusetypeC,D,E16A/230V,20A/110V  
Seealso speed control  
Speed Control control  
Fuse Requirementperunitat  
Maxspeed setting  
Measurements  
Dimensions  
Weight  
34.5x18.5x25 cm;13.6x7.3x9.8in  
11.4 kg; 25.2 lbs  
3. Turn Flash Light Energy Control A [8] or B [19] clockwise/  
counterclockwisetoincrease/decreasetheradiochannelnumber.  
4. Push and turn Flash Light Energy Control A [8] clockwise/  
counterclockwise to increase/decrease the group setting for  
lampheadA[4].  
Quick Guide  
This Quick Guide refers to the User’s Guide and helps you to  
quicklygetstarted usingthePro-8asystem.  
5. Push and turn Flash Light Energy Control B [19] clockwise/  
counterclockwise to increase/decrease the group setting for  
lampheadB[15].  
If you in any way are unsure of how to use the system, read and follow the  
safetyinstructionsintheUser’sGuidecarefullytoavoidinjuriesordamages!  
6.TurntheSyncControl[5]toRADIO.  
operatinginstructions  
turnoffgenerator  
Lampheadconnections  
1. The modeling light, energy level, radio channel and group  
settings are automatically saved as soon as they are changed  
andwillbeavailableatstartup.  
1. If only one lamp head is used, connect the lamp to the Lamp  
Head ConnectorA[4].  
2.When connecting the lamp head plug,align the white dots on  
the plug with the white dot to the upper left of the Lamp Head  
Connector.Secureby turningtheringontheplugclockwise.  
2.PresstheOnswitch[13]toturnoffthepower.  
3.ThePowerSupplyIndicator[12]willbered,indicatingthatthe  
generatorisreceivingpowerbutisinstandbymode.  
4.Remove thePowercable.  
Powerconnection  
1.Use the included power cable to connect the generator to the  
PowerSupply (AC) Connector[11].  
2.ThePowerSupplyIndicator[12]willbered,indicatingthatthe  
generator isreceiving powerbutisinstandbymode.  
3.PresstheOn switch[13].  
4.ThePowerSupplyIndicator[12]willnowbegreenandtheTest  
Button [10]will beilluminated.  
LampHeads  
21  
Pro-8aisdesignedforallofthepresentstate-of-the-artProHeads  
andlightshapingtools.ForselectedpreviousmodelsofProfotos  
lamp heads there is a simple update for compatible fan cooling  
on100–120Vmarkets.  
5. View power in W/s or Relative F-Stops. Press & release Ws  
button [1] for 5 sec, to toggle flash energy setting. 2 beeps  
confirmchange.  
6.1/10th f-stop flash adjustment.Rotate corresponding control  
dialclockwisetoraisepowerorcounterclockwisetolower.Each  
clickrepresents1/10thf-stop.Threequickbeepsindicatepower  
cannotberaiserorloweredfurther.  
7. Full F-Stop Flash Adjustment. Press down while rotating  
correspondencecontroldialclockwisetoraisepowerorcounter  
clockwise to lower. Each click represents 1 f-stop.Three quick  
beepsindicatepowercannotberaiserorloweredfurther.  
ProHead  
The standard heavy-duty head is the Profoto ProHead, built for  
producing flashes with Pro-8a, up to 2400 Ws over and over  
again,hourafterhour.Ithasanintegratedhighefficient,longlife  
halogen lamp with a switch and a fuse. A thermally controlled  
2-speed efficient fan provide silent cooling. For safety reasons  
thermalprotectionisbuilt-in.  
The flash tube and halogen lamp are protected by a diffusing  
glasscoveralsoservingasalightsourcecorrespondingfilterand  
colorcorrectionfilter.Optionalglasscoverversionsareavailable.  
The optimized flash tube is made by high grade UV-free filtered  
quartsglassandheavydutyelectrodestomaximizelifetime.  
Settings  
1. Use the Modeling Light Control [7] to select MAX PROP, MAX,  
PROP or ½ PROP. Press the Modeling Light switch [9] to turn on  
themodeling light.  
Protwin  
Whendemandsareeventougher,theProfotoProTwinisavailable  
with two flash tubes that effectively double the performance.  
Used with a single generator, it can produce shorter fl ash  
durations by splitting half of the power to two fl ash tubes.Used  
with two Pro-8a 2400 Air, it can half the recycling speed or  
doublethelightenergy,upto4800Ws.Poweredfromoneofthe  
two connected cables ProTwin has an integrated high efficient  
halogen lamp with a switch and a fuse. A thermally controlled  
2-speed efficient fan provides silent cooling.For safety reasons  
thermal protection is built-in. The flashtube and halogen lamp  
are protected by a diffusing glass cover also serving as a light  
source corresponding filter and color correction filter. Optional  
glass cover versions are available. The optimized flash tube is  
madebyhighgradeUV-freefilteredquartsglassandheavyduty  
electrodestomaximizelifetime.  
2. Use Flash Light Energy Control A [8] and B [19] to set the  
energylevels.  
3.UsetheReadyControl[16]toselectBEEP-DIM,BEEP,DIMorOFF.  
4.UsetheSpeedControl[18]toselectMAX,75%,50%or25%.  
Sync viacable  
1. Connect a sync cord from the camera to one of the Sync  
Connectors[2] onthegenerator.  
Syncviacable+ flashmeter  
1. Connect a sync cord from the camera to one of the Sync  
Connectors[2] onthegenerator.  
2. Connect another sync cable from the flash meter to the free  
SyncConnector[2].  
Sync viaPhotocell/ir-slave  
1.Connect anIR transmittertothecamera.  
2.TurntheSyncControl [5]toSLAVE.  
Proring  
If you look for a more lightweight ring flash without modeling  
light, there’s the Profoto ProRing, with the capacity of up to  
four 2400 Ws flashes per minute. An entirely mobile source  
of light, the ring flash fits all Pro-7 generators. The adjustable  
tripod mount bracket and the wide interior (100 mm diameter)  
makestheProRingcompatiblewithalltypesofcamerasaswell  
as most lenses. Optional accessory reflectors expand the ring  
flash’scapabilitiesfurther.  
Sync viaradio(Profoto Air)  
1.Connect anAir RemoteorAirSync unittothecamera.  
2.TurntheSyncControl [5]toRADIO.  
3.Pro-8aisnowready toflash,withtheselectedradioChannel.  
Wirelessremote control  
For Air Remote control, both radio channel and group have to  
be set. The group can be set individually for each lamp head.  
For wireless use with Profoto Studio 2 and AIR USB, only radio  
channel hastobeset.  
Proring2  
For fashion or macro photography, when you want a direct and  
very prominent light,the Profoto ProRing 2 provides a ring flash  
capableofunlimitedflashrepetitionrateduetobuilt-inthermally  
controlled silent and efficient fan cooling. The optimized flash  
tube is made by high grade UV-free filtered quarts glass and  
heavy duty electrodes to maximize lifetime. 200 W of powerful  
halogenmodelinglightarebuilt-inwith switch and fuse.  
changingradiochannelandgroup settings:  
1.TurntheSyncControl [5]toSET.  
2. The radio channel and group setting for the individual lamp  
head is shown separately in Flash Light Energy Display A [6]  
or B [17] as a radio channel number (1–8) followed by a group  
letter(A–F).  
ProfotoAB  
P.O.Box2023  
SE-128 21 Skarpnäck  
SWEDEN  
Phone+46 8 447 53 00  

Radio Shack CID 947 User Manual
Pioneer AVD W6200 User Manual
Philips SOUNDMACHINE AZAZ1301 User Manual
Pentax Camcorder IQZoom140 User Manual
Panasonic NV VZ10B User Manual
Olympus VS259601 User Manual
O'Brien Big Baller 2091515 User Manual
Nokia BH 203 User Manual
Listen Technologies LA 325 User Manual
Kenwood Car Stereo System KDV MP7032 User Manual